Re: [beagleboard] [RFC v1] mt9v113: VGA camera sensor driver and support for BeagleBoard

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Jul 25, 2011 at 10:13 AM, Koen Kooi <koen@xxxxxxxxxxxxxxx> wrote:
>
> Op 25 jul. 2011, om 18:56 heeft Mark Grosen het volgende geschreven:
>
>> On Wed, Jul 13, 2011 at 11:22 AM, Joel A Fernandes <agnel.joel@xxxxxxxxx> wrote:
>>> * Adds support for mt9v113 sensor by borrowing heavily from PSP 2.6.37 kernel patches
>>> * Adapted to changes in v4l2 framework and ISP driver
>>>
>>> Signed-off-by: Joel A Fernandes <agnel.joel@xxxxxxxxx>
>>> ---
>>> This patch will apply against the 2.6.39 kernel built from the OE-development tree (Which is essentially
>>> the v2.6.39 from the main tree with OE patches for BeagleBoard support and a few other features)
>>>
>>> If you have the Leapord imaging camera board with this particular sensor, I would apprecite it if anyone could
>>> try this patch out and provide any feedback/test results.
>>>
>>> To get the complete tree which works on a BeagleBoard-xM with all the OE patches and this patch,
>>> you can clone: https://github.com/joelagnel/linux-omap-2.6/tree/oedev-2.6.39-mt9v113
>>>
>>> It will compile and work on a BeagleBoard-xM with the defconfig at:
>>> http://cgit.openembedded.org/cgit.cgi/openembedded/tree/recipes/linux/linux-omap-2.6.39/beagleboard/defconfig
>>>
>>> Also you will need to apply my media-ctl patch (or clone the tree) to setup the formats:
>>> https://github.com/joelagnel/media-ctl/commit/cdf24d1249ac1ff3cd6f70ad80c3b76ac28ba0d5
>>>
>>> Binaries for quick testing on a BeagleBoard-xM:
>>> U-boot: http://utdallas.edu/~joel.fernandes/u-boot.bin
>>> U-boot: http://utdallas.edu/~joel.fernandes/MLO
>>> uEnv.txt: http://utdallas.edu/~joel.fernandes/uEnv.txt
>>> media-ctl: http://utdallas.edu/~joel.fernandes/media-ctl
>>> kernel: http://utdallas.edu/~joel.fernandes/uImage
>>>
>>> media-ctl/yavta commands you could use to get it to show a picture can be found at:
>>> http://utdallas.edu/~joel.fernandes/stream.sh
>>>
>>
>> Joel,
>>
>> I gave this a try this weekend. I ran into a few problems/questions.
>>
>> I wanted to try with pre-built (tested?) binaries so I grabbed yours
>> (used your uImage):
>> 1. media-ctl binary does not work because there is no libmediactl.so
>> on my Angstrom root FS.
>> 2. There was no yavta-nc application.
>
> have you tried 'opkg update ; opkg install mediactl yavta-nc' ?
>

Showing my Angstrom ignorance here, but I cannot get these packages
via opkg update. I use Narcissus builder - I built a new FS yesterday
using 2011.03 - should I have used "next". It runs fine, but when I do
the opkg update; opkg install yavta-nc  it fails. I see media-ctl and
yavta-nc in the package browser website, but my guess is they are for
"newer" builds?

Mark
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux