On 27/05/2021 19:06, Pratyush Yadav wrote:
Hi Tomi,
On 24/05/21 02:09PM, Tomi Valkeinen wrote:
Add routing and stream_config support to CAL driver.
Add multiplexed streams support. CAL has 8 dma-engines and can capture 8
separate streams at the same time.
Add 8 video device nodes, each representing a single dma-engine, and set
the number of source pads on camerarx to 8. Each video node can be
connected to any of the source pads on either of the camerarx instances
using media links. Camerarx internal routing is used to route the
incoming CSI-2 streams to one of the 8 source pads.
CAL doesn't support transcoding, so the driver currently allows changes
only on the camerarx sink side, and then copies the sink pad config to
the source pad. This becomes slighly more complex with 8 source pads and
multiple streams on the sink pad. A helper,
cal_camerarx_get_opposite_stream_format(), is added, which uses the
routing table to get the format from the "opposite" side.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@xxxxxxxxxxxxxxxx>
---
drivers/media/platform/ti-vpe/cal-camerarx.c | 303 ++++++++++++++++---
drivers/media/platform/ti-vpe/cal-video.c | 103 ++++++-
drivers/media/platform/ti-vpe/cal.c | 34 ++-
drivers/media/platform/ti-vpe/cal.h | 12 +-
4 files changed, 385 insertions(+), 67 deletions(-)
[...]
@@ -1178,18 +1177,33 @@ static int cal_probe(struct platform_device *pdev)
}
/* Create contexts. */
- for (i = 0; i < cal->data->num_csi2_phy; ++i) {
- if (!cal->phy[i]->source_node)
- continue;
+ if (!cal_mc_api) {
+ for (i = 0; i < cal->data->num_csi2_phy; ++i) {
+ if (!cal->phy[i]->source_node)
+ continue;
+
+ cal->ctx[i] = cal_ctx_create(cal, i);
+ if (!cal->ctx[i]) {
+ cal_err(cal, "Failed to create context %u\n", i);
+ ret = -ENODEV;
+ goto error_context;
+ }
- cal->ctx[i] = cal_ctx_create(cal, i);
- if (!cal->ctx[i]) {
- cal_err(cal, "Failed to create context %u\n", i);
- ret = -ENODEV;
- goto error_context;
+ cal->ctx[i]->phy = cal->phy[i];
+
+ cal->num_contexts++;
}
+ } else {
+ for (i = 0; i < ARRAY_SIZE(cal->ctx); ++i) {
+ cal->ctx[i] = cal_ctx_create(cal, i);
+ if (!cal->ctx[i]) {
+ cal_err(cal, "Failed to create context %u\n", i);
+ ret = -ENODEV;
+ goto error_context;
+ }
- cal->num_contexts++;
+ cal->num_contexts++;
In cal_async_notifier_complete() I see:
for (i = 0; i < cal->num_contexts; i++)
ret = cal_ctx_v4l2_register();
This means that if the CAL device has 8 DMA contexts it will create 8
/dev/videoX nodes, even if the hardware setup is only capable of 1
stream.
Would it make more sense to populate /dev/videoX nodes based on the
configured routing? So for example, if only one pad is being used to
output, only create one node corresponding to that pad. If there are 3
pads being populated then create 3 nodes and so on.
Routing is a runtime configuration, so it could mean creating or
removing video nodes every time the user changes the routing. I believe
video nodes are supposed to be more permanent than that.
If we knew that the HW setup can only ever have N routes, we could limit
the number of video nodes, but I don't think we have means to figure
that out.
Tomi
