Re: [RESEND PATCH v3] mtd: rawnand: macronix: OTP access for MX30LFxG18AC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Arseniy,

avkrasnov@xxxxxxxxxxxxxx wrote on Mon, 15 May 2023 12:49:50 +0300:

> Hello @Miquel!
> 
> Sorry, but who could review this patch? :) IIUC this logic is very hw specific and we need
> someone who knows it well? I tested this patch on our devices (with already known Meson NAND
> controller).

+ Jaime, who might test

> 
> Thanks, Arseniy
> 
> On 11.05.2023 21:21, Arseniy Krasnov wrote:
> > Cc: Mason Yang <masonccyang@xxxxxxxxxxx> and Boris Brezillon <boris.brezillon@xxxxxxxxxxxxx>
> > 
> > On 11.05.2023 18:21, Arseniy Krasnov wrote:  
> >> This adds support for OTP area access on MX30LFxG18AC chip series.
> >>
> >> Changelog:
> >>   v1 -> v2:
> >>   * Add slab.h include due to kernel test robot error.
> >>   v2 -> v3:
> >>   * Use 'uint64_t' as input argument for 'do_div()' instead
> >>     of 'unsigned long' due to kernel test robot error.
> >>
> >> Signed-off-by: Arseniy Krasnov <AVKrasnov@xxxxxxxxxxxxxx>
> >> ---
> >>  drivers/mtd/nand/raw/nand_macronix.c | 213 +++++++++++++++++++++++++++
> >>  1 file changed, 213 insertions(+)
> >>
> >> diff --git a/drivers/mtd/nand/raw/nand_macronix.c b/drivers/mtd/nand/raw/nand_macronix.c
> >> index 1472f925f386..2301f990678e 100644
> >> --- a/drivers/mtd/nand/raw/nand_macronix.c
> >> +++ b/drivers/mtd/nand/raw/nand_macronix.c
> >> @@ -6,6 +6,7 @@
> >>   * Author: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx>
> >>   */
> >>  
> >> +#include <linux/slab.h>
> >>  #include "linux/delay.h"
> >>  #include "internals.h"
> >>  
> >> @@ -31,6 +32,20 @@
> >>  
> >>  #define MXIC_CMD_POWER_DOWN 0xB9
> >>  
> >> +#define ONFI_FEATURE_ADDR_30LFXG18AC_OTP	0x90
> >> +#define MACRONIX_30LFXG18AC_OTP_START_PAGE	0
> >> +#define MACRONIX_30LFXG18AC_OTP_PAGES		30
> >> +#define MACRONIX_30LFXG18AC_OTP_PAGE_SIZE	2112
> >> +#define MACRONIX_30LFXG18AC_OTP_START_BYTE	\
> >> +	(MACRONIX_30LFXG18AC_OTP_START_PAGE *	\
> >> +	 MACRONIX_30LFXG18AC_OTP_PAGE_SIZE)
> >> +#define MACRONIX_30LFXG18AC_OTP_SIZE_BYTES	\
> >> +	(MACRONIX_30LFXG18AC_OTP_PAGES *	\
> >> +	 MACRONIX_30LFXG18AC_OTP_PAGE_SIZE)
> >> +
> >> +#define MACRONIX_30LFXG18AC_OTP_EN		BIT(0)
> >> +#define MACRONIX_30LFXG18AC_OTP_LOCKED		BIT(1)
> >> +
> >>  struct nand_onfi_vendor_macronix {
> >>  	u8 reserved;
> >>  	u8 reliability_func;
> >> @@ -316,6 +331,203 @@ static void macronix_nand_deep_power_down_support(struct nand_chip *chip)
> >>  	chip->ops.resume = mxic_nand_resume;
> >>  }
> >>  
> >> +static int macronix_30lfxg18ac_get_otp_info(struct mtd_info *mtd, size_t len,
> >> +					    size_t *retlen,
> >> +					    struct otp_info *buf)
> >> +{
> >> +	if (len < sizeof(*buf))
> >> +		return -EINVAL;
> >> +
> >> +	/* Don't know how to check that OTP is locked. */

Jaime, any idea?

