This patch adds glue layer for support of sdhci driver on ST SPEAr platform.
Signed-off-by: Viresh Kumar <viresh.kumar@xxxxxx>
---
MAINTAINERS | 6 +
drivers/mmc/host/Kconfig | 12 ++
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/sdhci-spear.c | 300 +++++++++++++++++++++++++++++++++++++++
include/linux/mmc/sdhci-spear.h | 42 ++++++
5 files changed, 361 insertions(+), 0 deletions(-)
create mode 100644 drivers/mmc/host/sdhci-spear.c
create mode 100644 include/linux/mmc/sdhci-spear.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 0369b22..bbff70a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4938,6 +4938,12 @@ L: linux-mmc@xxxxxxxxxxxxxxx
S: Maintained
F: drivers/mmc/host/sdhci-s3c.c
+SECURE DIGITAL HOST CONTROLLER INTERFACE (SDHCI) ST SPEAR DRIVER
+M: Viresh Kumar <viresh.kumar@xxxxxx>
+L: linux-mmc@xxxxxxxxxxxxxxx
+S: Maintained
+F: drivers/mmc/host/sdhci-spear.c
+
SECURITY SUBSYSTEM
M: James Morris <jmorris@xxxxxxxxx>
L: linux-security-module@xxxxxxxxxxxxxxx (suggested Cc:)
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 2e13b94..40eae7e 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -136,6 +136,18 @@ config MMC_SDHCI_S3C
If unsure, say N.
+config MMC_SDHCI_SPEAR
+ tristate "SDHCI support on ST SPEAr platform"
+ depends on MMC_SDHCI && PLAT_SPEAR
+ help
+ This selects the Secure Digital Host Controller Interface (SDHCI)
+ often referrered to as the HSMMC block in some of the ST SPEAR range
+ of SoC
+
+ If you have a controller with this interface, say Y or M here.
+
+ If unsure, say N.
+
config MMC_SDHCI_S3C_DMA
bool "DMA support on S3C SDHCI"
depends on MMC_SDHCI_S3C && EXPERIMENTAL
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index f480397..d00a9fa 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -14,6 +14,7 @@ obj-$(CONFIG_MMC_SDHCI) += sdhci.o
obj-$(CONFIG_MMC_SDHCI_PCI) += sdhci-pci.o
obj-$(CONFIG_MMC_SDHCI_PLTFM) += sdhci-pltfm.o
obj-$(CONFIG_MMC_SDHCI_S3C) += sdhci-s3c.o
+obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o
obj-$(CONFIG_MMC_WBSD) += wbsd.o
obj-$(CONFIG_MMC_AU1X) += au1xmmc.o
obj-$(CONFIG_MMC_OMAP) += omap.o
diff --git a/drivers/mmc/host/sdhci-spear.c b/drivers/mmc/host/sdhci-spear.c
new file mode 100644
index 0000000..6d3f740
--- /dev/null
+++ b/drivers/mmc/host/sdhci-spear.c
@@ -0,0 +1,300 @@
+/*
+ * drivers/mmc/host/sdhci-spear.c
+ *
+ * Support of SDHCI platform devices for spear soc family
+ *
+ * Copyright (C) 2010 ST Microelectronics
+ * Viresh Kumar<viresh.kumar@xxxxxx>
+ *
+ * Inspired by sdhci-pltfm.c
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/highmem.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/sdhci-spear.h>
+#include <linux/io.h>
+#include "sdhci.h"
+
+struct spear_sdhci {
+ struct clk *clk;
+ struct sdhci_plat_data *data;
+};
+
+/* sdhci ops */
+static struct sdhci_ops sdhci_pltfm_ops = {
+ /* Nothing to do for now. */
+};
+
+/* gpio card detection interrupt handler */
+static irqreturn_t sdhci_gpio_irq(int irq, void *dev_id)
+{
+ struct platform_device *pdev = dev_id;
+ struct sdhci_host *host = platform_get_drvdata(pdev);
+ struct spear_sdhci *sdhci =
+ (struct spear_sdhci *)(pdev->dev.platform_data);
+ unsigned long gpio_irq_type;
+ int val;
+
+ val = gpio_get_value(sdhci->data->card_int_gpio);
+
+ /* val == 1 -> card removed, val == 0 -> card inserted */
+ /* if card removed - set irq for low level, else vice versa */
+ gpio_irq_type = val ? IRQF_TRIGGER_LOW : IRQF_TRIGGER_HIGH;
+ set_irq_type(irq, gpio_irq_type);
+
+ if (sdhci->data->card_power_gpio >= 0) {
+ if (!sdhci->data->power_always_enb) {
+ /* if card inserted, give power, otherwise remove it */
+ val = sdhci->data->power_active_high ? !val : val ;
