[PATCH v2] media: vsp1: mask interrupts before enabling

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



VSP hardware could be used (e.g. by the bootloader) before driver load,
and some interrupts could be left in enabled and pending state. In this
case, setting up VSP interrupt handler without masking interrupts before
causes interrupt handler to be immediately called (and crash due to null
vsp->info dereference).

Fix that by explicitly masking all interrupts before setting the interrupt
handler. To do so, have to set the interrupt handler later, after hw
revision is already detected and number of interrupts to mask gets
known.

Based on patch by Koji Matsuoka <koji.matsuoka.xm@xxxxxxxxxxx> included
in the Renesas BSP kernel.

Signed-off-by: Nikita Yushchenko <nikita.yoush@xxxxxxxxxxxxxxxxxx>
---
v1: https://lore.kernel.org/all/20210926155356.23861-1-nikita.yoush@xxxxxxxxxxxxxxxxxx/
Changes since v1:
- move interrupt masking to a dedicated routine
- update comments and patch description

> I think I would rather see the code to reset them done in
> vsp1_reset_wpf(), rather than in probe directly as that is what we are
> doing, and is I believe already in the call path.

First, vsp1_reset_wpf() does not get called on driver early init.

It is normally called from within vsp1_device_get() when device is powered
on, but vsp1_probe() calls vsp1_device_get() when vsp1->info is not yet set,
and in this case call from vsp1_pm_runtime_resume() to vsp1_device_init() 
is skipped.

I've tried to add extra vsp1_device_put() / vsp1_device_get() calls to the
probe path, and dumped related registers in vsp1_pm_runtime_resume() after
return from vsp1_device_init(), and got

[    2.477315][    T1] vsp1 fea28000.vsp: VI6_DISP_IRQ_ENB(0) = 0x00000100
[    2.483933][    T1] vsp1 fea28000.vsp: VI6_DISP_IRQ_STA(0) = 0x00000121
[    2.490556][    T1] vsp1 fea28000.vsp: VI6_WPF_IRQ_ENB(0) = 0x00010002
[    2.497088][    T1] vsp1 fea28000.vsp: VI6_WPF_IRQ_STA(0) = 0x00010003
[    2.503618][    T1] vsp1 fea28000.vsp: VI6_WPF_IRQ_ENB(1) = 0x00000000
[    2.510148][    T1] vsp1 fea28000.vsp: VI6_WPF_IRQ_STA(1) = 0x00000000

which shows that
(1) WPF interrupt is not cleared by WPF reset,
(2) also DISP interrupt is enabled and pending, and driver does not seem
to control it at all.

Given that, I think it is safer to explicitly mask all interrupts before
setting the handler. I've moved interrupt masking to a separate routine.

> (But I'm reallly ... reallly concerned that the hardware is not really
> getting reset when it should, and that might merit some further
> investigation).

The documentation for WFP reset bit has notes that under some situations,
reset is postponed for a long time, and reported via interrupt. I'm not
sure what exactly goes on there, but I'd assume that such logic implies
that interrupt subsystem is not reset.

I agree that not having exact understand of hardware state is not good.
But, given that no signs of misfunction have been detected for a long time
(the patch was in vendor BSP for years), I think we can assume it is
"safe enough".

 drivers/media/platform/vsp1/vsp1_drv.c | 34 ++++++++++++++++++++------
 1 file changed, 26 insertions(+), 8 deletions(-)

diff --git a/drivers/media/platform/vsp1/vsp1_drv.c b/drivers/media/platform/vsp1/vsp1_drv.c
index c9044785b903..92a95e2c21c7 100644
--- a/drivers/media/platform/vsp1/vsp1_drv.c
+++ b/drivers/media/platform/vsp1/vsp1_drv.c
@@ -550,6 +550,16 @@ static int vsp1_device_init(struct vsp1_device *vsp1)
 	return 0;
 }
 
+static void vsp1_mask_all_interrupts(struct vsp1_device *vsp1)
+{
+	int i;
+
+	for (i = 0; i < vsp1->info->lif_count; ++i)
+		vsp1_write(vsp1, VI6_DISP_IRQ_ENB(i), 0);
+	for (i = 0; i < vsp1->info->wpf_count; ++i)
+		vsp1_write(vsp1, VI6_WPF_IRQ_ENB(i), 0);
+}
+
 /*
  * vsp1_device_get - Acquire the VSP1 device
  *
@@ -819,13 +829,6 @@ static int vsp1_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	ret = devm_request_irq(&pdev->dev, irq->start, vsp1_irq_handler,
-			      IRQF_SHARED, dev_name(&pdev->dev), vsp1);
-	if (ret < 0) {
-		dev_err(&pdev->dev, "failed to request IRQ\n");
-		return ret;
-	}
-
 	/* FCP (optional). */
 	fcp_node = of_parse_phandle(pdev->dev.of_node, "renesas,fcp", 0);
 	if (fcp_node) {
@@ -855,7 +858,6 @@ static int vsp1_probe(struct platform_device *pdev)
 		goto done;
 
 	vsp1->version = vsp1_read(vsp1, VI6_IP_VERSION);
-	vsp1_device_put(vsp1);
 
 	for (i = 0; i < ARRAY_SIZE(vsp1_device_infos); ++i) {
 		if ((vsp1->version & VI6_IP_VERSION_MODEL_MASK) ==
@@ -868,12 +870,28 @@ static int vsp1_probe(struct platform_device *pdev)
 	if (!vsp1->info) {
 		dev_err(&pdev->dev, "unsupported IP version 0x%08x\n",
 			vsp1->version);
+		vsp1_device_put(vsp1);
 		ret = -ENXIO;
 		goto done;
 	}
 
 	dev_dbg(&pdev->dev, "IP version 0x%08x\n", vsp1->version);
 
+	/*
+	 * Previous use of the hardware (e.g. by the bootloader) could leave
+	 * some interrupts enabled and pending.
+	 */
+	vsp1_mask_all_interrupts(vsp1);
+
+	vsp1_device_put(vsp1);
+
+	ret = devm_request_irq(&pdev->dev, irq->start, vsp1_irq_handler,
+			       IRQF_SHARED, dev_name(&pdev->dev), vsp1);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to request IRQ\n");
+		goto done;
+	}
+
 	/* Instantiate entities. */
 	ret = vsp1_create_entities(vsp1);
 	if (ret < 0) {
-- 
2.30.2




[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux