On 17-09-12 10:25, Oliver Schinagl wrote:
On 17-09-12 01:36, Antti Palosaari wrote:
On 09/17/2012 01:10 AM, Oliver Schinagl wrote:
On 09/16/12 19:25, Antti Palosaari wrote:
On 09/16/2012 06:03 PM, Oliver Schinagl wrote:
I don't have windows, so capturing using windows is near impossible.
Also since the vendor driver used to work, I guess I will have to dig
into that more.
You could capture data from Linux too (eg. Wireshark).
Ah of course. I'll dig up the old vendor driver and see if I can get it
running on 3.2 or better yet, on 3.5/your-3.6. I know there's patches
for 3.2 but I've never tested those. Otherwise the older 2.6.2* series
should still work.
But with a little experience you could see those GPIOs reading
existing
Linux driver and then do some tests to see what happens. For example
some GPIO powers tuner off, you will see I2C error. Changing it back
error disappears.
I have zero experience so I'll try to figure things out. I guess you
currently turn on/off GPIO's etc in the current driver? Any line which
does this so I can examine how it's done? As for the I2C errors, I
suppose the current driver will spew those out?
Those GPIOs are set in file af9035.c, functiuons:
af9035_tuner_attach() and af9035_fc0011_tuner_callback(). For
TDA18218 tuner there is no any GPIOs set, which could be wrong and it
just works with good luck OR it is wired/connected directly so that
GPIOs are not used at all.
Ahah! Then I know what to look for. Since af9035 also has fc0011
support, there should be some similarities I can find.
Which I did. I found that the af9033 sets the "gpiot2" o, en and on
values high to enable the tuner. Luckly, the fc2580 is routed to the
exact same gpio and thus the same tuner enable/disable routine can be
used as the FC0011. Appearantly the FC0011 tuner also has a led that
needs to be enabled/disabled, at gpioh8, which the fc2580 lacks. So I
found the tuner enable and should be able to incorporate that without issue.
The other callback the fc2580 has, is a 'reset'. The fc2580 appears to
be lacking such feature, or is not used in the vendor driver.
Speaking off, in my previous message, I wrote about the driver spitting
out the following error:
[dvb_usb_af9035]af9035_read_config =_ "%s: [%d]tuner=%02x\012"
It is the tuner ID value got from eeprom. You should take that number
and add it to af9033.h file:
#define AF9033_TUNER_FC2580 0xXXXX <= insert number here
Yes, but I think %s, %d and %02x\012 should actually list values?
(\012 I belive is \newline)
I need to learn dynamic_debug; and I think I may have set it up wrong
last time (af9035 and fc2580, but not af9033). I found some good
documentation and will try this tonight.
None of the values where set however. Did I miss-configure anything for
it to cause to 'forget' substituting?
What you mean? Could you enable debugs, plug stick in and copy paste
what debugs says?
I have dynamic debugging enabled and have gotten the above snipped
from the proc/sysfs interface. Also dmesg from replugging I've
attached a few messages back.
[ 188.051502] af9033: firmware version: LINK=12.13.15.0 OFDM=6.20.15.0
[ 188.051520] usb 1-3: DVB: registering adapter 0 frontend 0 (Afatech
AF9033 (DVB-T))...
[ 188.054019] i2c i2c-1: fc2580_attach: chip_id=5a
[ 188.054030] i2c i2c-1: fc2580_attach: failed=0
[ 188.054471] i2c i2c-1: fc2580_release:
[ 188.054485] usb 1-3: dvb_usbv2: 'Asus U3100Mini Plus' error while
loading driver (-19)
is the dmesg output from then, which doesn't list the values from the
debugging bit either. I suppose I need more debugging options enabled
to have those flag characters actually filled in?
Since all the pieces should be there, fc2580 driver, af9033/5 driver,
it's just a matter of glueing things together, right? I'll dig
further
into it and see what I can find/do.
Correct. Tuner init (demod settings fc2580) for is needed for af9033.
And GPIOs for AF9035. In very bad luck some changes for fc2580 is
needed
too, but it is not very, very, unlikely.
This patch is very similar you will need to do (tda18218 tuner support
for af9035):
http://patchwork.linuxtv.org/patch/10547/
I re-did my patch using that as a template (before I used your work on
the rtl) and got the exact result.
Your rtl|fc2580 combo btw (from bare memory) didn't have the
fc2580_init
stream in af9033_priv.h. What exactly gets init-ed there? The af9033 to
work with the fc2580?
You have to add fc2580 init table to file af9033_priv.h. It
configures all the settings needed for AF9033 demod in order to
operate with FC2580 tuner. There is some values like "tuner ID" which
is passed for AF9033 firmware, dunno what kind of tweaks it done.
Maybe calculates some values like signal strengths and AGC values. It
could work without, but at least performance is reduced.
I did add it. I found the init tables in the vendor driver, compared
them to the existing init tables, found that the others where
identical, but offset by 0x8000. I thus copied the table for the
fc2580 and added the address offset.
You can glance over it in the driver patch I submitted last week,
should be there :)
But since it modified the AF9033, I understand why your rtl driver
didn't have the init table for the fc2580.
regards
Antti
Thanks,
Oliver
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