+ gpio_set_value(sdhci->data->card_power_gpio, val);
+ }
+ }
+
+ /* inform sdhci driver about card insertion/removal */
+ tasklet_schedule(&host->card_tasklet);
+
+ return IRQ_HANDLED;
+}
+
+static int __devinit sdhci_probe(struct platform_device *pdev)
+{
+ struct sdhci_host *host;
+ struct resource *iomem;
+ struct spear_sdhci *sdhci;
+ int ret;
+
+ BUG_ON(pdev == NULL);
+
+ iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!iomem) {
+ ret = -ENOMEM;
+ dev_dbg(&pdev->dev, "memory resource not defined\n");
+ goto err;
+ }
+
+ if (!request_mem_region(iomem->start, resource_size(iomem),
+ "spear-sdhci")) {
+ ret = -EBUSY;
+ dev_dbg(&pdev->dev, "cannot request region\n");
+ goto err;
+ }
+
+ sdhci = kzalloc(sizeof(*sdhci), GFP_KERNEL);
+ if (!sdhci) {
+ ret = -ENOMEM;
+ dev_dbg(&pdev->dev, "cannot allocate memory for sdhci\n");
+ goto err_kzalloc;
+ }
+
+ /* clk enable */
+ sdhci->clk = clk_get(&pdev->dev, NULL);
+ if (IS_ERR(sdhci->clk)) {
+ ret = PTR_ERR(sdhci->clk);
+ dev_dbg(&pdev->dev, "Error getting clock\n");
+ goto err_clk_get;
+ }
+
+ ret = clk_enable(sdhci->clk);
+ if (ret) {
+ dev_dbg(&pdev->dev, "Error enabling clock\n");
+ goto err_clk_enb;
+ }
+
+ /* overwrite platform_data */
+ sdhci->data = (struct sdhci_plat_data *)(pdev->dev.platform_data);
+ pdev->dev.platform_data = sdhci;
+
+ if (pdev->dev.parent)
+ host = sdhci_alloc_host(pdev->dev.parent, 0);
+ else
+ host = sdhci_alloc_host(&pdev->dev, 0);
+
+ if (IS_ERR(host)) {
+ ret = PTR_ERR(host);
+ dev_dbg(&pdev->dev, "error allocating host\n");
+ goto err_alloc_host;
+ }
+
+ host->hw_name = "sdhci";
+ host->ops = &sdhci_pltfm_ops;
+ host->irq = platform_get_irq(pdev, 0);
+ host->quirks = SDHCI_QUIRK_BROKEN_ADMA;
+
+ host->ioaddr = ioremap(iomem->start, resource_size(iomem));
+ if (!host->ioaddr) {
+ ret = -ENOMEM;
+ dev_dbg(&pdev->dev, "failed to remap registers\n");
+ goto err_ioremap;
+ }
+
+ ret = sdhci_add_host(host);
+ if (ret) {
+ dev_dbg(&pdev->dev, "error adding host\n");
+ goto err_add_host;
+ }
+
+ platform_set_drvdata(pdev, host);
+
+ /*
+ * It is optional to use GPIOs for sdhci Power control & sdhci card
+ * interrupt detection. If sdhci->data is NULL, then use original sdhci
+ * lines otherwise GPIO lines.
+ * If GPIO is selected for power control, then power should be disabled
+ * after card removal and should be enabled when card insertion
+ * interrupt occurs
+ */
+ if (!sdhci->data)
+ return 0;
+
+ if (sdhci->data->card_power_gpio >= 0) {
+ int val = 0;
+
+ ret = gpio_request(sdhci->data->card_power_gpio, "sdhci");
+ if (ret < 0) {
+ dev_dbg(&pdev->dev, "gpio request fail: %d\n",
+ sdhci->data->card_power_gpio);
+ goto err_pgpio_request;
+ }
+
+ if (sdhci->data->power_always_enb)
+ val = sdhci->data->power_active_high;
+ else
+ val = !sdhci->data->power_active_high;
+
+ ret = gpio_direction_output(sdhci->data->card_power_gpio, val);
+ if (ret) {
+ dev_dbg(&pdev->dev, "gpio set direction fail: %d\n",
+ sdhci->data->card_power_gpio);
+ goto err_pgpio_direction;
+ }
+
+ gpio_set_value(sdhci->data->card_power_gpio, 1);
+ }
+
+ if (sdhci->data->card_int_gpio >= 0) {
+ ret = gpio_request(sdhci->data->card_int_gpio, "sdhci");
+ if (ret < 0) {
+ dev_dbg(&pdev->dev, "gpio request fail: %d\n",
+ sdhci->data->card_int_gpio);
+ goto err_igpio_request;
+ }
+
+ ret = gpio_direction_input(sdhci->data->card_int_gpio);
+ if (ret) {
+ dev_dbg(&pdev->dev, "gpio set direction fail: %d\n",
+ sdhci->data->card_int_gpio);
+ goto err_igpio_direction;
+ }
+ ret = request_irq(gpio_to_irq(sdhci->data->card_int_gpio),
+ sdhci_gpio_irq, IRQF_TRIGGER_LOW,
+ mmc_hostname(host->mmc), pdev);
+ if (ret) {
+ dev_dbg(&pdev->dev, "gpio request irq fail: %d\n",
