Hi! Jon Smirl "jonsmirl@xxxxxxxxx" wrote: > On Sun, Aug 1, 2010 at 5:50 AM, Christoph Bartelmus <lirc@xxxxxxxxxxxx> > wrote: >> Hi Jon, >> >> on 31 Jul 10 at 14:14, Jon Smirl wrote: >>> On Sat, Jul 31, 2010 at 1:47 PM, Christoph Bartelmus <lirc@xxxxxxxxxxxx> >>> wrote: >>>> Hi Jon, >>>> >>>> on 31 Jul 10 at 12:25, Jon Smirl wrote: >>>>> On Sat, Jul 31, 2010 at 11:12 AM, Andy Walls <awalls@xxxxxxxxxxxxxxxx> >>>>> wrote: >>>>>> I think you won't be able to fix the problem conclusively either way. >>>>>> A lot of how the chip's clocks should be programmed depends on how the >>>>>> GPIOs are used and what crystal is used. >>>>>> >>>>>> I suspect many designers will use some reference design layout from >>>>>> ENE, but it won't be good in every case. The wire-up of the ENE of >>>>>> various motherboards is likely something you'll have to live with as >>>>>> unknowns. >>>>>> >>>>>> This is a case where looser tolerances in the in kernel decoders could >>>>>> reduce this driver's complexity and/or get rid of arbitrary fudge >>>>>> factors in the driver. >>>> >>>>> The tolerances are as loose as they can be. The NEC protocol uses >>>>> pulses that are 4% longer than JVC. The decoders allow errors up to 2% >>>>> (50% of 4%). The crystals used in electronics are accurate to >>>>> 0.0001%+. >>>> >>>> But the standard IR receivers are far from being accurate enough to allow >>>> tolerance windows of only 2%. >>>> I'm surprised that this works for you. LIRC uses a standard tolerance of >>>> 30% / 100 us and even this is not enough sometimes. >>>> >>>> For the NEC protocol one signal consists of 22 individual pulses at >>>> 38kHz.. If the receiver just misses one pulse, you already have an error >>>> of 1/22 >>>>> 4%. >> >>> There are different types of errors. The decoders can take large >>> variations in bit times. The problem is with cumulative errors. In >>> this case the error had accumulated up to 450us in the lead pulse. >>> That's just too big of an error and caused the JVC code to be >>> misclassified as NEC. >>> >>> I think he said lirc was misclassifying it too. So we both did the same >>> thing. >> >> No way. JVC is a 16 bit code. NEC uses 32 bits. How can you ever confuse >> JVC with NEC signals? >> >> LIRC will work if there is a 4% or 40% or 400% error. Because irrecord >> generates the config file using your receiver it will compensate for any > At the end of the process we can build a record and match raw mode if > we have to. I'm not talking about raw mode here. lircd will happily decode the signals despite of any timing error as long it's consistent. I'm still interested how JVC can be confused with NEC codes. >> timing error. It will work with pulses cut down to 50 us like IrDA >> hardware does and it will work when half of the bits are swallowed like >> the IgorPlug USB receiver does. > The code for fixing IrDA and IgorPLug should live inside their low > level device drivers. The characteristics of the errors produced by > this hardware are known so a fix can be written to compensate. The function f(x) = 50 is not bijective. No way to compensate. Missing bits cannot be magically regenerated by the driver. > The > IgorPlug people might find it easier to fix their firmware. There is a firmware patch available? Do you have a pointer? Christoph -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
