Hi,
I recently got an TechniSat SkyStar S2 [13d0:2103] which uses an
FlexCop2-Bridge, which is supported, but an unsupported? CX24120 Demod.
(This card is rather cheap, 45€ LowProfile incl. IR-Remote, otherwise i'd
just have sent it back.)
TechniSat provides a Binary Driver
(
http://www.technisat-daun.de/download/soft/soft_linux-driver_12-2008_6611.zip )
which contains an cx24120 blob (32/64) +Firmware, but requires an Dec2008
V4L-checkout (
I need a newer rev for my E3C EC168 USB-DVBT-Stick)
Anyway I can get this working? Can I help in any way?
Thanks,
Paul
lspci
Network controller: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip /
Technisat SkyStar2 DVB card (rev 02)
Subsystem: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip /
Technisat SkyStar2 DVB card
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 17
Region 0: Memory at feae0000 (32-bit, non-prefetchable) [size=64K]
Region 1: I/O ports at bc00 [size=32]
Kernel modules: b2c2-flexcop-pci
dmesg
[ 17.355268] b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver
chip loaded successfully
[ 17.357454] flexcop-pci: will use the HW PID filter.
[ 17.357460] flexcop-pci: card revision 2
[ 17.357469] b2c2_flexcop_pci 0000:05:04.0: PCI INT A -> GSI 17 (level,
low) -> IRQ 17
[ 17.391402] DVB: registering new adapter (FlexCop Digital TV device)
[ 17.393043] b2c2-flexcop: MAC address = xx:xx:xx:xx:d0:02
[ 17.393555] CX24123: wrong demod revision: 84
[ 17.628997] mt352_read_register: readreg error (reg=127, ret==-121)
[ 17.636769] nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err
== -121)
[ 17.636772] Unknown/Unsupported NXT chip: 00 00 00 00 00
[ 17.645121] lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02 error
(ret == -121)
[ 17.661886] stv0297_readreg: readreg error (reg == 0x80, ret == -121)
[ 17.671433] mt312_read: ret == -121
[ 17.671508] b2c2-flexcop: no frontend driver found for this B2C2/FlexCop
adapter
[ 17.671805] b2c2_flexcop_pci 0000:05:04.0: PCI INT A disabled
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
