Thanks a lot, Hans. I know the reason that you use vm_iomap_memory() instead of remap_pfn_range(). But according to my analysis, the sanity check is not suitable for v4l2 buffers mapping. You can check the code logic to see this. Migration to vb2 is not a quick job and it is not on our schedule yet. I just need you to check the code logic and make a decision for this. Best regards, Fancy Fang -----Original Message----- From: Hans Verkuil [mailto:hverkuil@xxxxxxxxx] Sent: Tuesday, September 23, 2014 2:10 PM To: Fang Chen-B47543; m.chehab@xxxxxxxxxxx; viro@xxxxxxxxxxxxxxxxxx Cc: Guo Shawn-R65073; linux-media@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; Marek Szyprowski Subject: Re: [PATCH] [media] videobuf-dma-contig: replace vm_iomap_memory() with remap_pfn_range(). Hi Fancy Fang, I do have a few comments: 1) One reason why the switch to vm_iomap_memory() was made originally was that that function did a bunch of sanity checks. Since this patch moves back to remap_pfn_range() those sanity checks are lost and should be reinstated. 2) You need Marek's Ack as well since he understands the memory code much better than I do. 3) There are efforts underway to make a modern i.mx6 video driver based on vb2 and all the other modern V4L2 APIs, wouldn't it be much better if freescale jumps on board and starts working on that code as well? See e.g. this mail thread: http://www.spinics.net/lists/linux-media/msg79078.html I assume this refers to the same hardware. The official freescale driver for that hardware is horrendous. If you are writing code for unrelated hardware, then you should move over to vb2 yourself. videobuf should not be used anymore for new drivers. 4) I still do not entirely understand the control flow and I will have to take another look. I'll see if I can do that tomorrow. Regards, Hans On 09/23/2014 05:11 AM, chen.fang@xxxxxxxxxxxxx wrote: > Hans, > Do you have any more comment on this patch? > > Best regards, > Fancy Fang > > -----Original Message----- > From: Fang Chen-B47543 > Sent: Wednesday, September 10, 2014 3:29 PM > To: 'Hans Verkuil'; m.chehab@xxxxxxxxxxx; viro@xxxxxxxxxxxxxxxxxx > Cc: Guo Shawn-R65073; linux-media@xxxxxxxxxxxxxxx; > linux-kernel@xxxxxxxxxxxxxxx; Marek Szyprowski > Subject: RE: [PATCH] [media] videobuf-dma-contig: replace vm_iomap_memory() with remap_pfn_range(). > > On the Freescale imx6 platform which belongs to ARM architecture. The driver is our local v4l2 output driver which is not upstream yet unfortunately. > > Best regards, > Fancy Fang > > -----Original Message----- > From: Hans Verkuil [mailto:hverkuil@xxxxxxxxx] > Sent: Wednesday, September 10, 2014 3:21 PM > To: Fang Chen-B47543; m.chehab@xxxxxxxxxxx; viro@xxxxxxxxxxxxxxxxxx > Cc: Guo Shawn-R65073; linux-media@xxxxxxxxxxxxxxx; > linux-kernel@xxxxxxxxxxxxxxx; Marek Szyprowski > Subject: Re: [PATCH] [media] videobuf-dma-contig: replace vm_iomap_memory() with remap_pfn_range(). > > On 09/10/14 09:14, chen.fang@xxxxxxxxxxxxx wrote: >> It is not a theoretically issue, it is a real case that the mapping failed issue happens in 3.14.y kernel but not happens in previous 3.10.y kernel. >> So I need your confirmation on it. > > With which driver does this happen? On which architecture? > > Regards, > > Hans > >> >> Thanks. >> >> Best regards, >> Fancy Fang >> >> -----Original Message----- >> From: Hans Verkuil [mailto:hverkuil@xxxxxxxxx] >> Sent: Wednesday, September 10, 2014 3:01 PM >> To: Fang Chen-B47543; m.chehab@xxxxxxxxxxx; viro@xxxxxxxxxxxxxxxxxx >> Cc: Guo Shawn-R65073; linux-media@xxxxxxxxxxxxxxx; >> linux-kernel@xxxxxxxxxxxxxxx; Marek Szyprowski >> Subject: Re: [PATCH] [media] videobuf-dma-contig: replace vm_iomap_memory() with remap_pfn_range(). >> >> On 09/10/14 07:28, Fancy Fang wrote: >>> When user requests V4L2_MEMORY_MMAP type buffers, the videobuf-core >>> will assign the corresponding offset to the 'boff' field of the >>> videobuf_buffer for each requested buffer sequentially. Later, user >>> may call mmap() to map one or all of the buffers with the 'offset' >>> parameter which is equal to its 'boff' value. Obviously, the 'offset' >>> value is only used to find the matched buffer instead of to be the >>> real offset from the buffer's physical start address as used by >>> vm_iomap_memory(). So, in some case that if the offset is not zero, >>> vm_iomap_memory() will fail. >> >> Is this just a fix for something that can fail theoretically, or do you actually have a case where this happens? I am very reluctant to make any changes to videobuf. Drivers should all migrate to vb2. >> >> I have CC-ed Marek as well since he knows a lot more about this stuff than I do. >> >> Regards, >> >> Hans >> >>> >>> Signed-off-by: Fancy Fang <chen.fang@xxxxxxxxxxxxx> >>> --- >>> drivers/media/v4l2-core/videobuf-dma-contig.c | 4 +++- >>> 1 file changed, 3 insertions(+), 1 deletion(-) >>> >>> diff --git a/drivers/media/v4l2-core/videobuf-dma-contig.c >>> b/drivers/media/v4l2-core/videobuf-dma-contig.c >>> index bf80f0f..8bd9889 100644 >>> --- a/drivers/media/v4l2-core/videobuf-dma-contig.c >>> +++ b/drivers/media/v4l2-core/videobuf-dma-contig.c >>> @@ -305,7 +305,9 @@ static int __videobuf_mmap_mapper(struct videobuf_queue *q, >>> /* Try to remap memory */ >>> size = vma->vm_end - vma->vm_start; >>> vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot); >>> - retval = vm_iomap_memory(vma, mem->dma_handle, size); >>> + retval = remap_pfn_range(vma, vma->vm_start, >>> + mem->dma_handle >> PAGE_SHIFT, >>> + size, vma->vm_page_prot); >>> if (retval) { >>> dev_err(q->dev, "mmap: remap failed with error %d. ", >>> retval); >>> >> > -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
