On Mon, 2019-06-24 at 07:43 +0200, Christoph Hellwig wrote: > When we get booted we want a clear slate without any leaks from > previous > supervisors or the firmware. Flush the instruction cache and then > clear > all registers to known good values. This is really important for the > upcoming nommu support that runs on M-mode, but can't really harm > when > running in S-mode either. That means it should be done for S-mode as well. Right ? I see the reset code is enabled only for M-mode only. > Vaguely based on the concepts from opensbi. > > Signed-off-by: Christoph Hellwig <hch@xxxxxx> > --- > arch/riscv/kernel/head.S | 85 > ++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 85 insertions(+) > > diff --git a/arch/riscv/kernel/head.S b/arch/riscv/kernel/head.S > index a4c170e41a34..74feb17737b4 100644 > --- a/arch/riscv/kernel/head.S > +++ b/arch/riscv/kernel/head.S > @@ -11,6 +11,7 @@ > #include <asm/thread_info.h> > #include <asm/page.h> > #include <asm/csr.h> > +#include <asm/hwcap.h> > > __INIT > ENTRY(_start) > @@ -19,6 +20,12 @@ ENTRY(_start) > csrw CSR_XIP, zero > > #ifdef CONFIG_M_MODE > + /* flush the instruction cache */ > + fence.i > + > + /* Reset all registers except ra, a0, a1 */ > + call reset_regs > + > /* > * The hartid in a0 is expected later on, and we have no > firmware > * to hand it to us. > @@ -168,6 +175,84 @@ relocate: > j .Lsecondary_park > END(_start) > > +#ifdef CONFIG_M_MODE > +ENTRY(reset_regs) > + li sp, 0 > + li gp, 0 > + li tp, 0 > + li t0, 0 > + li t1, 0 > + li t2, 0 > + li s0, 0 > + li s1, 0 > + li a2, 0 > + li a3, 0 > + li a4, 0 > + li a5, 0 > + li a6, 0 > + li a7, 0 > + li s2, 0 > + li s3, 0 > + li s4, 0 > + li s5, 0 > + li s6, 0 > + li s7, 0 > + li s8, 0 > + li s9, 0 > + li s10, 0 > + li s11, 0 > + li t3, 0 > + li t4, 0 > + li t5, 0 > + li t6, 0 > + csrw sscratch, 0 > + > +#ifdef CONFIG_FPU > + csrr t0, misa > + andi t0, t0, (COMPAT_HWCAP_ISA_F | COMPAT_HWCAP_ISA_D) > + bnez t0, .Lreset_regs_done > + > + li t1, SR_FS > + csrs sstatus, t1 > + fmv.s.x f0, zero > + fmv.s.x f1, zero > + fmv.s.x f2, zero > + fmv.s.x f3, zero > + fmv.s.x f4, zero > + fmv.s.x f5, zero > + fmv.s.x f6, zero > + fmv.s.x f7, zero > + fmv.s.x f8, zero > + fmv.s.x f9, zero > + fmv.s.x f10, zero > + fmv.s.x f11, zero > + fmv.s.x f12, zero > + fmv.s.x f13, zero > + fmv.s.x f14, zero > + fmv.s.x f15, zero > + fmv.s.x f16, zero > + fmv.s.x f17, zero > + fmv.s.x f18, zero > + fmv.s.x f19, zero > + fmv.s.x f20, zero > + fmv.s.x f21, zero > + fmv.s.x f22, zero > + fmv.s.x f23, zero > + fmv.s.x f24, zero > + fmv.s.x f25, zero > + fmv.s.x f26, zero > + fmv.s.x f27, zero > + fmv.s.x f28, zero > + fmv.s.x f29, zero > + fmv.s.x f30, zero > + fmv.s.x f31, zero > + csrw fcsr, 0 > +#endif /* CONFIG_FPU */ > +.Lreset_regs_done: > + ret > +END(reset_regs) > +#endif /* CONFIG_M_MODE */ > + > __PAGE_ALIGNED_BSS > /* Empty zero page */ > .balign PAGE_SIZE -- Regards, Atish
