Re: [PATCH v3 1/2] staging: media: ipu3: Fix AF x_start position when rightmost stripe is used

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Sakari,

On Wed, Mar 16, 2022 at 5:02 PM Sakari Ailus
<sakari.ailus@xxxxxxxxxxxxxxx> wrote:
>
> Hi Kate,
>
> On Mon, Mar 14, 2022 at 06:15:22PM +0800, Kate Hsuan wrote:
> > For the AF configuration, if the rightmost stripe is used, the AF scene
> > will be at the incorrect location of the sensor.
> >
> > The AF coordinate may be set to the right part of the sensor. This
> > configuration would lead to x_start being greater than the
> > down_scaled_stripes offset and the leftmost stripe would be disabled
> > and only the rightmost stripe is used to control the AF coordinate. If
> > the x_start doesn't perform any adjustments, the AF coordinate will be
> > at the wrong place of the sensor since down_scaled_stripes offset
> > would be the new zero of the coordinate system.
> >
> > In this patch, if only the rightmost stripe is used, x_start should
> > minus down_scaled_stripes offset to maintain its correctness of AF
> > scene coordinate.
> >
> > Changes in v2:
> > 1. Remove the setting of the first stripe.
> >
> > Signed-off-by: Kate Hsuan <hpa@xxxxxxxxxx>
> > ---
> >  drivers/staging/media/ipu3/ipu3-css-params.c | 4 ++++
> >  1 file changed, 4 insertions(+)
> >
> > diff --git a/drivers/staging/media/ipu3/ipu3-css-params.c b/drivers/staging/media/ipu3/ipu3-css-params.c
> > index d9e3c3785075..5a8c07f34756 100644
> > --- a/drivers/staging/media/ipu3/ipu3-css-params.c
> > +++ b/drivers/staging/media/ipu3/ipu3-css-params.c
> > @@ -2556,6 +2556,10 @@ int imgu_css_cfg_acc(struct imgu_css *css, unsigned int pipe,
> >               /* Enable only for rightmost stripe, disable left */
> >               acc->af.stripes[0].grid_cfg.y_start &=
> >                       ~IPU3_UAPI_GRID_Y_START_EN;
> > +             acc->af.stripes[1].grid_cfg.x_start -=
> > +                     acc->stripe.down_scaled_stripes[1].offset;
> > +             acc->af.stripes[1].grid_cfg.x_end -=
> > +                     acc->stripe.down_scaled_stripes[1].offset;
>
> Could you calculate the values the same way as for the two stripes case, as
> I've been asking since v1?

Sorry for my misunderstanding of the comments.
You mean x_end could be estimated by the width here and could use the
same way as for two stripes case to estimate this.
I'll correct this in my v4 patch. :)

Thank you.

>
> >       } else if (acc->af.config.grid_cfg.x_end <=
> >                  acc->stripe.bds_out_stripes[0].width - min_overlap) {
> >               /* Enable only for leftmost stripe, disable right */
>
> --
> Regards,
>
> Sakari Ailus
>


-- 
BR,
Kate




[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux