Re: [PATCH v2 4/4] media: platform: Add Renesas RZ/G2L CRU driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Prabhakar,

On Mon, Sep 26, 2022 at 05:24:47PM +0100, Lad, Prabhakar wrote:
> On Mon, Sep 26, 2022 at 9:59 AM Laurent Pinchart wrote:
> > On Fri, Sep 23, 2022 at 08:02:12PM +0100, Lad, Prabhakar wrote:
> > > On Thu, Sep 22, 2022 at 4:29 PM Laurent Pinchart wrote:
> > > > On Tue, Sep 06, 2022 at 12:04:06AM +0100, Lad Prabhakar wrote:
> > > > > Add v4l driver for Renesas RZ/G2L Camera data Receiving Unit.
> > > > >
> > > > > Based on a patch in the BSP by Hien Huynh
> > > > > <hien.huynh.px@xxxxxxxxxxx>
> > > > >
> > > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> > > > > ---
> > > > > v1 -> v2
> > > > > * No change
> > > > >
> > > > > RFC v2 -> v1
> > > > > * Moved the driver to renesas folder
> > > > > * Fixed review comments pointed by Jacopo
> > > > >
> > > > > RFC v1 -> RFC v2
> > > > > * Dropped group
> > > > > * Dropped CSI subdev and implemented as new driver
> > > > > * Dropped "mc_" from function names
> > > > > * Moved the driver to renesas folder
> > > > > ---
> > > > >  .../media/platform/renesas/rzg2l-cru/Kconfig  |  17 +
> > > > >  .../media/platform/renesas/rzg2l-cru/Makefile |   3 +
> > > > >  .../platform/renesas/rzg2l-cru/rzg2l-core.c   | 395 ++++++++++
> > > > >  .../platform/renesas/rzg2l-cru/rzg2l-cru.h    | 152 ++++
> > > > >  .../platform/renesas/rzg2l-cru/rzg2l-dma.c    | 734 ++++++++++++++++++
> > > > >  .../platform/renesas/rzg2l-cru/rzg2l-v4l2.c   | 368 +++++++++
> > > >
> > > > I'd merge those two files together, they both handle the video node.
> > > > There's a comment below that recommends adding a subdev, that should
> > > > then go to a separate file.
> > >
> > > OK, I'll merge these files into rzg2l-video.c.
> > >
> > > > >  6 files changed, 1669 insertions(+)
> > > > >  create mode 100644 drivers/media/platform/renesas/rzg2l-cru/rzg2l-core.c
> > > > >  create mode 100644 drivers/media/platform/renesas/rzg2l-cru/rzg2l-cru.h
> > > > >  create mode 100644 drivers/media/platform/renesas/rzg2l-cru/rzg2l-dma.c
> > > > >  create mode 100644 drivers/media/platform/renesas/rzg2l-cru/rzg2l-v4l2.c
> > > > >
> > > > > diff --git a/drivers/media/platform/renesas/rzg2l-cru/Kconfig b/drivers/media/platform/renesas/rzg2l-cru/Kconfig
> > > > > index 57c40bb499df..08ff0e96b3f5 100644
> > > > > --- a/drivers/media/platform/renesas/rzg2l-cru/Kconfig
> > > > > +++ b/drivers/media/platform/renesas/rzg2l-cru/Kconfig
> > > > > @@ -15,3 +15,20 @@ config VIDEO_RZG2L_CSI2
> > > > >
> > > > >         To compile this driver as a module, choose M here: the
> > > > >         module will be called rzg2l-csi2.
> > > > > +
> > > > > +config VIDEO_RZG2L_CRU
> > > > > +     tristate "RZ/G2L Camera Receiving Unit (CRU) Driver"
> > > > > +     depends on ARCH_RENESAS || COMPILE_TEST
> > > > > +     depends on V4L_PLATFORM_DRIVERS
> > > > > +     depends on VIDEO_DEV && OF
> > > > > +     select MEDIA_CONTROLLER
> > > > > +     select V4L2_FWNODE
> > > > > +     select VIDEOBUF2_DMA_CONTIG
> > > > > +     select VIDEO_RZG2L_CSI2
> > > >
> > > > Is this required, can't the CRU be used with a parallel sensor without
> > > > the CSI-2 receiver ?
> > >
> > > Yes the CRU can be used with parallel sensors, I'll drop the above select.
> > >
> > > > > +     select VIDEO_V4L2_SUBDEV_API
> > > > > +     help
> > > > > +       Support for Renesas RZ/G2L (and alike SoC's) Camera Receiving
> > > > > +       Unit (CRU) driver.
> > > > > +
> > > > > +       To compile this driver as a module, choose M here: the
> > > > > +       module will be called rzg2l-cru.
> > > > > diff --git a/drivers/media/platform/renesas/rzg2l-cru/Makefile b/drivers/media/platform/renesas/rzg2l-cru/Makefile
> > > > > index 91ea97a944e6..7628809e953f 100644
> > > > > --- a/drivers/media/platform/renesas/rzg2l-cru/Makefile
> > > > > +++ b/drivers/media/platform/renesas/rzg2l-cru/Makefile
> > > > > @@ -1,3 +1,6 @@
> > > > >  # SPDX-License-Identifier: GPL-2.0
> > > > >
> > > > >  obj-$(CONFIG_VIDEO_RZG2L_CSI2) += rzg2l-csi2.o
> > > > > +
> > > > > +rzg2l-cru-objs = rzg2l-core.o rzg2l-dma.o rzg2l-v4l2.o
> > > > > +obj-$(CONFIG_VIDEO_RZG2L_CRU) += rzg2l-cru.o
> > > > > diff --git a/drivers/media/platform/renesas/rzg2l-cru/rzg2l-core.c b/drivers/media/platform/renesas/rzg2l-cru/rzg2l-core.c
> > > > > new file mode 100644
> > > > > index 000000000000..b5d4110b1913
> > > > > --- /dev/null
> > > > > +++ b/drivers/media/platform/renesas/rzg2l-cru/rzg2l-core.c
> > > > > @@ -0,0 +1,395 @@
> > > > > +// SPDX-License-Identifier: GPL-2.0+
> > > > > +/*
> > > > > + * Driver for Renesas RZ/G2L CRU
> > > > > + *
> > > > > + * Copyright (C) 2022 Renesas Electronics Corp.
> > > > > + *
> > > > > + * Based on Renesas R-Car VIN
> > > > > + * Copyright (C) 2011-2013 Renesas Solutions Corp.
> > > > > + * Copyright (C) 2013 Cogent Embedded, Inc., <source@xxxxxxxxxxxxxxxxxx>
> > > > > + * Copyright (C) 2008 Magnus Damm
> > > > > + */
> > > > > +
> > > > > +#include <linux/clk.h>
> > > > > +#include <linux/module.h>
> > > > > +#include <linux/mod_devicetable.h>
> > > > > +#include <linux/of.h>
> > > > > +#include <linux/of_device.h>
> > > > > +#include <linux/of_graph.h>
> > > > > +#include <linux/platform_device.h>
> > > > > +#include <linux/pm_runtime.h>
> > > > > +
> > > > > +#include <media/v4l2-fwnode.h>
> > > > > +#include <media/v4l2-mc.h>
> > > > > +
> > > > > +#include "rzg2l-cru.h"
> > > > > +
> > > > > +#define v4l2_dev_to_cru(d)   container_of(d, struct rzg2l_cru_dev, v4l2_dev)
> > > >
> > > > As this macro is only used to get the rzg2l_cru_dev pointer from the
> > > > v4l2_async_notifier pointer, you can replace it with
> > > >
> > > > #define notifier_to_cru(n)      container_of(n, struct rzg2l_cru_dev, notifier)
> > > >
> > > > I would also turn it into a static inline function for additional
> > > > compile-time type safety.
> > >
> > > OK, I will do it as mentioned above.
> > >
> > > > > +
> > > > > +static int rzg2l_cru_csi2_link_notify(struct media_link *link, u32 flags,
> > > > > +                                   unsigned int notification)
> > > > > +{
> > > > > +     struct media_entity *entity;
> > > > > +     struct rzg2l_cru_dev *cru;
> > > > > +     struct media_pad *csi_pad;
> > > > > +     struct v4l2_subdev *sd;
> > > > > +     int ret;
> > > > > +
> > > > > +     ret = v4l2_pipeline_link_notify(link, flags, notification);
> > > > > +     if (ret)
> > > > > +             return ret;
> > > > > +
> > > > > +     /* Only care about link enablement for CRU nodes. */
> > > > > +     if (!(flags & MEDIA_LNK_FL_ENABLED))
> > > > > +             return 0;
> > > > > +
> > > > > +     cru = container_of(link->graph_obj.mdev, struct rzg2l_cru_dev, mdev);
> > > > > +     /*
> > > > > +      * Don't allow link changes if any entity in the graph is
> > > > > +      * streaming, modifying the CHSEL register fields can disrupt
> > > > > +      * running streams.
