On 8/12/2014 10:23 am, Grazvydas Ignotas wrote:
Hi,
On Sun, Dec 7, 2014 at 9:23 PM, Laurent Pinchart
<laurent.pinchart@xxxxxxxxxxxxxxxx> wrote:
Hi Grazvydas,
(CC'ing Paulo Assis)
On Saturday 06 December 2014 02:25:25 Grazvydas Ignotas wrote:
On Fri, Dec 5, 2014 at 1:46 PM, Laurent Pinchart wrote:
On Thursday 06 November 2014 00:29:53 Grazvydas Ignotas wrote:
On Wed, Nov 5, 2014 at 4:05 PM, Laurent Pinchart wrote:
Would you be able to capture images from the C920 using yavta, with the
uvcvideo trace parameter set to 4096, and send me both the yavta log
and the kernel log ? Let's start with a capture sequence of 50 to 100
images.
I've done 2 captures, if that helps:
http://notaz.gp2x.de/tmp/c920_yavta/
The second one was done using low exposure setting, which allows
camera to achieve higher frame rate.
Thank you for the log, they were very helpful. They revealed that the USB
SOF (Start Of Frame) counter values on the device and host side are not
in sync. The counters get incremented are very different rates. What USB
controller are you using ?
00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI
Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: Micro-Star International Co., Ltd. [MSI] Device 7592
Flags: bus master, medium devsel, latency 0, IRQ 23
Memory at fe9fbc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci-pci
If it helps, I could try on an ARM board, currently don't have any
other x86 hardware around.
Actually the frequencies I've computed from the log are correct on the host
side but quite off on the device side. I'm puzzled.
The following patch allows accessing the contents of the clock data buffer
through debugfs. Would you be able to apply it and execute the following
steps ?
1. Load the uvcvideo module with the clock trace flag (0x1000) set.
2. Start capturing clock data.
while true; do
cat /sys/kernel/debug/usb/uvcvideo/2-6/clocks ;
done > ~/samples.log
3. Capture 100 frames.
yavta -c100 > yavta.log
4. Stop the "while true" with ctrl-C.
5. Capture the uvcvideo stats.
cat /sys/kernel/debug/usb/uvcvideo/2-6/stats > stats.log
6. Capture the kernel log.
dmesg > dmesg.log
7. Send me all the log files.
Done:
http://notaz.gp2x.de/tmp/c920_yavta/3/
--
Gražvydas
Hello,
I've reproduced this issue on a Logitech C920 in the following environments:
1. x86_64 Linux 3.19.3 (Gentoo, custom kernel)
2. x86_64 Linux 3.13.0-46-generic (Ubuntu)
3. armv7a Linux 3.19.3 (Arch Linux, custom kernel)
I can confirm that the issue is not present in Linux 3.8.y.
I'm not sure if there have been any developments in regards to this in
recent months, but I'm happy to help out in any way possible. If someone
is in need of new debug logs, I can follow the steps above and provide them.
--
Milos
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
