On 04.11.21 11:16, Irui Wang wrote:
On Thu, 2021-11-04 at 08:50 +0200, Dafna Hirschfeld wrote:
On 04.11.21 03:38, Irui Wang wrote:
Hi,
On Wed, 2021-11-03 at 22:50 +0200, Dafna Hirschfeld wrote:
On 09.08.21 12:12, Irui Wang (王瑞) wrote:
Hi Dafna,
2. Always happened issue ? timeout at the beginning
or in
processing ?
The commands that I run is:
sudo --user=#1000 /usr/local/libexec/chrome-binary-
tests/video_encode_accelerator_tests --gtest_filter=-
*NV12Dmabuf* -->>codec=vp8
/usr/local/share/tast/data/chromiumos/tast/local/bundles/
cros/
video/data/tulip2-320x180.yuv --disable_validator
The command sometime succeed but when I run it sequentially
then at some point after few attempts I start to get those
timeout errors.
It seems mean VP8 encoding function OK, but failed sometimes,
did
you have check VENC clock info during encoding:
cat /sys/kernel/debug/clk/clk_summary | grep venc:
venc_sel > it's H.264 clock
venclt_sel > it's VP8 clock
the enable&prepare count is not 0 during encoding process.
Thanks
Best Regards
-----邮件原件-----
发件人: Dafna Hirschfeld [mailto:dafna.hirschfeld@xxxxxxxxxxxxx]
发送时间: 2021年8月9日 16:27
收件人: Irui Wang (王瑞)
抄送: Linux Media Mailing List; moderated list:ARM/Mediatek SoC
support; Enric Balletbo i Serra
主题: Re: 答复: [PATCH 4/5] media: mtk-vcodec: Add two error cases
upon
vpu irq handling
On 09.08.21 09:37, Irui Wang (王瑞) wrote:
Hi Dafna,
I am testing the vp8 encoder on chromeos and at some
point
the encoder interrupts stop arriving so I try to figure
out
why and report any possible error.
1. Log shows wait IRQ timeout ?
Hi, yes, I get timeout when waiting to the encoder interrupt.
The
timeout is on vp8_enc_wait_venc_done
2. Always happened issue ? timeout at the beginning or in
processing ?
The commands that I run is:
sudo --user=#1000 /usr/local/libexec/chrome-binary-
tests/video_encode_accelerator_tests --gtest_filter=-
*NV12Dmabuf* --codec=vp8
/usr/local/share/tast/data/chromiumos/tast/local/bundles/cros/v
ideo
/data/tulip2-320x180.yuv --disable_validator
The command sometime succeed but when I run it sequentially
then at
some point after few attempts I start to get those timeout
errors.
3. how about IRQ infos?
cat /proc/interrupts | grep vcodec
18002000.vcodec >> it's H.264 encoder
19002000.vcodec >> it's VP8 encoder
I was told you have met another H.264 encoding failed
before,
did you find reasons about that ?
No,
But since I see that the google meetup uses the vp8 encoder I
decided to test the vp8 first.
[ 81.918747] [MTK_V4L2][ERROR]
mtk_vcodec_wait_for_done_ctx:32: [3] ctx->type=1, cmd=1,
wait_event_interruptible_timeout time=1000ms out 0 0!
[ 81.931392] [MTK_VCODEC][ERROR][3]: h264_encode_frame()
irq_status=0 failed
[ 81.938470] [MTK_V4L2][ERROR] mtk_venc_worker:1219:
venc_if_encode failed=-5
Hi,
I test the driver on debian now, I stream several instances of
vp8
and h264 in parallel.
I see that those errors always occur after an iommu page fault:
[gst-master] root@debian:~/gst-build# [ 5743.206014] mtk-iommu
10205000.iommu: fault type=0x5 iova=0xac2ff003 pa=0x0 larb=3
port=0
layer=1 write
[ 5744.204964] [MTK_V4L2][ERROR] mtk_vcodec_wait_for_done_ctx:32:
[2706] ctx->type=1, cmd=1, wait_event_interruptible_timeout
time=1000ms out 0 0!