> > > > > +      */
> > > > > +     media_device_for_each_entity(entity, &cru->mdev)
> > > > > +             if (media_entity_is_streaming(entity))
> > > > > +                     return -EBUSY;
> > > > > +
> > > > > +     mutex_lock(&cru->mdev_lock);
> > > > > +
> > > > > +     csi_pad = media_pad_remote_pad_first(&cru->vdev.entity.pads[0]);
> > > > > +     if (csi_pad) {
> > > > > +             ret = -EMLINK;
> > > > > +             goto out;
> > > > > +     }
> > > > > +
> > > > > +     sd = media_entity_to_v4l2_subdev(link->source->entity);
> > > > > +     if (cru->csi.subdev == sd) {
> > > > > +             cru->csi.channel = link->source->index - 1;
> > > > > +             cru->is_csi = true;
> > > > > +     } else {
> > > > > +             ret = -ENODEV;
> > > > > +     }
> > > > > +
> > > > > +out:
> > > > > +     mutex_unlock(&cru->mdev_lock);
> > > > > +
> > > > > +     return ret;
> > > > > +}
> > > > > +
> > > > > +static const struct media_device_ops rzg2l_cru_media_ops = {
> > > > > +     .link_notify = rzg2l_cru_csi2_link_notify,
> > > > > +};
> > > > > +
> > > > > +/* -----------------------------------------------------------------------------
> > > > > + * Group async notifier
> > > > > + */
> > > > > +
> > > > > +static int rzg2l_cru_group_notify_complete(struct v4l2_async_notifier *notifier)
> > > > > +{
> > > > > +     struct rzg2l_cru_dev *cru = v4l2_dev_to_cru(notifier->v4l2_dev);
> > > > > +     unsigned int i;
> > > > > +     int ret;
> > > > > +
> > > > > +     ret = media_device_register(&cru->mdev);
> > > > > +     if (ret)
> > > > > +             return ret;
> > > >
> > > > I'd move the v4l2_device_register() call here, as it's the V4L2
> > > > counterpart of the media device, and handling them together would be
> > > > best.
> > >
> > > OK.
> > >
> > > > > +
> > > > > +     ret = v4l2_device_register_subdev_nodes(&cru->v4l2_dev);
> > > > > +     if (ret) {
> > > > > +             dev_err(cru->dev, "Failed to register subdev nodes\n");
> > > > > +             return ret;
> > > > > +     }
> > > > > +
> > > > > +     if (!video_is_registered(&cru->vdev)) {
> > > >
> > > > Can this happen ?
> > >
> > > No, I'll drop this check.
> > >
> > > > > +             ret = rzg2l_cru_v4l2_register(cru);
> > > > > +             if (ret)
> > > > > +                     return ret;
> > > > > +     }
> > > > > +
> > > > > +     /* Create all media device links between CRU and CSI-2's. */
> > > > > +     /*
> > > > > +      * TODO: RZ/G2L supports 4 VC0, as support for virtual channels
> > > > > +      * should be implemented by streams API which is under development
> > > > > +      * so for now just link it to VC0
> > > > > +      */
> > > >
> > > > The streams API won't require more links, so I'd drop the comment and
> > > > the loop and create a single link.
> > >
> > > OK.
> > >
> > > > > +     for (i = 1; i <= 1; i++) {
> > > > > +             struct media_entity *source, *sink;
> > > > > +
> > > > > +             source = &cru->csi.subdev->entity;
> > > > > +             sink = &cru->vdev.entity;
> > > >
> > > > Hmmm... I'd recommend adding a subdev to model the image processing
> > > > pipeline of the CRU, between the CSI-2 receiver and the video node. That
> > > > will help when you'll add support for parallel sensors, and it will also
> > > > be needed by the streams API to select which virtual channel to capture.
> > >/
> > > just model as a dummy subdev for now (MEDIA_ENT_F_VID_MUX)?
> >
> > I think MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER would be more
> > appropriate.
> 
> OK I will use MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER. As this will be
> just like a switch should I be implementing the get_fmt/set_fmt
> callbacks?

Yes, subdev operations need to be implemented, especially given that the
CRU implements color space conversion, so the input and output formats
of the subdev can be different.

> > > > > +
> > > > > +             ret = media_create_pad_link(source, i, sink, 0, 0);
> > > > > +             if (ret) {
> > > > > +                     dev_err(cru->dev, "Error adding link from %s to %s\n",
> > > > > +                             source->name, sink->name);
> > > > > +                     break;
> > > > > +             }
> > > > > +     }
> > > > > +
> > > > > +     return ret;
> > > > > +}
> > > > > +
> > > > > +static void rzg2l_cru_group_notify_unbind(struct v4l2_async_notifier *notifier,
> > > > > +                                       struct v4l2_subdev *subdev,
> > > > > +                                       struct v4l2_async_subdev *asd)
> > > > > +{
> > > > > +     struct rzg2l_cru_dev *cru = v4l2_dev_to_cru(notifier->v4l2_dev);
> > > > > +
> > > > > +     rzg2l_cru_v4l2_unregister(cru);
> > > > > +
> > > > > +     mutex_lock(&cru->mdev_lock);
> > > > > +
> > > > > +     if (cru->csi.asd == asd) {
> > > > > +             cru->csi.subdev = NULL;
> > > > > +             dev_dbg(cru->dev, "Unbind CSI-2 %s\n", subdev->name);
> > > > > +     }
> > > > > +
> > > > > +     mutex_unlock(&cru->mdev_lock);
> > > > > +
> > > > > +     media_device_unregister(&cru->mdev);
> > > > > +}
> > > > > +
> > > > > +static int rzg2l_cru_group_notify_bound(struct v4l2_async_notifier *notifier,
> > > > > +                                     struct v4l2_subdev *subdev,
> > > > > +                                     struct v4l2_async_subdev *asd)
> > > > > +{
> > > > > +     struct rzg2l_cru_dev *cru = v4l2_dev_to_cru(notifier->v4l2_dev);
> > > > > +
> > > > > +     mutex_lock(&cru->mdev_lock);
> > > > > +
> > > > > +     if (cru->csi.asd == asd) {
> > > > > +             cru->csi.subdev = subdev;
> > > > > +             dev_dbg(cru->dev, "Bound CSI-2 %s\n", subdev->name);
> > > > > +     }
> > > > > +
> > > > > +     mutex_unlock(&cru->mdev_lock);
> > > > > +
> > > > > +     return 0;
> > > > > +}
> > > > > +
> > > > > +static const struct v4l2_async_notifier_operations rzg2l_cru_async_ops = {
> > > > > +     .bound = rzg2l_cru_group_notify_bound,
> > > > > +     .unbind = rzg2l_cru_group_notify_unbind,
> > > > > +     .complete = rzg2l_cru_group_notify_complete,
> > > > > +};
> > > > > +
> > > > > +static int rvin_mc_parse_of(struct rzg2l_cru_dev *cru, unsigned int id)
> > > >
> > > > The id parameter is always 0, I'd drop it.
> > >
> > > Agreed, I will drop it.
> > >
> > > > > +{
> > > > > +     struct v4l2_fwnode_endpoint vep = {
> > > > > +             .bus_type = V4L2_MBUS_CSI2_DPHY,
> > > > > +     };
> > > > > +     struct fwnode_handle *ep, *fwnode;
> > > > > +     struct v4l2_async_subdev *asd;
> > > > > +     int ret;
> > > > > +
> > > > > +     ep = fwnode_graph_get_endpoint_by_id(dev_fwnode(cru->dev), 1, id, 0);
> > > > > +     if (!ep)
> > > > > +             return 0;
> > > > > +
> > > > > +     fwnode = fwnode_graph_get_remote_endpoint(ep);
> > > > > +     ret = v4l2_fwnode_endpoint_parse(ep, &vep);
> > > > > +     fwnode_handle_put(ep);
> > > > > +     if (ret) {
> > > > > +             dev_err(cru->dev, "Failed to parse %pOF\n", to_of_node(fwnode));
> > > > > +             ret = -EINVAL;
> > > > > +             goto out;
> > > > > +     }
> > > > > +
> > > > > +     if (!of_device_is_available(to_of_node(fwnode))) {
> > > > > +             dev_dbg(cru->dev, "OF device %pOF disabled, ignoring\n",
> > > > > +                     to_of_node(fwnode));
> > > > > +             ret = -ENOTCONN;
> > > > > +             goto out;
> > > > > +     }
> > > > > +
> > > > > +     asd = v4l2_async_nf_add_fwnode(&cru->notifier, fwnode,
> > > > > +                                    struct v4l2_async_subdev);
> > > > > +     if (IS_ERR(asd)) {
> > > > > +             ret = PTR_ERR(asd);
> > > > > +             goto out;
> > > > > +     }
> > > > > +
> > > > > +     cru->csi.asd = asd;
> > > > > +
> > > > > +     dev_dbg(cru->dev, "Added OF device %pOF to slot %u\n",
> > > > > +             to_of_node(fwnode), vep.base.id);
> > > > > +out:
> > > > > +     fwnode_handle_put(fwnode);
> > > > > +
> > > > > +     return ret;
> > > > > +}
> > > > > +
> > > > > +static int rzg2l_cru_mc_parse_of_graph(struct rzg2l_cru_dev *cru)
> > > > > +{
> > > > > +     int ret;
> > > > > +
> > > > > +     v4l2_async_nf_init(&cru->notifier);
> > > > > +
> > > > > +     ret = rvin_mc_parse_of(cru, 0);
> > > > > +     if (ret)
> > > > > +             return ret;
> > > > > +
> > > > > +     cru->notifier.ops = &rzg2l_cru_async_ops;
> > > > > +
> > > > > +     if (list_empty(&cru->notifier.asd_list))
> > > > > +             return 0;
> > > > > +
> > > > > +     ret = v4l2_async_nf_register(&cru->v4l2_dev, &cru->notifier);
> > > > > +     if (ret < 0) {
> > > > > +             dev_err(cru->dev, "Notifier registration failed\n");
> > > > > +             v4l2_async_nf_cleanup(&cru->notifier);
> > > > > +             return ret;
> > > > > +     }
> > > > > +
> > > > > +     return 0;
> > > > > +}
> > > > > +
> > > > > +static int rzg2l_cru_csi2_init(struct rzg2l_cru_dev *cru)
> > > >
> > > > The naming is a bit weird, as this isn't related to CSI-2. I would name
> > > > the function rzg2l_cru_media_init().
> > >
> > > Agreed, I will rename it.
> > >
> > > > > +{
> > > > > +     struct media_device *mdev = NULL;
> > > > > +     const struct of_device_id *match;
> > > > > +     int ret;
> > > > > +
> > > > > +     cru->pad.flags = MEDIA_PAD_FL_SINK;
> > > > > +     ret = media_entity_pads_init(&cru->vdev.entity, 1, &cru->pad);
> > > > > +     if (ret)
> > > > > +             return ret;
> > > > > +
> > > > > +     mutex_init(&cru->mdev_lock);
> > > > > +     mdev = &cru->mdev;
> > > > > +     mdev->dev = cru->dev;
> > > > > +     mdev->ops = &rzg2l_cru_media_ops;
> > > > > +
> > > > > +     match = of_match_node(cru->dev->driver->of_match_table,
> > > > > +                           cru->dev->of_node);
> > > > > +
> > > > > +     strscpy(mdev->driver_name, KBUILD_MODNAME, sizeof(mdev->driver_name));
> > > > > +     strscpy(mdev->model, match->compatible, sizeof(mdev->model));
> > > > > +     snprintf(mdev->bus_info, sizeof(mdev->bus_info), "platform:%s",
> > > > > +              dev_name(mdev->dev));
> > > > > +
> > > > > +     cru->v4l2_dev.mdev = &cru->mdev;
> > > > > +
> > > > > +     media_device_init(mdev);
> > > > > +
> > > > > +     ret = rzg2l_cru_mc_parse_of_graph(cru);
> > > > > +     if (ret) {
> > > > > +             mutex_lock(&cru->mdev_lock);
> > > > > +             cru->v4l2_dev.mdev = NULL;
> > > > > +             mutex_unlock(&cru->mdev_lock);
> > > > > +     }
> > > > > +
> > > > > +     return 0;
> > > > > +}
> > > > > +
> > > > > +static int rzg2l_cru_probe(struct platform_device *pdev)
> > > > > +{
> > > > > +     struct rzg2l_cru_dev *cru;
> > > > > +     int irq, ret;
> > > > > +
> > > > > +     cru = devm_kzalloc(&pdev->dev, sizeof(*cru), GFP_KERNEL);
> > > > > +     if (!cru)
> > > > > +             return -ENOMEM;
> > > > > +
> > > > > +     cru->base = devm_platform_ioremap_resource(pdev, 0);
> > > > > +     if (IS_ERR(cru->base))
> > > > > +             return PTR_ERR(cru->base);
> > > > > +
> > > > > +     cru->presetn = devm_reset_control_get(&pdev->dev, "presetn");
> > > > > +     if (IS_ERR(cru->presetn))
> > > > > +             return dev_err_probe(&pdev->dev, PTR_ERR(cru->presetn),
> > > > > +                                  "failed to get cpg presetn\n");
> > > > > +
> > > > > +     cru->aresetn = devm_reset_control_get(&pdev->dev, "aresetn");
> > > > > +     if (IS_ERR(cru->aresetn))
> > > > > +             return dev_err_probe(&pdev->dev, PTR_ERR(cru->aresetn),
> > > > > +                                  "failed to get cpg aresetn\n");
> > > > > +
> > > > > +     cru->vclk = devm_clk_get(&pdev->dev, "vclk");
> > > > > +     if (IS_ERR(cru->vclk)) {
> > > > > +             dev_err(&pdev->dev, "Failed to get vclk");
> > > > > +             return PTR_ERR(cru->vclk);
> > > >
> > > > You could use dev_err_probe() here too (as well as below).
> > >
> > > OK.
> > >
> > > > > +     }
> > > > > +
> > > > > +     cru->pclk = devm_clk_get(&pdev->dev, "pclk");
> > > > > +     if (IS_ERR(cru->pclk)) {
> > > > > +             dev_err(&pdev->dev, "Failed to get pclk");
> > > > > +             return PTR_ERR(cru->pclk);
> > > > > +     }
> > > > > +
> > > > > +     cru->aclk = devm_clk_get(&pdev->dev, "aclk");
> > > > > +     if (IS_ERR(cru->aclk)) {
> > > > > +             dev_err(&pdev->dev, "Failed to get aclk");
> > > > > +             return PTR_ERR(cru->aclk);
> > > > > +     }
> > > > > +
> > > > > +     cru->dev = &pdev->dev;
> > > > > +     cru->info = of_device_get_match_data(&pdev->dev);
> > > > > +
> > > > > +     irq = platform_get_irq(pdev, 0);
> > > > > +     if (irq < 0)
> > > > > +             return irq;
> > > > > +
> > > > > +     ret = rzg2l_cru_dma_register(cru, irq);
> > > > > +     if (ret)
> > > > > +             return ret;
> > > > > +
> > > > > +     platform_set_drvdata(pdev, cru);
> > > > > +
> > > > > +     ret = rzg2l_cru_csi2_init(cru);
> > > > > +     if (ret)
> > > > > +             goto error_dma_unregister;
> > > > > +
> > > > > +     cru->num_buf = HW_BUFFER_DEFAULT;
> > > > > +     pm_suspend_ignore_children(&pdev->dev, true);
> > > > > +     pm_runtime_enable(&pdev->dev);
> > > > > +
> > > > > +     return 0;
> > > > > +
> > > > > +error_dma_unregister:
> > > > > +     rzg2l_cru_dma_unregister(cru);
> > > > > +
> > > > > +     return ret;
> > > > > +}
> > > > > +
> > > > > +static const struct of_device_id rzg2l_cru_of_id_table[] = {
> > > > > +     {
> > > > > +             .compatible = "renesas,rzg2l-cru",
> > > > > +     },
> > > > > +     { /* sentinel */ }
> > > > > +};
> > > > > +MODULE_DEVICE_TABLE(of, rzg2l_cru_of_id_table);
> > > > > +
> > > > > +static int rzg2l_cru_remove(struct platform_device *pdev)
> > > > > +{
> > > > > +     struct rzg2l_cru_dev *cru = platform_get_drvdata(pdev);
> > > > > +
> > > > > +     pm_runtime_disable(&pdev->dev);
> > > > > +
> > > > > +     rzg2l_cru_v4l2_unregister(cru);
> > > > > +
> > > > > +     v4l2_async_nf_unregister(&cru->notifier);
> > > > > +     v4l2_async_nf_cleanup(&cru->notifier);
> > > > > +
> > > > > +     media_device_cleanup(&cru->mdev);
> > > > > +     mutex_destroy(&cru->mdev_lock);
> > > > > +     cru->v4l2_dev.mdev = NULL;
> > > >
> > > > Is this needed ?
> > >
> > > Not required.
> > >
> > > > > +
> > > > > +     rzg2l_cru_dma_unregister(cru);
> > > > > +
> > > > > +     return 0;
> > > > > +}
> > > > > +
> > > > > +static struct platform_driver rzg2l_cru_driver = {
> > > > > +     .driver = {
> > > > > +             .name = "rzg2l-cru",
> > > > > +             .of_match_table = rzg2l_cru_of_id_table,
> > > > > +     },
> > > > > +     .probe = rzg2l_cru_probe,
> > > > > +     .remove = rzg2l_cru_remove,
> > > >
> > > > No PM ?
> > >
> > > I plan to gradually add at a later point.
> > >
> > > > > +};
> > > > > +
> > > > > +module_platform_driver(rzg2l_cru_driver);
> > > > > +
> > > > > +MODULE_AUTHOR("Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>");
> > > > > +MODULE_DESCRIPTION("Renesas RZ/G2L CRU driver");
> > > > > +MODULE_LICENSE("GPL");
> > > > > diff --git a/drivers/media/platform/renesas/rzg2l-cru/rzg2l-cru.h b/drivers/media/platform/renesas/rzg2l-cru/rzg2l-cru.h
> > > > > new file mode 100644
> > > > > index 000000000000..a834680a3200
> > > > > --- /dev/null
> > > > > +++ b/drivers/media/platform/renesas/rzg2l-cru/rzg2l-cru.h
> > > > > @@ -0,0 +1,152 @@
> > > > > +/* SPDX-License-Identifier: GPL-2.0+ */
> > > > > +/*
> > > > > + * Driver for Renesas RZ/G2L CRU
> > > > > + *
> > > > > + * Copyright (C) 2022 Renesas Electronics Corp.
> > > > > + *
> > > >
> > > > Extra blank line.
> > >
> > > Oops, I will drop it.
> > >
> > > > > + */
> > > > > +
> > > > > +#ifndef __RZG2L_CRU__
> > > > > +#define __RZG2L_CRU__
> > > > > +
> > > > > +#include <linux/reset.h>
> > > > > +
> > > > > +#include <media/v4l2-async.h>
> > > > > +#include <media/v4l2-ctrls.h>
> > > > > +#include <media/v4l2-dev.h>
> > > > > +#include <media/v4l2-device.h>
> > > > > +#include <media/videobuf2-v4l2.h>
> > > > > +
> > > > > +/* Number of HW buffers */
> > > > > +#define HW_BUFFER_MAX                8
> > > > > +#define HW_BUFFER_DEFAULT    3
> > > >
> > > > Could you prefix macro names with CRU_ (or RZG2L_CRU_, up to you) ?
> > > > These names are a bit generic and could lead to clashes.
> > >
> > > Agreed, I will rename it.
> > >
> > > > > +
> > > > > +/* Address alignment mask for HW buffers */
> > > > > +#define HW_BUFFER_MASK               0x1ff
> > > > > +
> > > > > +/* Maximum number of CSI2 virtual channels */
> > > > > +#define CSI2_VCHANNEL                4
> > > > > +
> > > > > +#define CRU_MAX_INPUT_WIDTH  2800
> > > > > +#define CRU_MAX_INPUT_HEIGHT 4095
> > > > > +
> > > > > +/**
> > > > > + * enum rzg2l_cru_dma_state - DMA states
> > > > > + * @RZG2L_CRU_DMA_STOPPED:   No operation in progress
> > > > > + * @RZG2L_CRU_DMA_STARTING:  Capture starting up
> > > > > + * @RZG2L_CRU_DMA_RUNNING:   Operation in progress have buffers
> > > > > + * @RZG2L_CRU_DMA_STOPPING:  Stopping operation
> > > > > + */
> > > > > +enum rzg2l_cru_dma_state {
> > > > > +     RZG2L_CRU_DMA_STOPPED = 0,
> > > > > +     RZG2L_CRU_DMA_STARTING,
> > > > > +     RZG2L_CRU_DMA_RUNNING,
> > > > > +     RZG2L_CRU_DMA_STOPPING,
> > > > > +};
> > > > > +
> > > > > +struct rzg2l_cru_csi {
> > > > > +     struct v4l2_async_subdev *asd;
> > > > > +     struct v4l2_subdev *subdev;
> > > > > +     u32 channel;
> > > > > +};
> > > > > +
> > > > > +/**
> > > > > + * struct rzg2l_cru_dev - Renesas CRU device structure
> > > > > + * @dev:             (OF) device
> > > > > + * @base:            device I/O register space remapped to virtual memory
> > > > > + * @info:            info about CRU instance
> > > > > + *
> > > > > + * @presetn:         CRU_PRESETN reset line
> > > > > + * @aresetn:         CRU_ARESETN reset line
> > > > > + *
> > > > > + * @vclk:            CRU Main clock
> > > > > + * @pclk:            CPU Register access clock
> > > > > + * @aclk:            CRU image transfer clock
> > > > > + *
> > > > > + * @vdev:            V4L2 video device associated with CRU
> > > > > + * @v4l2_dev:                V4L2 device
> > > > > + * @ctrl_handler:    V4L2 control handler
> > > > > + * @num_buf:         Holds the current number of buffers enabled
> > > > > + * @notifier:                V4L2 asynchronous subdevs notifier
> > > > > + *
> > > > > + * @csi:             CSI info
> > > > > + * @mdev:            media device
> > > > > + * @mdev_lock:               protects the count, notifier and csi members
> > > > > + * @pad:             media pad for the video device entity
> > > > > + *
> > > > > + * @lock:            protects @queue
> > > > > + * @queue:           vb2 buffers queue
> > > > > + * @scratch:         cpu address for scratch buffer
> > > > > + * @scratch_phys:    physical address of the scratch buffer
> > > > > + *
> > > > > + * @qlock:           protects @queue_buf, @buf_list, @sequence
> > > > > + *                   @state
> > > > > + * @queue_buf:               Keeps track of buffers given to HW slot
> > > > > + * @buf_list:                list of queued buffers
> > > > > + * @sequence:                V4L2 buffers sequence number
> > > > > + * @state:           keeps track of operation state
> > > > > + *
> > > > > + * @is_csi:          flag to mark the CRU as using a CSI-2 subdevice
> > > > > + *
> > > > > + * @input_is_yuv:    flag to mark the input format of CRU
> > > > > + * @output_is_yuv:   flag to mark the output format of CRU
> > > > > + *
> > > > > + * @mbus_code:               media bus format code
> > > > > + * @format:          active V4L2 pixel format
> > > > > + *
> > > > > + * @compose:         active composing
> > > > > + */
> > > > > +struct rzg2l_cru_dev {
> > > > > +     struct device *dev;
> > > > > +     void __iomem *base;
> > > > > +     const struct rzg2l_cru_info *info;
> > > > > +
> > > > > +     struct reset_control *presetn;
> > > > > +     struct reset_control *aresetn;
> > > > > +
> > > > > +     struct clk *vclk;
> > > > > +     struct clk *pclk;
> > > > > +     struct clk *aclk;
> > > > > +
> > > > > +     struct video_device vdev;
> > > > > +     struct v4l2_device v4l2_dev;
> > > > > +     u8 num_buf;
> > > > > +
> > > > > +     struct v4l2_async_notifier notifier;
> > > > > +
> > > > > +     struct rzg2l_cru_csi csi;
> > > > > +     struct media_device mdev;
> > > > > +     struct mutex mdev_lock;
> > > > > +     struct media_pad pad;
> > > > > +
> > > > > +     struct mutex lock;
> > > > > +     struct vb2_queue queue;
> > > > > +     void *scratch;
> > > > > +     dma_addr_t scratch_phys;
> > > > > +
> > > > > +     spinlock_t qlock;
> > > > > +     struct vb2_v4l2_buffer *queue_buf[HW_BUFFER_MAX];
> > > > > +     struct list_head buf_list;
> > > > > +     unsigned int sequence;
> > > > > +     enum rzg2l_cru_dma_state state;
> > > > > +
> > > > > +     bool is_csi;
> > > > > +
> > > > > +     bool input_is_yuv;
> > > > > +     bool output_is_yuv;
> > > > > +
> > > > > +     u32 mbus_code;
> > > > > +     struct v4l2_pix_format format;
> > > > > +
> > > > > +     struct v4l2_rect compose;
> > > > > +};
> > > > > +
> > > > > +int rzg2l_cru_dma_register(struct rzg2l_cru_dev *cru, int irq);
> > > > > +void rzg2l_cru_dma_unregister(struct rzg2l_cru_dev *cru);
> > > > > +
> > > > > +int rzg2l_cru_v4l2_register(struct rzg2l_cru_dev *cru);
> > > > > +void rzg2l_cru_v4l2_unregister(struct rzg2l_cru_dev *cru);
> > > > > +
> > > > > +const struct v4l2_format_info *rzg2l_cru_format_from_pixel(u32 format);
> > > > > +
> > > > > +#endif
> > > > > diff --git a/drivers/media/platform/renesas/rzg2l-cru/rzg2l-dma.c b/drivers/media/platform/renesas/rzg2l-cru/rzg2l-dma.c
> > > > > new file mode 100644
> > > > > index 000000000000..44efd071f562
> > > > > --- /dev/null
> > > > > +++ b/drivers/media/platform/renesas/rzg2l-cru/rzg2l-dma.c
> > > > > @@ -0,0 +1,734 @@
> > > > > +// SPDX-License-Identifier: GPL-2.0+
> > > > > +/*
> > > > > + * Driver for Renesas RZ/G2L CRU
> > > > > + *
> > > > > + * Copyright (C) 2022 Renesas Electronics Corp.
> > > > > + *
> > > > > + * Based on Renesas R-Car VIN
> > > > > + * Copyright (C) 2011-2013 Renesas Solutions Corp.
> > > > > + * Copyright (C) 2013 Cogent Embedded, Inc., <source@xxxxxxxxxxxxxxxxxx>
> > > > > + * Copyright (C) 2008 Magnus Damm
> > > > > + */
> > > > > +
> > > > > +#include <linux/clk.h>
> > > > > +#include <linux/delay.h>
> > > > > +#include <linux/interrupt.h>
> > > > > +
> > > > > +#include <media/videobuf2-dma-contig.h>
> > > > > +
> > > > > +#include "rzg2l-cru.h"
> > > > > +#include "rzg2l-csi2.h"
> > > > > +
> > > > > +/* HW CRU Registers Definition */
> > > > > +/* CRU Control Register */
> > > > > +#define CRUnCTRL                     0x0
> > > > > +#define CRUnCTRL_VINSEL(x)           ((x) << 0)
> > > > > +
> > > > > +/* CRU Interrupt Enable Register */
> > > > > +#define CRUnIE                               0x4
> > > > > +#define CRUnIE_SFE                   BIT(16)
> > > > > +#define CRUnIE_EFE                   BIT(17)
> > > > > +
> > > > > +/* CRU Interrupt Status Register */
> > > > > +#define CRUnINTS                     0x8
> > > > > +#define CRUnINTS_SFS                 BIT(16)
> > > > > +
> > > > > +/* CRU Reset Register */
> > > > > +#define CRUnRST                              0xc
> > > > > +#define CRUnRST_VRESETN                      BIT(0)
> > > > > +
> > > > > +/* Memory Bank Base Address (Lower) Register for CRU Image Data */
> > > > > +#define AMnMBxADDRL(x)                       (0x100 + ((x) * 8))
> > > > > +
> > > > > +/* Memory Bank Base Address (Higher) Register for CRU Image Data */
> > > > > +#define AMnMBxADDRH(x)                       (0x104 + ((x) * 8))
> > > > > +
> > > > > +/* Memory Bank Enable Register for CRU Image Data */
> > > > > +#define AMnMBVALID                   0x148
> > > > > +#define AMnMBVALID_MBVALID(x)                GENMASK(x, 0)
> > > > > +
> > > > > +/* Memory Bank Status Register for CRU Image Data */
> > > > > +#define AMnMBS                               0x14c
> > > > > +#define AMnMBS_MBSTS                 0x7
> > > > > +
> > > > > +/* AXI Master FIFO Pointer Register for CRU Image Data */
> > > > > +#define AMnFIFOPNTR                  0x168
> > > > > +#define AMnFIFOPNTR_FIFOWPNTR                GENMASK(7, 0)
> > > > > +#define AMnFIFOPNTR_FIFORPNTR_Y              GENMASK(23, 16)
> > > > > +
> > > > > +/* AXI Master Transfer Stop Register for CRU Image Data */
> > > > > +#define AMnAXISTP                    0x174
> > > > > +#define AMnAXISTP_AXI_STOP           BIT(0)
> > > > > +
> > > > > +/* AXI Master Transfer Stop Status Register for CRU Image Data */
> > > > > +#define AMnAXISTPACK                 0x178
> > > > > +#define AMnAXISTPACK_AXI_STOP_ACK    BIT(0)
> > > > > +
> > > > > +/* CRU Image Processing Enable Register */
> > > > > +#define ICnEN                                0x200
> > > > > +#define ICnEN_ICEN                   BIT(0)
> > > > > +
> > > > > +/* CRU Image Processing Main Control Register */
> > > > > +#define ICnMC                                0x208
> > > > > +#define ICnMC_CSCTHR                 BIT(5)
> > > > > +#define ICnMC_INF_YUV8_422           (0x1e << 16)
> > > > > +#define ICnMC_INF_USER                       (0x30 << 16)
> > > > > +#define ICnMC_VCSEL(x)                       ((x) << 22)
> > > > > +#define ICnMC_INF_MASK                       GENMASK(21, 16)
> > > > > +
> > > > > +/* CRU Module Status Register */
> > > > > +#define ICnMS                                0x254
> > > > > +#define ICnMS_IA                     BIT(2)
> > > > > +
> > > > > +/* CRU Data Output Mode Register */
> > > > > +#define ICnDMR                               0x26c
> > > > > +#define ICnDMR_YCMODE_UYVY           (1 << 4)
> > > > > +
> > > > > +#define RZG2L_TIMEOUT_MS             100
> > > > > +#define RZG2L_RETRIES                        10
> > > > > +
> > > > > +struct rzg2l_cru_buffer {
> > > > > +     struct vb2_v4l2_buffer vb;
> > > > > +     struct list_head list;
> > > > > +};
> > > > > +
> > > > > +#define to_buf_list(vb2_buffer) (&container_of(vb2_buffer, \
> > > > > +                                             struct rzg2l_cru_buffer, \
> > > > > +                                             vb)->list)
> > > > > +
> > > > > +static void rzg2l_cru_write(struct rzg2l_cru_dev *cru, u32 offset, u32 value)
> > > > > +{
> > > > > +     iowrite32(value, cru->base + offset);
> > > > > +}
> > > > > +
> > > > > +static u32 rzg2l_cru_read(struct rzg2l_cru_dev *cru, u32 offset)
> > > > > +{
> > > > > +     return ioread32(cru->base + offset);
> > > > > +}
> > > > > +
> > > > > +/* Need to hold qlock before calling */
> > > > > +static void return_unused_buffers(struct rzg2l_cru_dev *cru,
> > > > > +                               enum vb2_buffer_state state)
> > > > > +{
> > > > > +     struct rzg2l_cru_buffer *buf, *node;
> > > > > +     unsigned long flags;
> > > > > +     unsigned int i;
> > > > > +
> > > > > +     spin_lock_irqsave(&cru->qlock, flags);
> > > > > +     for (i = 0; i < cru->num_buf; i++) {
> > > > > +             if (cru->queue_buf[i]) {
> > > > > +                     vb2_buffer_done(&cru->queue_buf[i]->vb2_buf,
> > > > > +                                     state);
> > > > > +                     cru->queue_buf[i] = NULL;
> > > > > +             }
> > > > > +     }
> > > > > +
> > > > > +     list_for_each_entry_safe(buf, node, &cru->buf_list, list) {
> > > > > +             vb2_buffer_done(&buf->vb.vb2_buf, state);
> > > > > +             list_del(&buf->list);
> > > > > +     }
> > > > > +     spin_unlock_irqrestore(&cru->qlock, flags);
> > > > > +}
> > > > > +
> > > > > +static int rzg2l_cru_queue_setup(struct vb2_queue *vq, unsigned int *nbuffers,
> > > > > +                              unsigned int *nplanes, unsigned int sizes[],
> > > > > +                              struct device *alloc_devs[])
> > > > > +{
> > > > > +     struct rzg2l_cru_dev *cru = vb2_get_drv_priv(vq);
> > > > > +
> > > > > +     /* Make sure the image size is large enough. */
> > > > > +     if (*nplanes)
> > > > > +             return sizes[0] < cru->format.sizeimage ? -EINVAL : 0;
> > > > > +
> > > > > +     *nplanes = 1;
> > > > > +     sizes[0] = cru->format.sizeimage;
> > > > > +
> > > > > +     return 0;
> > > > > +};
> > > > > +
> > > > > +static int rzg2l_cru_buffer_prepare(struct vb2_buffer *vb)
> > > > > +{
> > > > > +     struct rzg2l_cru_dev *cru = vb2_get_drv_priv(vb->vb2_queue);
> > > > > +     unsigned long size = cru->format.sizeimage;
> > > > > +
> > > > > +     if (vb2_plane_size(vb, 0) < size) {
> > > > > +             dev_err(cru->dev, "buffer too small (%lu < %lu)\n",
> > > > > +                     vb2_plane_size(vb, 0), size);
> > > > > +             return -EINVAL;
> > > > > +     }
> > > > > +
> > > > > +     vb2_set_plane_payload(vb, 0, size);
> > > > > +
> > > > > +     return 0;
> > > > > +}
> > > > > +
> > > > > +static void rzg2l_cru_buffer_queue(struct vb2_buffer *vb)
> > > > > +{
> > > > > +     struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
> > > > > +     struct rzg2l_cru_dev *cru = vb2_get_drv_priv(vb->vb2_queue);
> > > > > +     unsigned long flags;
> > > > > +
> > > > > +     spin_lock_irqsave(&cru->qlock, flags);
> > > > > +
> > > > > +     list_add_tail(to_buf_list(vbuf), &cru->buf_list);
> > > > > +
> > > > > +     spin_unlock_irqrestore(&cru->qlock, flags);
> > > > > +}
> > > > > +
> > > > > +static int rzg2l_cru_mc_validate_format(struct rzg2l_cru_dev *cru,
> > > > > +                                     struct v4l2_subdev *sd,
> > > > > +                                     struct media_pad *pad)
> > > > > +{
> > > > > +     struct v4l2_subdev_format fmt = {
> > > > > +             .which = V4L2_SUBDEV_FORMAT_ACTIVE,
> > > > > +     };
> > > > > +
> > > > > +     fmt.pad = pad->index;
> > > > > +     if (v4l2_subdev_call_state_active(sd, pad, get_fmt, &fmt))
> > > > > +             return -EPIPE;
> > > > > +
> > > > > +     if (cru->is_csi) {
> > > > > +             switch (fmt.format.code) {
> > > > > +             case MEDIA_BUS_FMT_UYVY8_1X16:
> > > > > +                     break;
> > > > > +             default:
> > > > > +                     return -EPIPE;
> > > > > +             }
> > > > > +     }
> > > > > +     cru->mbus_code = fmt.format.code;
> > > > > +
> > > > > +     switch (fmt.format.field) {
> > > > > +     case V4L2_FIELD_TOP:
> > > > > +     case V4L2_FIELD_BOTTOM:
> > > > > +     case V4L2_FIELD_NONE:
> > > > > +     case V4L2_FIELD_INTERLACED_TB:
> > > > > +     case V4L2_FIELD_INTERLACED_BT:
> > > > > +     case V4L2_FIELD_INTERLACED:
> > > > > +     case V4L2_FIELD_SEQ_TB:
> > > > > +     case V4L2_FIELD_SEQ_BT:
> > > > > +             break;
> > > > > +     default:
> > > > > +             return -EPIPE;
> > > > > +     }
> > > > > +
> > > > > +     if (fmt.format.width != cru->format.width ||
> > > > > +         fmt.format.height != cru->format.height ||
> > > > > +         fmt.format.code != cru->mbus_code)
> > > > > +             return -EPIPE;
> > > > > +
> > > > > +     return 0;
> > > > > +}
> > > > > +
> > > > > +static void rzg2l_cru_set_slot_addr(struct rzg2l_cru_dev *cru,
> > > > > +                                 int slot, dma_addr_t addr)
> > > > > +{
> > > > > +     const struct v4l2_format_info *fmt;
> > > > > +     int offsetx, offsety;
> > > > > +     dma_addr_t offset;
> > > > > +
> > > > > +     fmt = rzg2l_cru_format_from_pixel(cru->format.pixelformat);
> > > > > +
> > > > > +     /*
> > > > > +      * There is no HW support for composition do the best we can
> > > > > +      * by modifying the buffer offset
> > > > > +      */
> > > > > +     offsetx = cru->compose.left * fmt->bpp[0];
> > > > > +     offsety = cru->compose.top * cru->format.bytesperline;
> > > > > +     offset = addr + offsetx + offsety;
> > > > > +
> > > > > +     /*
> > > > > +      * The address needs to be 512 bytes aligned. Driver should never accept
> > > > > +      * settings that do not satisfy this in the first place...
