I have the same card, and have not much problems. I have some reception
issues, but I don't think it's to blame on the card (yet). I do use
tvheadend however.
In anycase, can you use w_scan or dvb-scan?
On 06-03-13 14:27, Jean Delvare wrote:
Hi all,
I have a TerraTec Cinergy T PCIe Dual card and I can't get it to work.
I had been using it several months ago, with some success, although the
stability wasn't ideal. Then I moved it to another machine to check if
it was any better on Windows (and indeed it was better.) Now I put it
back in my system and I can't get it to work at all.
I have the following relevant kernel log messages:
[ 0.362783] pci 0000:0b:00.0: [14f1:8852] type 00 class 0x040000
[ 0.362809] pci 0000:0b:00.0: reg 10: [mem 0xfbc00000-0xfbdfffff 64bit]
[ 0.362940] pci 0000:0b:00.0: supports D1 D2
[ 0.362942] pci 0000:0b:00.0: PME# supported from D0 D1 D2 D3hot
[ 0.362967] pci 0000:0b:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 6.313259] cx23885 driver version 0.0.3 loaded
[ 6.313898] CORE cx23885[0]: subsystem: 153b:117e, board: TerraTec Cinergy T PCIe Dual [card=34,autodetected]
[ 6.498999] cx25840 11-0044: cx23885 A/V decoder found @ 0x88 (cx23885[0])
[ 7.114399] cx25840 11-0044: loaded v4l-cx23885-avcore-01.fw firmware (16382 bytes)
[ 7.150641] cx23885_dvb_register() allocating 1 frontend(s)
[ 7.150704] cx23885[0]: cx23885 based dvb card
[ 7.178681] drxk: status = 0x639160d9
[ 7.180049] drxk: detected a drx-3916k, spin A3, xtal 20.250 MHz
[ 7.245259] DRXK driver version 0.9.4300
[ 7.268760] drxk: frontend initialized.
[ 7.961207] mt2063_attach: Attaching MT2063
[ 7.961271] DVB: registering new adapter (cx23885[0])
[ 7.961332] DVB: registering adapter 0 frontend 0 (DRXK DVB-T)...
[ 7.961877] cx23885_dvb_register() allocating 1 frontend(s)
[ 7.961881] cx23885[0]: cx23885 based dvb card
[ 7.974320] drxk: status = 0x639130d9
[ 7.975838] drxk: detected a drx-3913k, spin A3, xtal 20.250 MHz
[ 8.040888] DRXK driver version 0.9.4300
[ 8.064459] drxk: frontend initialized.
[ 8.064467] mt2063_attach: Attaching MT2063
[ 8.064475] DVB: registering new adapter (cx23885[0])
[ 8.064482] DVB: registering adapter 1 frontend 0 (DRXK DVB-C DVB-T)...
[ 8.065919] cx23885_dev_checkrevision() Hardware revision = 0xa5
[ 8.066004] cx23885[0]/0: found at 0000:0b:00.0, rev: 4, irq: 28, latency: 0, mmio: 0xfbc00000
[ 27.281490] mt2063: detected a mt2063 B3
[ 27.319390] mt2063: detected a mt2063 B3
I don't see anything wrong here, all the components are apparently
found and identified properly. However I can't get the card to actually
work, neither in me-tv nor in VLC.
Me-tv (version 1.3.6) tells me:
03/06/13 14:20:10: Device: 'DRXK DVB-T' (DVB-T) at "/dev/dvb/adapter0/frontend0"
03/06/13 14:20:11: Device: 'DRXK DVB-C DVB-T' (DVB-C) at "/dev/dvb/adapter1/frontend0"
03/06/13 14:20:11: Frontend::tune_to(490000000)
03/06/13 14:20:11: Waiting for signal lock ...
And then "Failed to lock channel".
VLC (version 2.0.5) tells me:
main stream error: cannot pre fill buffer
I tried with kernels 3.4.30, 3.5.7, 3.6.0, 3.6.11, 3.7.10 and 3.8.2, with
exactly the same results.
How would I debug this further?
Thanks,
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