+ sdhci->data->card_int_gpio);
+ goto err_igpio_request_irq;
+ }
+
+ }
+
+ return 0;
+
+err_igpio_request_irq:
+err_igpio_direction:
+ if (sdhci->data->card_int_gpio >= 0)
+ gpio_free(sdhci->data->card_int_gpio);
+err_igpio_request:
+err_pgpio_direction:
+ if (sdhci->data->card_power_gpio >= 0)
+ gpio_free(sdhci->data->card_power_gpio);
+err_pgpio_request:
+ platform_set_drvdata(pdev, NULL);
+ sdhci_remove_host(host, 1);
+err_add_host:
+ iounmap(host->ioaddr);
+err_ioremap:
+ sdhci_free_host(host);
+err_alloc_host:
+ clk_disable(sdhci->clk);
+err_clk_enb:
+ clk_put(sdhci->clk);
+err_clk_get:
+ kfree(sdhci);
+err_kzalloc:
+ release_mem_region(iomem->start, resource_size(iomem));
+err:
+ dev_err(&pdev->dev, "spear-sdhci probe failed: %d\n", ret);
+ return ret;
+}
+
+static int __devexit sdhci_remove(struct platform_device *pdev)
+{
+ struct sdhci_host *host = platform_get_drvdata(pdev);
+ struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ struct spear_sdhci *sdhci =
+ (struct spear_sdhci *)(pdev->dev.platform_data);
+ int dead;
+ u32 scratch;
+
+ if (sdhci->data) {
+ if (sdhci->data->card_int_gpio >= 0) {
+ free_irq(gpio_to_irq(sdhci->data->card_int_gpio), pdev);
+ gpio_free(sdhci->data->card_int_gpio);
+ }
+
+ if (sdhci->data->card_power_gpio >= 0)
+ gpio_free(sdhci->data->card_power_gpio);
+ }
+
+ platform_set_drvdata(pdev, NULL);
+ dead = 0;
+ scratch = readl(host->ioaddr + SDHCI_INT_STATUS);
+ if (scratch == (u32)-1)
+ dead = 1;
+
+ sdhci_remove_host(host, dead);
+ iounmap(host->ioaddr);
+ sdhci_free_host(host);
+ clk_disable(sdhci->clk);
+ clk_put(sdhci->clk);
+ kfree(sdhci);
+ if (iomem)
+ release_mem_region(iomem->start, resource_size(iomem));
+
+ return 0;
+}
+
+static struct platform_driver sdhci_driver = {
+ .driver = {
+ .name = "sdhci",
+ .owner = THIS_MODULE,
+ },
+ .probe = sdhci_probe,
+ .remove = __devexit_p(sdhci_remove),
+};
+
+static int __init sdhci_init(void)
+{
+ return platform_driver_register(&sdhci_driver);
+}
+module_init(sdhci_init);
+
+static void __exit sdhci_exit(void)
+{
+ platform_driver_unregister(&sdhci_driver);
+}
+module_exit(sdhci_exit);
+
+MODULE_DESCRIPTION("SPEAr Secure Digital Host Controller Interface driver");
+MODULE_AUTHOR("Viresh Kumar <viresh.kumar@xxxxxx>");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mmc/sdhci-spear.h b/include/linux/mmc/sdhci-spear.h
new file mode 100644
index 0000000..9188c97
--- /dev/null
+++ b/include/linux/mmc/sdhci-spear.h
@@ -0,0 +1,42 @@
+/*
+ * include/linux/mmc/sdhci-spear.h
+ *
+ * SDHCI declarations specific to ST SPEAr platform
+ *
+ * Copyright (C) 2010 ST Microelectronics
+ * Viresh Kumar<viresh.kumar@xxxxxx>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef MMC_SDHCI_SPEAR_H
+#define MMC_SDHCI_SPEAR_H
+
+#include <linux/platform_device.h>
+/*
+ * struct sdhci_plat_data: spear sdhci platform data structure
+ *
+ * @card_power_gpio: gpio pin for enabling/disabling power to sdhci socket
+ * @power_active_high: if set, enable power to sdhci socket by setting
+ * card_power_gpio
+ * @power_always_enb: If set, then enable power on probe, otherwise enable only
+ * on card insertion and disable on card removal.
+ * card_int_gpio: gpio pin used for card detection
+ */
+struct sdhci_plat_data {
+ int card_power_gpio;
+ int power_active_high;
+ int power_always_enb;
+ int card_int_gpio;
+};
+
+/* This function is used to set platform_data field of pdev->dev */
+static inline void
+sdhci_set_plat_data(struct platform_device *pdev, struct sdhci_plat_data *data)
+{
+ pdev->dev.platform_data = data;
+}
+
+#endif /* MMC_SDHCI_SPEAR_H */
--
1.6.0.2
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