> > > > > +      */
> > > > > +     if (WARN_ON((offsetx | offsety | offset) & HW_BUFFER_MASK))
> > > > > +             return;
> > > > > +
> > > > > +     /* Currently, we just use the buffer in 32 bits address */
> > > > > +     rzg2l_cru_write(cru, AMnMBxADDRL(slot), offset);
> > > > > +     rzg2l_cru_write(cru, AMnMBxADDRH(slot), 0);
> > > > > +}
> > > > > +
> > > > > +/*
> > > > > + * Moves a buffer from the queue to the HW slot. If no buffer is
> > > > > + * available use the scratch buffer. The scratch buffer is never
> > > > > + * returned to userspace, its only function is to enable the capture
> > > > > + * loop to keep running.
> > > > > + */
> > > > > +static void rzg2l_cru_fill_hw_slot(struct rzg2l_cru_dev *cru, int slot)
> > > > > +{
> > > > > +     struct vb2_v4l2_buffer *vbuf;
> > > > > +     struct rzg2l_cru_buffer *buf;
> > > > > +     dma_addr_t phys_addr;
> > > > > +
> > > > > +     /* A already populated slot shall never be overwritten. */
> > > > > +     if (WARN_ON(cru->queue_buf[slot]))
> > > > > +             return;
> > > > > +
> > > > > +     dev_dbg(cru->dev, "Filling HW slot: %d\n", slot);
> > > > > +
> > > > > +     if (list_empty(&cru->buf_list)) {
> > > > > +             cru->queue_buf[slot] = NULL;
> > > > > +             phys_addr = cru->scratch_phys;
> > > > > +     } else {
> > > > > +             /* Keep track of buffer we give to HW */
> > > > > +             buf = list_entry(cru->buf_list.next,
> > > > > +                              struct rzg2l_cru_buffer, list);
> > > > > +             vbuf = &buf->vb;
> > > > > +             list_del_init(to_buf_list(vbuf));
> > > > > +             cru->queue_buf[slot] = vbuf;
> > > > > +
> > > > > +             /* Setup DMA */
> > > > > +             phys_addr = vb2_dma_contig_plane_dma_addr(&vbuf->vb2_buf, 0);
> > > > > +     }
> > > > > +
> > > > > +     rzg2l_cru_set_slot_addr(cru, slot, phys_addr);
> > > > > +}
> > > > > +
> > > > > +static void rzg2l_cru_initialize_axi(struct rzg2l_cru_dev *cru)
> > > > > +{
> > > > > +     unsigned int slot;
> > > > > +
> > > > > +     /*
> > > > > +      * Set image data memory banks.
> > > > > +      * Currently, we will use maximum address.
> > > > > +      */
> > > > > +     rzg2l_cru_write(cru, AMnMBVALID, AMnMBVALID_MBVALID(cru->num_buf - 1));
> > > > > +
> > > > > +     for (slot = 0; slot < cru->num_buf; slot++)
> > > > > +             rzg2l_cru_fill_hw_slot(cru, slot);
> > > > > +}
> > > > > +
> > > > > +static void rzg2l_cru_csi2_setup(struct rzg2l_cru_dev *cru)
> > > > > +{
> > > > > +     u32 icnmc;
> > > > > +
> > > > > +     switch (cru->mbus_code) {
> > > > > +     case MEDIA_BUS_FMT_UYVY8_1X16:
> > > > > +             icnmc = ICnMC_INF_YUV8_422;
> > > > > +             cru->input_is_yuv = true;
> > > > > +             break;
> > > > > +     default:
> > > > > +             cru->input_is_yuv = false;
> > > > > +             icnmc = ICnMC_INF_USER;
> > > > > +             break;
> > > > > +     }
> > > > > +
> > > > > +     icnmc |= (rzg2l_cru_read(cru, ICnMC) & ~ICnMC_INF_MASK);
> > > > > +
> > > > > +     /* Set virtual channel CSI2 */
> > > > > +     icnmc |= ICnMC_VCSEL(cru->csi.channel);
> > > > > +
> > > > > +     rzg2l_cru_write(cru, ICnMC, icnmc);
> > > > > +}
> > > > > +
> > > > > +static int rzg2l_cru_initialize_image_conv(struct rzg2l_cru_dev *cru)
> > > > > +{
> > > > > +     u32 icndmr;
> > > > > +
> > > > > +     if (cru->is_csi)
> > > > > +             rzg2l_cru_csi2_setup(cru);
> > > > > +
> > > > > +     /* Output format */
> > > > > +     switch (cru->format.pixelformat) {
> > > > > +     case V4L2_PIX_FMT_UYVY:
> > > > > +             icndmr = ICnDMR_YCMODE_UYVY;
> > > > > +             cru->output_is_yuv = true;
> > > > > +             break;
> > > > > +     default:
> > > > > +             dev_err(cru->dev, "Invalid pixelformat (0x%x)\n",
> > > > > +                     cru->format.pixelformat);
> > > > > +             return -EINVAL;
> > > > > +     }
> > > > > +
> > > > > +     /* If input and output use same colorspace, do bypass mode */
> > > > > +     if (cru->output_is_yuv == cru->input_is_yuv)
> > > > > +             rzg2l_cru_write(cru, ICnMC,
> > > > > +                             rzg2l_cru_read(cru, ICnMC) | ICnMC_CSCTHR);
> > > > > +     else
> > > > > +             rzg2l_cru_write(cru, ICnMC,
> > > > > +                             rzg2l_cru_read(cru, ICnMC) & (~ICnMC_CSCTHR));
> > > > > +
> > > > > +     /* Set output data format */
> > > > > +     rzg2l_cru_write(cru, ICnDMR, icndmr);
> > > > > +
> > > > > +     return 0;
> > > > > +}
> > > > > +
> > > > > +static int rzg2l_cru_set_stream(struct rzg2l_cru_dev *cru, int on)
> > > > > +{
> > > > > +     struct rzg2l_csi2 *csi2 = sd_to_csi2(cru->csi.subdev);
> > > > > +     struct media_pipeline *pipe;
> > > > > +     struct v4l2_subdev *sd;
> > > > > +     struct media_pad *pad;
> > > > > +     unsigned long flags;
> > > > > +     int ret;
> > > > > +
> > > > > +     pad = media_pad_remote_pad_first(&cru->pad);
> > > > > +     if (!pad)
> > > > > +             return -EPIPE;
> > > > > +
> > > > > +     sd = media_entity_to_v4l2_subdev(pad->entity);
> > > > > +
> > > > > +     if (!on) {
> > > > > +             media_pipeline_stop(&cru->vdev.entity);
> > > > > +             return v4l2_subdev_call(sd, video, s_stream, 0);
> > > > > +     }
> > > > > +
> > > > > +     ret = rzg2l_cru_mc_validate_format(cru, sd, pad);
> > > > > +     if (ret)
> > > > > +             return ret;
> > > > > +
> > > > > +     rzg2l_csi2_dphy_setting(csi2, 1);
> > > > > +
> > > > > +     spin_lock_irqsave(&cru->qlock, flags);
> > > > > +
> > > > > +     /* Select a video input */
> > > > > +     if (cru->is_csi)
> > > > > +             rzg2l_cru_write(cru, CRUnCTRL, CRUnCTRL_VINSEL(0));
> > > > > +
> > > > > +     /* Cancel the software reset for image processing block */
> > > > > +     rzg2l_cru_write(cru, CRUnRST, CRUnRST_VRESETN);
> > > > > +
> > > > > +     /* Disable and clear the interrupt before using */
> > > > > +     rzg2l_cru_write(cru, CRUnIE, 0);
> > > > > +     rzg2l_cru_write(cru, CRUnINTS, 0x001f000f);
> > > > > +
> > > > > +     /* Initialize the AXI master */
> > > > > +     rzg2l_cru_initialize_axi(cru);
> > > > > +
> > > > > +     /* Initialize image convert */
> > > > > +     ret = rzg2l_cru_initialize_image_conv(cru);
> > > > > +     if (ret) {
> > > > > +             spin_unlock_irqrestore(&cru->qlock, flags);
> > > > > +             return ret;
> > > > > +     }
> > > > > +
> > > > > +     /* Enable interrupt */
