I was wondering if someone might be able to figure out whatâs wrong with my HVR-950q. When I can get it to work, it works just fine, but it seems that after a restart in Ubuntu 10.10 x64 it wonât work for quite a while (unable to determine how long specifically, but in the realm of hours to days). It will work fine under windows after multiple reboots, so Iâm wondering if the linux firmware isnât unloading properly or something. When I start up mythtv again I get the following info from dmesg: [ 22.832293] xc5000: xc5000_init() [ 22.837041] xc5000: xc5000_is_firmware_loaded() returns False id = 0Ã2000 [ 22.837044] xc5000: waiting for firmware upload (dvb-fe-xc5000-1.6.114.fw)â [ 22.865012] xc5000: firmware read 12401 bytes. [ 22.865015] xc5000: firmware uploadingâ [ 22.865019] xc5000: xc5000_TunerReset() [ 27.440072] 8:2:1: endpoint lacks sample rate attribute bit, cannot set. [ 27.461883] 8:2:1: endpoint lacks sample rate attribute bit, cannot set. [ 27.487738] 8:2:1: endpoint lacks sample rate attribute bit, cannot set. [ 31.671477] xc5000: firmware upload completeâ [ 31.671493] xc5000: xc_initialize() [ 36.074720] xc5000: *** ADC envelope (0-1023) = 65535 [ 36.079462] xc5000: *** Frequency error = 1023984 Hz [ 36.084462] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 65535 [ 36.094082] xc5000: *** HW: V0f.0f, FW: V0f.0f.ffff [ 36.098826] xc5000: *** Horizontal sync frequency = 31244 Hz [ 36.103575] xc5000: *** Frame lines = 65535 [ 36.108319] xc5000: *** Quality (0:56dB) = 65535 [ 36.427140] xc5000: xc5000_is_firmware_loaded() returns True id = 0xffff [ 36.427147] xc5000: xc5000_set_params() frequency=629000000 (Hz) [ 36.427151] xc5000: xc5000_set_params() ATSC [ 36.427154] xc5000: xc5000_set_params() VSB modulation [ 36.427158] xc5000: xc5000_set_params() frequency=627250000 (compensated) [ 36.427162] xc5000: xc_SetSignalSource(0) Source = ANTENNA [ 38.510023] xc5000: xc_SetTVStandard(0Ã8002,0x00c0) [ 38.510029] xc5000: xc_SetTVStandard() Standard = DTV6 [ 42.900024] xc5000: xc_set_IF_frequency(freq_khz = 6000) freq_code = 0Ã1800 [ 45.130023] xc5000: xc_tune_channel(627250000) [ 45.130028] xc5000: xc_set_RF_frequency(627250000) [ 47.334695] xc5000: *** ADC envelope (0-1023) = 65535 [ 47.339438] xc5000: *** Frequency error = 1023984 Hz [ 47.344186] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 65535 [ 47.353683] xc5000: *** HW: V0f.0f, FW: V0f.0f.ffff [ 47.358427] xc5000: *** Horizontal sync frequency = 31244 Hz [ 47.363175] xc5000: *** Frame lines = 65535 [ 47.367921] xc5000: *** Quality (0:56dB) = 65535 When the card does work right the line "[ 47.344186] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 65535" doesn't end with 65535 (can't remember exactly what cause it's been a little while since I've fiddled with this. Since it's 65535 that makes me wonder if it's some sort of overflow or something. Any help would be greatly appreciated! -Kyle -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