[ 5744.217849] [MTK_VCODEC][ERROR][2706]: vp8_enc_encode_frame()
irq_status=0 failed
[ 5744.225359] [MTK_V4L2][ERROR] mtk_venc_worker:1243:
venc_if_encode
failed=-5
I suspect that maybe this is because the iova of the
working_buffers
is handed to the vpu in the function vp8_enc_alloc_work_buf:
wb[i].iova = inst->work_bufs[i].dma_addr;
Maybe the vpu keep writing to those addresses after they are
already
unmapped?
Thanks,
Dafna
failed larb=3, it's for h264 encoder, vp8 encoder is larb5, is
there
any h264 encoding failed at that time? I have no ideas why these
errors
happened on your platform, but when we got the "iommu: fault", the
possible reason is related to power or clock.
Once the iommu fault fires, both encoders constantly fail and never
recover
(also not when starting new instance).
With the falut:
mtk_iommu_isr: fault type=0x5 iova=0xebede003 pa=0x0 larb=3 port=0
layer=1 write
I looked at the iommu tracing log:
gst-launch-1.0-606 [000] ..... 714.634398: unmap: IOMMU:
iova=0x00000000ebede000 - 0x00000000ebedf000 size=4096
unmapped_size=4096
gst-launch-1.0-606 [000] ..... 714.634417: unmap: IOMMU:
iova=0x00000000ebed0000 - 0x00000000ebed5000 size=20480
unmapped_size=20480
gst-launch-1.0-606 [000] ..... 714.634435: unmap: IOMMU:
iova=0x00000000eb800000 - 0x00000000ebb0a000 size=3186688
unmapped_size=3186688
gst-launch-1.0-606 [000] .N... 714.634891: unmap: IOMMU:
iova=0x00000000eb700000 - 0x00000000eb7ff000 size=1044480
unmapped_size=1044480
gst-launch-1.0-606 [000] .N... 714.635481: unmap: IOMMU:
iova=0x00000000eb000000 - 0x00000000eb30a000 size=3186688
unmapped_size=3186688
gst-launch-1.0-606 [000] ..... 714.635934: unmap: IOMMU:
iova=0x00000000eaf00000 - 0x00000000eafff000 size=1044480
unmapped_size=1044480
gst-launch-1.0-606 [000] ..... 714.636041: unmap: IOMMU:
iova=0x00000000eaef0000 - 0x00000000eaf00000 size=65536
unmapped_size=65536
gst-launch-1.0-606 [000] ..... 714.636056: unmap: IOMMU:
iova=0x00000000eaee0000 - 0x00000000eaef0000 size=65536
unmapped_size=65536
gst-launch-1.0-606 [000] ..... 714.636069: unmap: IOMMU:
iova=0x00000000eaedf000 - 0x00000000eaee0000 size=4096
unmapped_size=4096
kworker/0:0-537 [000] d.h.. 714.636191: io_page_fault:
IOMMU:mtk-iommu 10205000.iommu iova=0x00000000ebede003 flags=0x0001
(I changed the iommu map/unmap trace events to print the iova range)
you can see the first line unmapping 00000000ebede000 which is the
faulting iova.
So it seems that the problem is due to a device trying to access an
address that is already unmapped.
This might be either the encoder or the vpu.
Since the wb[i].iova is not reset when freeing the working buffers I
suspect it might be the vpu device, what do you think?
Thanks,
Dafna
vpu device won't access the address, the fault logs:
Looking at the line:
wb[i].iova = wb[i].iova = inst->work_bufs[i].dma_addr;
in both vp8 and h264 it seems that the codec drivers give the vpu access to the allocated iova address.
If the vpu doesn't access those addresses then what is the purpose of this line?
fault type=0x5 iova=0xebede003 pa=0x0 larb=3 port=0 layer=1 write
it's h264 encoder error when writing "RCPU" data address to encoder
hardware through iommu, but why unmap happended at this time? it seems
encoding process still going on....
Why is it seems so?
MT8173 latest VPUD firmware:
https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmwar
e.git/commit/?id=aaed4a8bf9a77ec68376e8d92fb218d5fdd88b59
I uses the latest firmware.