> > > > > +     rzg2l_cru_write(cru, CRUnIE, CRUnIE_EFE);
> > > > > +
> > > > > +     /* Enable image processing reception */
> > > > > +     rzg2l_cru_write(cru, ICnEN, ICnEN_ICEN);
> > > > > +
> > > > > +     spin_unlock_irqrestore(&cru->qlock, flags);
> > > > > +
> > > > > +     pipe = sd->entity.pipe ? sd->entity.pipe : &cru->vdev.pipe;
> > > > > +     ret = media_pipeline_start(&cru->vdev.entity, pipe);
> > > > > +     if (ret)
> > > > > +             return ret;
> > > > > +
> > > > > +     clk_disable_unprepare(cru->vclk);
> > > > > +
> > > > > +     rzg2l_csi2_mipi_link_setting(csi2, 1);
> > > > > +
> > > > > +     ret = clk_prepare_enable(cru->vclk);
> > > > > +     if (ret)
> > > > > +             return ret;
> > > > > +
> > > > > +     rzg2l_csi2_cmn_rstb_deassert(csi2);
> > > > > +
> > > > > +     ret = v4l2_subdev_call(sd, video, s_stream, 1);
> > > > > +     if (ret == -ENOIOCTLCMD)
> > > > > +             ret = 0;
> > > > > +     if (ret)
> > > > > +             media_pipeline_stop(&cru->vdev.entity);
> > > > > +
> > > > > +     return ret;
> > > > > +}
> > > > > +
> > > > > +static void rzg2l_cru_stop_streaming(struct rzg2l_cru_dev *cru)
> > > > > +{
> > > > > +     struct rzg2l_csi2 *csi2 = sd_to_csi2(cru->csi.subdev);
> > > > > +     u32 amnfifopntr, amnfifopntr_w, amnfifopntr_r_y;
> > > > > +     unsigned int retries = 0;
> > > > > +     unsigned long flags;
> > > > > +     u32 icnms;
> > > > > +
> > > > > +     cru->state = RZG2L_CRU_DMA_STOPPING;
> > > > > +
> > > > > +     rzg2l_cru_set_stream(cru, 0);
> > > > > +
> > > > > +     rzg2l_csi2_dphy_setting(csi2, 0);
> > > > > +
> > > > > +     rzg2l_csi2_mipi_link_setting(csi2, 0);
> > > > > +
> > > > > +     spin_lock_irqsave(&cru->qlock, flags);
> > > > > +
> > > > > +     /* Disable and clear the interrupt */
> > > > > +     rzg2l_cru_write(cru, CRUnIE, 0);
> > > > > +     rzg2l_cru_write(cru, CRUnINTS, 0x001F0F0F);
> > > > > +
> > > > > +     /* Stop the operation of image conversion */
> > > > > +     rzg2l_cru_write(cru, ICnEN, 0);
> > > > > +
> > > > > +     /* Wait for streaming to stop */
> > > > > +     while ((rzg2l_cru_read(cru, ICnMS) & ICnMS_IA) && retries++ < RZG2L_RETRIES) {
> > > > > +             spin_unlock_irqrestore(&cru->qlock, flags);
> > > > > +             msleep(RZG2L_TIMEOUT_MS);
> > > > > +             spin_lock_irqsave(&cru->qlock, flags);
> > > > > +     }
> > > > > +
> > > > > +     icnms = rzg2l_cru_read(cru, ICnMS) & ICnMS_IA;
> > > > > +     if (icnms)
> > > > > +             dev_err(cru->dev, "Failed stop HW, something is seriously broken\n");
> > > > > +
> > > > > +     cru->state = RZG2L_CRU_DMA_STOPPED;
> > > > > +
> > > > > +     /* Wait until the FIFO becomes empty */
> > > > > +     for (retries = 5; retries > 0; retries--) {
> > > > > +             amnfifopntr = rzg2l_cru_read(cru, AMnFIFOPNTR);
> > > > > +
> > > > > +             amnfifopntr_w = amnfifopntr & AMnFIFOPNTR_FIFOWPNTR;
> > > > > +             amnfifopntr_r_y =
> > > > > +                     (amnfifopntr & AMnFIFOPNTR_FIFORPNTR_Y) >> 16;
> > > > > +             if (amnfifopntr_w == amnfifopntr_r_y)
> > > > > +                     break;
> > > > > +
> > > > > +             usleep_range(10, 20);
> > > > > +     }
> > > > > +
> > > > > +     /* Notify that FIFO is not empty here */
> > > > > +     if (!retries)
> > > > > +             dev_err(cru->dev, "Failed to empty FIFO\n");
> > > > > +
> > > > > +     /* Stop AXI bus */
> > > > > +     rzg2l_cru_write(cru, AMnAXISTP, AMnAXISTP_AXI_STOP);
> > > > > +
> > > > > +     /* Wait until the AXI bus stop */
> > > > > +     for (retries = 5; retries > 0; retries--) {
> > > > > +             if (rzg2l_cru_read(cru, AMnAXISTPACK) &
> > > > > +                     AMnAXISTPACK_AXI_STOP_ACK)
> > > > > +                     break;
> > > > > +
> > > > > +             usleep_range(10, 20);
> > > > > +     };
> > > > > +
> > > > > +     /* Notify that AXI bus can not stop here */
> > > > > +     if (!retries)
> > > > > +             dev_err(cru->dev, "Failed to stop AXI bus\n");
> > > > > +
> > > > > +     /* Cancel the AXI bus stop request */
> > > > > +     rzg2l_cru_write(cru, AMnAXISTP, 0);
> > > > > +
> > > > > +     /* Resets the image processing module */
> > > > > +     rzg2l_cru_write(cru, CRUnRST, 0);
> > > > > +
> > > > > +     spin_unlock_irqrestore(&cru->qlock, flags);
> > > > > +
> > > > > +     /* Set reset state */
> > > > > +     reset_control_assert(cru->aresetn);
> > > > > +}
> > > > > +
> > > > > +static int rzg2l_cru_start_streaming_vq(struct vb2_queue *vq, unsigned int count)
> > > > > +{
> > > > > +     struct rzg2l_cru_dev *cru = vb2_get_drv_priv(vq);
> > > > > +     int ret;
> > > > > +
> > > > > +     /* Release reset state */
> > > > > +     ret = reset_control_deassert(cru->aresetn);
> > > > > +     if (ret) {
> > > > > +             dev_err(cru->dev, "failed to deassert aresetn\n");
> > > > > +             return ret;
> > > > > +     }
> > > > > +
> > > > > +     /* Allocate scratch buffer. */
> > > > > +     cru->scratch = dma_alloc_coherent(cru->dev, cru->format.sizeimage,
> > > > > +                                       &cru->scratch_phys, GFP_KERNEL);
> > > > > +     if (!cru->scratch) {
> > > > > +             return_unused_buffers(cru, VB2_BUF_STATE_QUEUED);
> > > > > +             dev_err(cru->dev, "Failed to allocate scratch buffer\n");
> > > > > +             return -ENOMEM;
> > > > > +     }
> > > > > +
> > > > > +     cru->sequence = 0;
> > > > > +
> > > > > +     ret = rzg2l_cru_set_stream(cru, 1);
> > > > > +     if (ret) {
> > > > > +             return_unused_buffers(cru, VB2_BUF_STATE_QUEUED);
> > > > > +             goto out;
> > > > > +     }
> > > > > +
> > > > > +     cru->state = RZG2L_CRU_DMA_STARTING;
> > > > > +
> > > > > +     dev_dbg(cru->dev, "Starting to capture\n");
> > > > > +
> > > > > +out:
> > > > > +     if (ret)
> > > > > +             dma_free_coherent(cru->dev, cru->format.sizeimage, cru->scratch,
> > > > > +                               cru->scratch_phys);
> > > > > +
> > > > > +     return ret;
> > > > > +}
> > > > > +
> > > > > +static void rzg2l_cru_stop_streaming_vq(struct vb2_queue *vq)
> > > > > +{
> > > > > +     struct rzg2l_cru_dev *cru = vb2_get_drv_priv(vq);
> > > > > +
> > > > > +     rzg2l_cru_stop_streaming(cru);
> > > > > +
> > > > > +     /* Free scratch buffer */
> > > > > +     dma_free_coherent(cru->dev, cru->format.sizeimage, cru->scratch,
> > > > > +                       cru->scratch_phys);
> > > > > +
> > > > > +     return_unused_buffers(cru, VB2_BUF_STATE_ERROR);
> > > > > +}
> > > > > +
> > > > > +static const struct vb2_ops rzg2l_cru_qops = {
> > > > > +     .queue_setup            = rzg2l_cru_queue_setup,
> > > > > +     .buf_prepare            = rzg2l_cru_buffer_prepare,
> > > > > +     .buf_queue              = rzg2l_cru_buffer_queue,
> > > > > +     .start_streaming        = rzg2l_cru_start_streaming_vq,
> > > > > +     .stop_streaming         = rzg2l_cru_stop_streaming_vq,
> > > > > +     .wait_prepare           = vb2_ops_wait_prepare,
> > > > > +     .wait_finish            = vb2_ops_wait_finish,
> > > > > +};
> > > > > +
> > > > > +static irqreturn_t rzg2l_cru_irq(int irq, void *data)
> > > > > +{
> > > > > +     struct rzg2l_cru_dev *cru = data;
> > > > > +     unsigned int handled = 0;
> > > > > +     unsigned long flags;
> > > > > +     u32 irq_status;
> > > > > +     u32 amnmbs;
> > > > > +     int slot;
> > > > > +
> > > > > +     spin_lock_irqsave(&cru->qlock, flags);
> > > > > +
> > > > > +     irq_status = rzg2l_cru_read(cru, CRUnINTS);
> > > > > +     if (!irq_status)
> > > > > +             goto done;
> > > > > +
> > > > > +     handled = 1;
> > > > > +
> > > > > +     rzg2l_cru_write(cru, CRUnINTS, rzg2l_cru_read(cru, CRUnINTS));
> > > > > +
> > > > > +     /* Nothing to do if capture status is 'RZG2L_CRU_DMA_STOPPED' */
> > > > > +     if (cru->state == RZG2L_CRU_DMA_STOPPED) {
> > > > > +             dev_dbg(cru->dev, "IRQ while state stopped\n");
> > > > > +             goto done;
> > > > > +     }
> > > > > +
> > > > > +     /* Increase stop retries if capture status is 'RZG2L_CRU_DMA_STOPPING' */
> > > > > +     if (cru->state == RZG2L_CRU_DMA_STOPPING) {
> > > > > +             if (irq_status & CRUnINTS_SFS)
> > > > > +                     dev_dbg(cru->dev, "IRQ while state stopping\n");
> > > > > +             goto done;
> > > > > +     }
> > > > > +
> > > > > +     /* Prepare for capture and update state */
> > > > > +     amnmbs = rzg2l_cru_read(cru, AMnMBS);
> > > > > +     slot = amnmbs & AMnMBS_MBSTS;
> > > > > +
> > > > > +     /*
> > > > > +      * AMnMBS.MBSTS indicates the destination of Memory Bank (MB).
> > > > > +      * Recalculate to get the current transfer complete MB.
> > > > > +      */
> > > > > +     if (slot == 0)
> > > > > +             slot = cru->num_buf - 1;
> > > > > +     else
> > > > > +             slot--;
> > > > > +
> > > > > +     /*
> > > > > +      * To hand buffers back in a known order to userspace start
> > > > > +      * to capture first from slot 0.
> > > > > +      */
> > > > > +     if (cru->state == RZG2L_CRU_DMA_STARTING) {
> > > > > +             if (slot != 0) {
> > > > > +                     dev_dbg(cru->dev, "Starting sync slot: %d\n", slot);
> > > > > +                     goto done;
> > > > > +             }
> > > > > +
> > > > > +             dev_dbg(cru->dev, "Capture start synced!\n");
> > > > > +             cru->state = RZG2L_CRU_DMA_RUNNING;
> > > > > +     }
> > > > > +
> > > > > +     /* Capture frame */
> > > > > +     if (cru->queue_buf[slot]) {
> > > > > +             cru->queue_buf[slot]->field = cru->format.field;
> > > > > +             cru->queue_buf[slot]->sequence = cru->sequence;
> > > > > +             cru->queue_buf[slot]->vb2_buf.timestamp = ktime_get_ns();
> > > > > +             vb2_buffer_done(&cru->queue_buf[slot]->vb2_buf,
> > > > > +                             VB2_BUF_STATE_DONE);
> > > > > +             cru->queue_buf[slot] = NULL;
> > > > > +     } else {
> > > > > +             /* Scratch buffer was used, dropping frame. */
> > > > > +             dev_dbg(cru->dev, "Dropping frame %u\n", cru->sequence);
> > > > > +     }
> > > > > +
> > > > > +     cru->sequence++;
> > > > > +
> > > > > +     /* Prepare for next frame */
> > > > > +     rzg2l_cru_fill_hw_slot(cru, slot);
> > > > > +
> > > > > +done:
> > > > > +     spin_unlock_irqrestore(&cru->qlock, flags);
> > > > > +
> > > > > +     return IRQ_RETVAL(handled);
> > > > > +}
> > > > > +
> > > > > +void rzg2l_cru_dma_unregister(struct rzg2l_cru_dev *cru)
> > > > > +{
> > > > > +     mutex_destroy(&cru->lock);
> > > > > +
> > > > > +     v4l2_device_unregister(&cru->v4l2_dev);
> > > > > +     reset_control_assert(cru->presetn);
> > > > > +}
> > > > > +
> > > > > +int rzg2l_cru_dma_register(struct rzg2l_cru_dev *cru, int irq)
> > > > > +{
> > > > > +     struct vb2_queue *q = &cru->queue;
> > > > > +     unsigned int i;
> > > > > +     int ret;
> > > > > +
> > > > > +     ret = reset_control_deassert(cru->presetn);
> > > > > +     if (ret) {
> > > > > +             dev_err(cru->dev, "failed to deassert presetn\n");
> > > > > +             return ret;
> > > > > +     }
> > > >
> > > > Shouldn't this be done when starting streaming instead ?
> > >
> > > Agreed, Ill move it there.
> > >
> > > > > +
> > > > > +     /* Initialize the top-level structure */
> > > > > +     ret = v4l2_device_register(cru->dev, &cru->v4l2_dev);
> > > > > +     if (ret)
> > > > > +             return ret;
> > > > > +
> > > > > +     mutex_init(&cru->lock);
> > > > > +     INIT_LIST_HEAD(&cru->buf_list);
> > > > > +
> > > > > +     spin_lock_init(&cru->qlock);
> > > > > +
> > > > > +     cru->state = RZG2L_CRU_DMA_STOPPED;
> > > > > +
> > > > > +     for (i = 0; i < HW_BUFFER_MAX; i++)
> > > > > +             cru->queue_buf[i] = NULL;
> > > > > +
> > > > > +     /* buffer queue */
> > > > > +     q->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
> > > > > +     q->io_modes = VB2_MMAP | VB2_READ | VB2_DMABUF;
> > > >
> > > > No VB2_READ please, that's very inefficient.
> > >
> > > OK, I'll drop it.
> > >
> > > > > +     q->lock = &cru->lock;
> > > > > +     q->drv_priv = cru;
> > > > > +     q->buf_struct_size = sizeof(struct rzg2l_cru_buffer);
> > > > > +     q->ops = &rzg2l_cru_qops;
> > > > > +     q->mem_ops = &vb2_dma_contig_memops;
> > > > > +     q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
> > > > > +     q->min_buffers_needed = 4;
> > > >
> > > > Does the hardware really require 4 buffers to operate ?
> > >
> > > v4l2-compliance complains about sequnce mismatch when set to 3.
> >
> > Then maybe there's another problem somewhere ? What's the minimum number
> > of buffers the hardware can operate with ?
> 
> FIFO depth is 16. We are using the similar code as rcar-vin where we
> use the scratch buffer (and also the rcar-vin sets the
> min_buffers_needed to 4)

Wow, that's a deep hardware FIFO !

What happens at the hardware level if a buffer completes and no other
buffer is present in the FIFO ?

-- 
Regards,

Laurent Pinchart



[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux