On 12/11/2022 18:26, Bryan O'Donoghue wrote:
Move the dts data for the rb3 navigation mezzanine into its own dts file.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../sdm845-db845c-navigation-mezzanine.dts | 107 ++++++++++++++++++
arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 99 ----------------
3 files changed, 108 insertions(+), 99 deletions(-)
create mode 100644 arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index d534888bcfe52..70ce09bc63a33 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -131,6 +131,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r1.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c-navigation-mezzanine.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-lg-judyln.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-lg-judyp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts
new file mode 100644
index 0000000000000..7bd0a15c72657
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts
@@ -0,0 +1,107 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2022, Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include "sdm845-db845c.dts"
+
+&cci {
+ status = "okay";
+};
+
+&camss {
camss goes before cci alphabetically.
Konrad
+ vdda-phy-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l26a_1p2>;
+
+ status = "okay";
+
+ ports {
+ port@0 {
+ reg = <0>;
+ csiphy0_ep: endpoint {
+ data-lanes = <0 1 2 3>;
+ remote-endpoint = <&ov8856_ep>;
+ };
+ };
+ };
+};
+
+&cci_i2c0 {
+ camera@10 {
+ compatible = "ovti,ov8856";
+ reg = <0x10>;
+
+ /* CAM0_RST_N */
+ reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cam0_default>;
+
+ clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+ clock-names = "xvclk";
+ clock-frequency = <19200000>;
+
+ /*
+ * The &vreg_s4a_1p8 trace is powered on as a,
+ * so it is represented by a fixed regulator.
+ *
+ * The 2.8V vdda-supply and 1.2V vddd-supply regulators
+ * both have to be enabled through the power management
+ * gpios.
+ */
+ dovdd-supply = <&vreg_lvs1a_1p8>;
+ avdd-supply = <&cam0_avdd_2v8>;
+ dvdd-supply = <&cam0_dvdd_1v2>;
+
+ status = "okay";
+
+ port {
+ ov8856_ep: endpoint {
+ link-frequencies = /bits/ 64
+ <360000000 180000000>;
+ data-lanes = <1 2 3 4>;
+ remote-endpoint = <&csiphy0_ep>;
+ };
+ };
+ };
+};
+
+&cci_i2c1 {
+ camera@60 {
+ compatible = "ovti,ov7251";
+
+ /* I2C address as per ov7251.txt linux documentation */
+ reg = <0x60>;
+
+ /* CAM3_RST_N */
+ enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cam3_default>;
+
+ clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+ clock-names = "xclk";
+ clock-frequency = <24000000>;
+
+ /*
+ * The &vreg_s4a_1p8 trace always powered on.
+ *
+ * The 2.8V vdda-supply regulator is enabled when the
+ * vreg_s4a_1p8 trace is pulled high.
+ * It too is represented by a fixed regulator.
+ *
+ * No 1.2V vddd-supply regulator is used.
+ */
+ vdddo-supply = <&vreg_lvs1a_1p8>;
+ vdda-supply = <&cam3_avdd_2v8>;
+
+ status = "disabled";
+
+ port {
+ ov7251_ep: endpoint {
+ data-lanes = <0 1>;
+/* remote-endpoint = <&csiphy3_ep>; */
+ };
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
index 5da91c646c200..f41c6d600ea8c 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
@@ -1174,105 +1174,6 @@ &pm8998_gpio {
};
-&cci {
- status = "okay";
-};
-
-&camss {
- vdda-phy-supply = <&vreg_l1a_0p875>;
- vdda-pll-supply = <&vreg_l26a_1p2>;
-
- status = "okay";
-
- ports {
- port@0 {
- reg = <0>;
- csiphy0_ep: endpoint {
- data-lanes = <0 1 2 3>;
- remote-endpoint = <&ov8856_ep>;
- };
- };
- };
-};
-
-&cci_i2c0 {
- camera@10 {
- compatible = "ovti,ov8856";
- reg = <0x10>;
-
- /* CAM0_RST_N */
- reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&cam0_default>;
-
- clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
- clock-names = "xvclk";
- clock-frequency = <19200000>;
-
- /*
- * The &vreg_s4a_1p8 trace is powered on as a,
- * so it is represented by a fixed regulator.
- *
- * The 2.8V vdda-supply and 1.2V vddd-supply regulators
- * both have to be enabled through the power management
- * gpios.
- */
- dovdd-supply = <&vreg_lvs1a_1p8>;
- avdd-supply = <&cam0_avdd_2v8>;
- dvdd-supply = <&cam0_dvdd_1v2>;
-
- status = "okay";
-
- port {
- ov8856_ep: endpoint {
- link-frequencies = /bits/ 64
- <360000000 180000000>;
- data-lanes = <1 2 3 4>;
- remote-endpoint = <&csiphy0_ep>;
- };
- };
- };
-};
-
-&cci_i2c1 {
- camera@60 {
- compatible = "ovti,ov7251";
-
- /* I2C address as per ov7251.txt linux documentation */
- reg = <0x60>;
-
- /* CAM3_RST_N */
- enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&cam3_default>;
-
- clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
- clock-names = "xclk";
- clock-frequency = <24000000>;
-
- /*
- * The &vreg_s4a_1p8 trace always powered on.
- *
- * The 2.8V vdda-supply regulator is enabled when the
- * vreg_s4a_1p8 trace is pulled high.
- * It too is represented by a fixed regulator.
- *
- * No 1.2V vddd-supply regulator is used.
- */
- vdddo-supply = <&vreg_lvs1a_1p8>;
- vdda-supply = <&cam3_avdd_2v8>;
-
- status = "disabled";
-
- port {
- ov7251_ep: endpoint {
- data-lanes = <0 1>;
-/* remote-endpoint = <&csiphy3_ep>; */
- };
- };
- };
-};
-
/* PINCTRL - additions to nodes defined in sdm845.dtsi */
&qup_spi0_default {
config {
