Fist of all, I would thank you about your work. I have done a test again and it seems to work with your last change. I didn't found any major issue. 14:14 root@telstar /home/lboue # modprobe ngene one_adapter=0 debug=1 [ 584.013474] nGene PCIE bridge driver, Copyright (C) 2005-2007 Micronas [ 584.013495] ngene 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 584.013503] ngene: Found Mystique SaTiX-S2 Dual (v2) [ 584.014226] ngene 0000:04:00.0: setting latency timer to 64 [ 584.014305] ngene: Device version 1 [ 584.014339] ngene 0000:04:00.0: firmware: requesting ngene_18.fw [ 584.016649] ngene: Loading firmware file ngene_18.fw. [ 584.027625] ngene 0000:04:00.0: irq 33 for MSI/MSI-X [ 584.029106] error in i2c_read_reg [ 584.029179] No CXD2099 detected at 40 [ 584.342566] LNBx2x attached on addr=a [ 584.342659] stv6110x_attach: Attaching STV6110x [ 584.342662] DVB: registering new adapter (nGene) [ 584.342667] DVB: registering adapter 0 frontend 0 (STV090x Multistandard)... [ 584.343681] LNBx2x attached on addr=8 [ 584.343774] stv6110x_attach: Attaching STV6110x [ 584.343777] DVB: registering new adapter (nGene) [ 584.343782] DVB: registering adapter 1 frontend 0 (STV090x Multistandard)... There is two adapters with one frontend into each: 14:06 lboue@telstar ~ % ls /dev/dvb/adapter0 demux0 dvr0 frontend0 net0 14:06 lboue@telstar ~ % ls /dev/dvb/adapter1 demux0 dvr0 frontend0 net0 14:12 root@telstar /home/lboue # modprobe ngene one_adapter=1 [ 403.560150] nGene PCIE bridge driver, Copyright (C) 2005-2007 Micronas [ 403.560169] ngene 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 403.560177] ngene: Found Mystique SaTiX-S2 Dual (v2) [ 403.560873] ngene 0000:04:00.0: setting latency timer to 64 [ 403.560952] ngene: Device version 1 [ 403.560963] ngene 0000:04:00.0: firmware: requesting ngene_18.fw [ 403.563416] ngene: Loading firmware file ngene_18.fw. [ 403.574393] ngene 0000:04:00.0: irq 33 for MSI/MSI-X [ 403.575874] error in i2c_read_reg [ 403.575948] No CXD2099 detected at 40 [ 403.893231] LNBx2x attached on addr=a [ 403.893323] stv6110x_attach: Attaching STV6110x [ 403.893327] DVB: registering new adapter (nGene) [ 403.893332] DVB: registering adapter 0 frontend 0 (STV090x Multistandard)... [ 403.894359] LNBx2x attached on addr=8 [ 403.894451] stv6110x_attach: Attaching STV6110x [ 403.894456] DVB: registering adapter 0 frontend 0 (STV090x Multistandard)... 14:13 root@telstar /home/lboue # ls /dev/dvb/adapter0/ demux0 demux1 dvr0 dvr1 frontend0 frontend1 net0 net1 The is only the needed adapters but I think there is a errror about the frontend number. It should be DVB: registering adapter 0 frontend 1 (STV090x Multistandard) instead of: DVB: registering adapter 0 frontend 0 (STV090x Multistandard) Best Regards Le 28/12/2010 08:57, Oliver Endriss a écrit : > On Monday 27 December 2010 22:49:51 Oliver Endriss wrote: >> On Sunday 26 December 2010 15:40:15 Ludovic BOUÉ wrote: >>> Hi all, >>> >>> I have a Satix-S2 Dual and I'm trying to get to work without his CI in a first time. I'm trying ngene-test2 >>> from http://linuxtv.org/hg/~endriss/ngene-test2/ under >>> 2.6.32-21-generic. >>> >>> It contains too much nodes (extra demuxes, dvrs & nets): >>> ... >>> Is it connected to this commit (http://linuxtv.org/hg/~endriss/ngene-test2/rev/eb4142f0d0ac) about "Support up to 4 tuners for cineS2 v5, duoflex & mystique v2" ? >> Yes. >> >> Please note that this is an experimental repository. >> This bug will be fixed before the code will be submitted upstream. >> (It is more complicated that it might appear at the first glance.) > Meanwhile I reworked channel initialisation and shutdown, > and the device nodes should be correct for all configurations. > > Please re-test and report any remaining problems. > > CU > Oliver > -- Ludovic BOUÉ -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
