The mode field of the imx219 structure is only used in
imx219_init_controls(), after the probe function sets it to point to the
default mode. Use the default mode directly when initializing controls,
and drop the mode field from the imx219 structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
Reviewed-by: Jacopo Mondi <jacopo.mondi@xxxxxxxxxxxxxxxx>
Reviewed-by: Dave Stevenson <dave.stevenson@xxxxxxxxxxxxxxx>
---
drivers/media/i2c/imx219.c | 20 +++++++-------------
1 file changed, 7 insertions(+), 13 deletions(-)
diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c
index f4f684bda4fa..82e5d1dad14a 100644
--- a/drivers/media/i2c/imx219.c
+++ b/drivers/media/i2c/imx219.c
@@ -362,9 +362,6 @@ struct imx219 {
struct v4l2_ctrl *vblank;
struct v4l2_ctrl *hblank;
- /* Current mode */
- const struct imx219_mode *mode;
-
/* Two or Four lanes */
u8 lanes;
};
@@ -580,7 +577,6 @@ static int imx219_set_pad_format(struct v4l2_subdev *sd,
*crop = mode->crop;
if (fmt->which == V4L2_SUBDEV_FORMAT_ACTIVE) {
- imx219->mode = mode;
/* Update limits and set FPS to default */
__v4l2_ctrl_modify_range(imx219->vblank, IMX219_VBLANK_MIN,
IMX219_VTS_MAX - mode->height, 1,
@@ -923,8 +919,8 @@ static unsigned long imx219_get_pixel_rate(struct imx219 *imx219)
static int imx219_init_controls(struct imx219 *imx219)
{
struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
+ const struct imx219_mode *mode = &supported_modes[0];
struct v4l2_ctrl_handler *ctrl_hdlr;
- unsigned int height = imx219->mode->height;
struct v4l2_fwnode_device_properties props;
int exposure_max, exposure_def, hblank;
int i, ret;
@@ -953,15 +949,15 @@ static int imx219_init_controls(struct imx219 *imx219)
/* Initial vblank/hblank/exposure parameters based on current mode */
imx219->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops,
V4L2_CID_VBLANK, IMX219_VBLANK_MIN,
- IMX219_VTS_MAX - height, 1,
- imx219->mode->vts_def - height);
- hblank = IMX219_PPL_DEFAULT - imx219->mode->width;
+ IMX219_VTS_MAX - mode->height, 1,
+ mode->vts_def - mode->height);
+ hblank = IMX219_PPL_DEFAULT - mode->width;
imx219->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops,
V4L2_CID_HBLANK, hblank, hblank,
1, hblank);
if (imx219->hblank)
imx219->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
- exposure_max = imx219->mode->vts_def - 4;
+ exposure_max = mode->vts_def - 4;
exposure_def = (exposure_max < IMX219_EXPOSURE_DEFAULT) ?
exposure_max : IMX219_EXPOSURE_DEFAULT;
imx219->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops,
@@ -1148,10 +1144,8 @@ static int imx219_probe(struct i2c_client *client)
if (ret)
goto error_power_off;
- /* Set default mode to max resolution */
- imx219->mode = &supported_modes[0];
-
- /* sensor doesn't enter LP-11 state upon power up until and unless
+ /*
+ * Sensor doesn't enter LP-11 state upon power up until and unless
* streaming is started, so upon power up switch the modes to:
* streaming -> standby
*/
--
Regards,
Laurent Pinchart
