On 01/12/2013 01:45 AM, Jose Alberto Reguero wrote:
On Viernes, 11 de enero de 2013 20:38:01 Antti Palosaari escribió:
Hello Jose and Gianluca
Could you test that (tda18218 & mxl5007t):
http://git.linuxtv.org/anttip/media_tree.git/shortlog/refs/heads/it9135_tune
r
I wonder if ADC config logic still works for superheterodyne tuners
(tuner having IF). I changed it to adc / 2 always due to IT9135 tuner.
That makes me wonder it possible breaks tuners having IF, as ADC was
clocked just over 20MHz and if it is half then it is 10MHz. For BB that
is enough, but I think that having IF, which is 4MHz at least for 8MHz
BW it is too less.
F*ck I hate to maintain driver without a hardware! Any idea where I can
get AF9035 device having tda18218 or mxl5007t?
regards
Antti
Still pending the changes for mxl5007t. Attached is a patch for that.
Changes to make work Avermedia Twinstar with the af9035 driver.
Signed-off-by: Jose Alberto Reguero <jareguero@xxxxxxxxxxxxxx>
I cannot do much about this as it changes mxl5007t driver which is not
maintained by me. :)
regards
Antti
Jose Alberto
diff -upr linux/drivers/media/tuners/mxl5007t.c
linux.new/drivers/media/tuners/mxl5007t.c
--- linux/drivers/media/tuners/mxl5007t.c 2012-08-14 05:45:22.000000000 +0200
+++ linux.new/drivers/media/tuners/mxl5007t.c 2013-01-10 19:23:09.247556275
+0100
@@ -374,7 +374,6 @@ static struct reg_pair_t *mxl5007t_calc_
mxl5007t_set_if_freq_bits(state, cfg->if_freq_hz, cfg->invert_if);
mxl5007t_set_xtal_freq_bits(state, cfg->xtal_freq_hz);
- set_reg_bits(state->tab_init, 0x04, 0x01, cfg->loop_thru_enable);
set_reg_bits(state->tab_init, 0x03, 0x08, cfg->clk_out_enable << 3);
set_reg_bits(state->tab_init, 0x03, 0x07, cfg->clk_out_amp);
@@ -531,9 +530,12 @@ static int mxl5007t_tuner_init(struct mx
struct reg_pair_t *init_regs;
int ret;
- ret = mxl5007t_soft_reset(state);
- if (mxl_fail(ret))
+ if (!state->config->no_reset) {
+ ret = mxl5007t_soft_reset(state);
+ if (mxl_fail(ret))
goto fail;
+ }
+
/* calculate initialization reg array */
init_regs = mxl5007t_calc_init_regs(state, mode);
@@ -887,7 +889,12 @@ struct dvb_frontend *mxl5007t_attach(str
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 1);
- ret = mxl5007t_get_chip_id(state);
+ if (!state->config->no_probe)
+ ret = mxl5007t_get_chip_id(state);
+
+ ret = mxl5007t_write_reg(state, 0x04,
+ state->config->loop_thru_enable);
+
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 0);
diff -upr linux/drivers/media/tuners/mxl5007t.h
linux.new/drivers/media/tuners/mxl5007t.h
--- linux/drivers/media/tuners/mxl5007t.h 2012-08-14 05:45:22.000000000 +0200
+++ linux.new/drivers/media/tuners/mxl5007t.h 2013-01-10 19:19:11.204379581
+0100
@@ -73,8 +73,10 @@ struct mxl5007t_config {
enum mxl5007t_xtal_freq xtal_freq_hz;
enum mxl5007t_if_freq if_freq_hz;
unsigned int invert_if:1;
- unsigned int loop_thru_enable:1;
+ unsigned int loop_thru_enable:3;
unsigned int clk_out_enable:1;
+ unsigned int no_probe:1;
+ unsigned int no_reset:1;
};
#if defined(CONFIG_MEDIA_TUNER_MXL5007T) ||
(defined(CONFIG_MEDIA_TUNER_MXL5007T_MODULE) && defined(MODULE))
diff -upr linux/drivers/media/usb/dvb-usb-v2/af9035.c
linux.new/drivers/media/usb/dvb-usb-v2/af9035.c
--- linux/drivers/media/usb/dvb-usb-v2/af9035.c 2013-01-07 05:45:57.000000000
+0100
+++ linux.new/drivers/media/usb/dvb-usb-v2/af9035.c 2013-01-12
00:30:57.557310465 +0100
@@ -886,13 +886,17 @@ static struct mxl5007t_config af9035_mxl
.loop_thru_enable = 0,
.clk_out_enable = 0,
.clk_out_amp = MxL_CLKOUT_AMP_0_94V,
+ .no_probe = 1,
+ .no_reset = 1,
}, {
.xtal_freq_hz = MxL_XTAL_24_MHZ,
.if_freq_hz = MxL_IF_4_57_MHZ,
.invert_if = 0,
- .loop_thru_enable = 1,
+ .loop_thru_enable = 3,
.clk_out_enable = 1,
.clk_out_amp = MxL_CLKOUT_AMP_0_94V,
+ .no_probe = 1,
+ .no_reset = 1,
}
};
--
http://palosaari.fi/
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