Thanks,
Dafna
Thanks
Best Regards
-----邮件原件-----
发件人: Dafna Hirschfeld [mailto:dafna.hirschfeld@xxxxxxxxxxxxx]
发送时间: 2021年8月6日 15:49
收件人: Irui Wang (王瑞); linux-kernel@xxxxxxxxxxxxxxx;
linux-media@xxxxxxxxxxxxxxx;
linux-mediatek@xxxxxxxxxxxxxxxxxxx
抄送: dafna3@xxxxxxxxx; tfiga@xxxxxxxxxxxx; Tiffany Lin (林慧珊);
eizan@xxxxxxxxxxxx; Maoguang Meng (孟毛广); kernel@xxxxxxxxxxxxx
;
mchehab@xxxxxxxxxx; hverkuil@xxxxxxxxx; Yunfei Dong (董云飞);
Yong
Wu
(吴勇); hsinyi@xxxxxxxxxxxx; matthias.bgg@xxxxxxxxx; Andrew-CT
Chen
(陳智迪); acourbot@xxxxxxxxxxxx
主题: Re: [PATCH 4/5] media: mtk-vcodec: Add two error cases
upon
vpu
irq handling
On 06.08.21 08:58, Irui Wang (王瑞) wrote:
On Wed, 2021-08-04 at 16:27 +0200, Dafna Hirschfeld wrote:
1. Fail if the function mtk_vcodec_fw_map_dm_addr returns
ERR
pointer.
2. Fail if the state from the vpu msg is either
VEN_IPI_MSG_ENC_STATE_ERROR or VEN_IPI_MSG_ENC_STATE_PART
Signed-off-by: Dafna Hirschfeld <
dafna.hirschfeld@xxxxxxxxxxxxx>
---
drivers/media/platform/mtk-vcodec/venc_vpu_if.c | 8
++++++++
1 file changed, 8 insertions(+)
diff --git a/drivers/media/platform/mtk-
vcodec/venc_vpu_if.c
b/drivers/media/platform/mtk-vcodec/venc_vpu_if.c
index 32dc844d16f9..234705ba7cd6 100644
--- a/drivers/media/platform/mtk-vcodec/venc_vpu_if.c
+++ b/drivers/media/platform/mtk-vcodec/venc_vpu_if.c
@@ -17,6 +17,8 @@ static int handle_enc_init_msg(struct
venc_vpu_inst *vpu, const void *data)
vpu->vsi = mtk_vcodec_fw_map_dm_addr(vpu->ctx->dev-
fw_handler,
msg->vpu_inst_addr);
+if (IS_ERR(vpu->vsi))
+return PTR_ERR(vpu->vsi);
/* Firmware version field value is unspecified on
MT8173.
*/
if (vpu->ctx->dev->venc_pdata->chip == MTK_MT8173)
return 0;
@@ -42,6 +44,12 @@ static int
handle_enc_encode_msg(struct
venc_vpu_inst *vpu, const void *data)
vpu->state = msg->state;
vpu->bs_size = msg->bs_size;
vpu->is_key_frm = msg->is_key_frm;
+if (vpu->state == VEN_IPI_MSG_ENC_STATE_ERROR ||
+ vpu->state == VEN_IPI_MSG_ENC_STATE_PART) {
mtk_vcodec_err(vpu,
+"bad ipi-enc-state: %s",
+ vpu->state ==
VEN_IPI_MSG_ENC_STATE_ERROR ? "ERR" : "PART");
+return -EINVAL;
+}
Hi Dafna,
This state check is useless, the enc result will check in
"vpu_enc_ipi_handler".
Hi, thanks for reviewing. I see that the vpu_enc_ipi_handler
only
test the msg->status and I see that the states are not tested
anywhere except of "skip" state in the h264 enc.
Can't there be a scenario where msg->status is ok but the
state
is error?
I am testing the vp8 encoder on chromeos and at some point
the
encoder interrupts stop arriving so I try to figure out why
and
report any possible error.
Thanks,
Dafna
Thanks
return 0;
}
************* MEDIATEK Confidentiality Notice
******************** The
information contained in this e-mail message (including any
attachments) may be confidential, proprietary, privileged, or
otherwise exempt from disclosure under applicable laws. It is
intended
to be conveyed only to the designated recipient(s). Any use,
dissemination, distribution, printing, retaining or copying
of
this
e-mail (including its
attachments) by unintended recipient(s) is strictly
prohibited
and may
be unlawful. If you are not an intended recipient of this e-
mail,
or
believe that you have received this e-mail in error, please
notify the
sender immediately (by replying to this e-mail), delete any
and
all
copies of this e-mail (including any attachments) from your
system,
and do not disclose the content of this e-mail to any other
person. Thank you!
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/linux-mediatek
