On Thu, Apr 20, 2023 at 4:09 AM Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx> wrote: > > On 19/04/2023 09:17, Binbin Zhou wrote: > > Add Loongson Extended I/O Interrupt controller binding with DT schema > > format using json-schema. > > > > Signed-off-by: Binbin Zhou <zhoubinbin@xxxxxxxxxxx> > > --- > > .../loongson,eiointc.yaml | 74 +++++++++++++++++++ > > 1 file changed, 74 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/interrupt-controller/loongson,eiointc.yaml > > > > diff --git a/Documentation/devicetree/bindings/interrupt-controller/loongson,eiointc.yaml b/Documentation/devicetree/bindings/interrupt-controller/loongson,eiointc.yaml > > new file mode 100644 > > index 000000000000..4ab4efb061e1 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/interrupt-controller/loongson,eiointc.yaml > > @@ -0,0 +1,74 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/interrupt-controller/loongson,eiointc.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Loongson Extended I/O Interrupt Controller > > + > > +maintainers: > > + - Binbin Zhou <zhoubinbin@xxxxxxxxxxx> > > + > > +description: | > > + This interrupt controller is found on the Loongson-3 family chips and > > + Loongson-2K series chips and is used to distribute interrupts directly to > > + individual cores without forwarding them through the HT's interrupt line. > > + > > +allOf: > > + - $ref: /schemas/interrupt-controller.yaml# > > + > > +properties: > > + compatible: > > + enum: > > + - loongson,ls2k0500-eiointc > > + - loongson,ls2k2000-eiointc > > + > > + reg: > > + items: > > + - description: Interrupt enable registers > > + - description: Interrupt status registers > > + - description: Interrupt clear registers > > + - description: Interrupt routing configuration registers > > + > > + reg-names: > > + items: > > + - const: enable > > + - const: status > > + - const: clear > > + - const: route > > + > > + interrupts: > > + maxItems: 1 > > + > > + interrupt-controller: true > > + > > + '#interrupt-cells': > > + const: 1 > > + > > +required: > > + - compatible > > + - reg > > + - interrupts > > + - interrupt-controller > > + - '#interrupt-cells' > > + > > +unevaluatedProperties: false > > + > > +examples: > > + - | > > + eiointc: interrupt-controller@1fe11600 { > > + compatible = "loongson,ls2k0500-eiointc"; > > + reg = <0x1fe11600 0x10>, > > + <0x1fe11700 0x10>, > > + <0x1fe11800 0x10>, > > + <0x1fe114c0 0x4>; > > Binding is OK, but are you sure you want to split the address space like > this? It looks like two address spaces (enable+clear+status should be > one). Are you sure this is correct? > Hi Krzysztof: These registers are all in the range of chip configuration registers, in the case of LS2K0500, which has a base address of 0x1fe10000. However, the individual register addresses are not contiguous with each other, and most are distributed across modules, so I feel that they should be listed in detail as they are used. Thanks. Binbin > Best regards, > Krzysztof > >