> >> +	buf->locked = 0;
> >> +	buf->start = MACRONIX_30LFXG18AC_OTP_START_BYTE;
> >> +	buf->length = MACRONIX_30LFXG18AC_OTP_SIZE_BYTES;
> >> +
> >> +	*retlen = sizeof(*buf);
> >> +
> >> +	return 0;
> >> +}
> >> +
> >> +static int macronix_30lfxg18ac_otp_enable(struct nand_chip *nand)
> >> +{
> >> +	uint8_t feature_buf[ONFI_SUBFEATURE_PARAM_LEN] = { 0 };
> >> +
> >> +	feature_buf[0] = MACRONIX_30LFXG18AC_OTP_EN;
> >> +	return nand_set_features(nand, ONFI_FEATURE_ADDR_30LFXG18AC_OTP,
> >> +				 feature_buf);
> >> +}
> >> +
> >> +static int macronix_30lfxg18ac_otp_disable(struct nand_chip *nand)
> >> +{
> >> +	uint8_t feature_buf[ONFI_SUBFEATURE_PARAM_LEN] = { 0 };
> >> +
> >> +	return nand_set_features(nand, ONFI_FEATURE_ADDR_30LFXG18AC_OTP,
> >> +				 feature_buf);
> >> +}
> >> +
> >> +static int __macronix_30lfxg18ac_rw_otp(struct mtd_info *mtd,
> >> +					loff_t offs_in_flash,
> >> +					size_t len, size_t *retlen,
> >> +					u_char *buf, bool write)
> >> +{
> >> +	struct nand_chip *nand;
> >> +	size_t bytes_handled;
> >> +	off_t offs_in_page;
> >> +	uint64_t page;
> >> +	void *dma_buf;
> >> +	int ret;
> >> +
> >> +	/* 'nand_prog/read_page_op()' may use 'buf' as DMA buffer,
> >> +	 * so allocate properly aligned memory for it. This is
> >> +	 * needed because cross page accesses may lead to unaligned
> >> +	 * buffer address for DMA.
> >> +	 */
> >> +	dma_buf = kmalloc(MACRONIX_30LFXG18AC_OTP_PAGE_SIZE, GFP_KERNEL);
> >> +	if (!dma_buf)
> >> +		return -ENOMEM;
> >> +
> >> +	nand = mtd_to_nand(mtd);
> >> +	nand_select_target(nand, 0);
> >> +
> >> +	ret = macronix_30lfxg18ac_otp_enable(nand);
> >> +	if (ret)
> >> +		goto out_otp;
> >> +
> >> +	page = offs_in_flash;
> >> +	/* 'page' will be result of division. */
> >> +	offs_in_page = do_div(page, MACRONIX_30LFXG18AC_OTP_PAGE_SIZE);
> >> +	bytes_handled = 0;
> >> +
> >> +	while (bytes_handled < len &&
> >> +	       page < MACRONIX_30LFXG18AC_OTP_PAGES) {
> >> +		size_t bytes_to_handle;
> >> +
> >> +		bytes_to_handle = min_t(size_t, len - bytes_handled,
> >> +					MACRONIX_30LFXG18AC_OTP_PAGE_SIZE -
> >> +					offs_in_page);
> >> +
> >> +		if (write) {
> >> +			memcpy(dma_buf, &buf[bytes_handled], bytes_to_handle);
> >> +			ret = nand_prog_page_op(nand, page, offs_in_page,
> >> +						dma_buf, bytes_to_handle);
> >> +		} else {
> >> +			ret = nand_read_page_op(nand, page, offs_in_page,
> >> +						dma_buf, bytes_to_handle);
> >> +			if (!ret)
> >> +				memcpy(&buf[bytes_handled], dma_buf,
> >> +				       bytes_to_handle);
> >> +		}
> >> +		if (ret)
> >> +			goto out_otp;
> >> +
> >> +		bytes_handled += bytes_to_handle;
> >> +		offs_in_page = 0;
> >> +		page++;
> >> +	}
> >> +
> >> +	*retlen = bytes_handled;
> >> +
> >> +out_otp:
> >> +	if (ret)
> >> +		dev_err(&mtd->dev, "failed to perform OTP IO: %i\n", ret);
> >> +
> >> +	ret = macronix_30lfxg18ac_otp_disable(nand);
> >> +	WARN(ret, "failed to leave OTP mode after %s\n",
> >> +	     write ? "write" : "read");

Let's avoid WARN() calls (none in this driver are relevant IMHO). Just a
dev_err() should be enough.

> >> +	nand_deselect_target(nand);
> >> +	kfree(dma_buf);
> >> +
> >> +	return ret;
> >> +}
> >> +
> >> +static int macronix_30lfxg18ac_write_otp(struct mtd_info *mtd, loff_t to,
> >> +					 size_t len, size_t *rlen,
> >> +					 const u_char *buf)
> >> +{
> >> +	return __macronix_30lfxg18ac_rw_otp(mtd, to, len, rlen, (u_char *)buf,
> >> +					    true);
> >> +}
> >> +
> >> +static int macronix_30lfxg18ac_read_otp(struct mtd_info *mtd, loff_t from,
> >> +					size_t len, size_t *rlen,
> >> +					u_char *buf)
> >> +{
> >> +	return __macronix_30lfxg18ac_rw_otp(mtd, from, len, rlen, buf, false);
> >> +}
> >> +
> >> +static int macronix_30lfxg18ac_lock_otp(struct mtd_info *mtd, loff_t from,
> >> +					size_t len)
> >> +{
> >> +	uint8_t feature_buf[ONFI_SUBFEATURE_PARAM_LEN] = { 0 };
> >> +	struct nand_chip *nand;
> >> +	int ret;
> >> +
> >> +	if (from != MACRONIX_30LFXG18AC_OTP_START_BYTE ||
> >> +	    len != MACRONIX_30LFXG18AC_OTP_SIZE_BYTES)
> >> +		return -EINVAL;
> >> +
> >> +	dev_dbg(&mtd->dev, "locking OTP\n");
> >> +
> >> +	nand = mtd_to_nand(mtd);
> >> +	nand_select_target(nand, 0);
> >> +
> >> +	feature_buf[0] = MACRONIX_30LFXG18AC_OTP_EN |
> >> +			 MACRONIX_30LFXG18AC_OTP_LOCKED;
> >> +	ret = nand_set_features(nand, ONFI_FEATURE_ADDR_30LFXG18AC_OTP,
> >> +				feature_buf);
> >> +	if (ret) {
> >> +		dev_err(&mtd->dev,
> >> +			"failed to lock OTP (set features): %i\n", ret);
> >> +		nand_deselect_target(nand);
> >> +		return ret;
> >> +	}
> >> +
> >> +	/* Do dummy page prog with zero address. */
> >> +	feature_buf[0] = 0;
> >> +	ret = nand_prog_page_op(nand, 0, 0, feature_buf, 1);
> >> +	if (ret)
> >> +		dev_err(&mtd->dev,
> >> +			"failed to lock OTP (page prog): %i\n", ret);
> >> +
> >> +	ret = macronix_30lfxg18ac_otp_disable(nand);
> >> +	WARN(ret, "failed to leave OTP mode after lock\n");
> >> +
> >> +	nand_deselect_target(nand);
> >> +
> >> +	return ret;
> >> +}
> >> +
> >> +static void macronix_nand_setup_otp(struct nand_chip *chip)
> >> +{
> >> +	static const char * const supported_otp_models[] = {
> >> +		"MX30LF1G18AC",
> >> +		"MX30LF2G18AC",
> >> +		"MX30LF4G18AC",
> >> +	};
> >> +	struct mtd_info *mtd;
> >> +
> >> +	if (!chip->parameters.supports_set_get_features)
> >> +		return;
> >> +
> >> +	if (match_string(supported_otp_models,
> >> +			 ARRAY_SIZE(supported_otp_models),
> >> +			 chip->parameters.model) < 0)
> >> +		return;

I would start by checking the model, then it's list of supported ops.

> >> +
> >> +	bitmap_set(chip->parameters.get_feature_list,
> >> +		   ONFI_FEATURE_ADDR_30LFXG18AC_OTP, 1);
> >> +	bitmap_set(chip->parameters.set_feature_list,
> >> +		   ONFI_FEATURE_ADDR_30LFXG18AC_OTP, 1);
> >> +
> >> +	mtd = nand_to_mtd(chip);
> >> +	mtd->_get_fact_prot_info = macronix_30lfxg18ac_get_otp_info;
> >> +	mtd->_read_fact_prot_reg = macronix_30lfxg18ac_read_otp;
> >> +	mtd->_get_user_prot_info = macronix_30lfxg18ac_get_otp_info;
> >> +	mtd->_read_user_prot_reg = macronix_30lfxg18ac_read_otp;
> >> +	mtd->_write_user_prot_reg = macronix_30lfxg18ac_write_otp;
> >> +	mtd->_lock_user_prot_reg = macronix_30lfxg18ac_lock_otp;
> >> +}
> >> +
> >>  static int macronix_nand_init(struct nand_chip *chip)
> >>  {
> >>  	if (nand_is_slc(chip))
> >> @@ -325,6 +537,7 @@ static int macronix_nand_init(struct nand_chip *chip)
> >>  	macronix_nand_onfi_init(chip);
> >>  	macronix_nand_block_protection_support(chip);
> >>  	macronix_nand_deep_power_down_support(chip);
> >> +	macronix_nand_setup_otp(chip);
> >>  
> >>  	return 0;
> >>  }  


Thanks,
Miquèl




[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux