On 22.12.20 16:55, Martin Kepplinger wrote:
On 22.12.20 16:35, Laurent Pinchart wrote:
Hi Martin,
On Tue, Dec 22, 2020 at 03:06:28PM +0100, Martin Kepplinger wrote:
On 10.12.20 17:04, Laurent Pinchart wrote:
On Thu, Dec 10, 2020 at 02:12:30PM +0100, Martin Kepplinger wrote:
On 10.12.20 13:17, Laurent Pinchart wrote:
On Thu, Dec 10, 2020 at 11:24:00AM +0200, Laurent Pinchart wrote:
On Thu, Dec 10, 2020 at 09:17:48AM +0100, Martin Kepplinger wrote:
hi,
TL;DR: did you use the NXP "mx6s_capture" csi bridge driver with
other
cameras?
I've recently worked on camera support for i.MX8MM (whose camera IP
cores are, if not identical, very similar to the i.MX8MQ's). The
least I
can say is that it was painful :-(
I'm using an MT9M114 sensor, which can produce RAW8, RAW10 and
YUV and
has a CSI-2 interface. My first use case is to capture RAW10, which
isn't supported by the mx6s_capture driver.
so did you successfully use the NXP mx6s_capture driver with that
sensor
too?
I haven't tried. The mx6s_capture driver and the mainline driver
share a
similar architecture, as they came from the same code base. They have
diverged, with the mainline driver receiving bug fixes and new
features, and my large no-yet-upstreamed patch series adds lots of
fixes
that are required for the mt9m114 driver to work with the driver. For
that reason, I've considered that porting the mt9m114 driver to the NXP
mx6s_capture, and fixing the same issues in the mx6s_capture driver
than
were present in the mainline driver, would require lots of time for
likely very little gain.
That being said, I've compared the two drivers, and I haven't seen
anything in mx6s_capture that would address the specific issues I'm
facing. I've ordered yesterday an i.MX8MM EVK with an OV5640 camera
module, and I will test those with the mainline driver. If they don't
work, and assuming the NXP kernel driver works on that platform, I'll
have two code bases to compare.
I try to use a CSI2 camera (hi846 I'm writing a driver for) on
imx8mq:
Using NXP's CSI bridge driver
https://source.codeaurora.org/external/imx/linux-imx/tree/drivers/media/platform/mxc/capture/mx6s_capture.c?h=imx_5.4.0_8dxlphantom_er
as well as the CSI driver itself:
https://source.codeaurora.org/external/imx/linux-imx/tree/drivers/media/platform/imx8/mxc-mipi-csi2_yav.c?h=imx_5.4.0_8dxlphantom_er
works fine when using the ov5640 camera with this driver:
https://source.codeaurora.org/external/imx/linux-imx/tree/drivers/media/platform/mxc/capture/ov5640_mipi_v2.c?h=imx_5.4.0_8dxlphantom_er
(I realize there is a CSI bridge driver in staging, but that
need more
work to be actually used. Of course after this the goal is to
fix and
use it; and mainline a CSI phy driver too.)
I have lots of patches for this driver, which I've developed on
i.MX7D
for a separate project. I'd like to mainline them, but this is
blocked
by one last issue that I haven't been able to solve yet. In a
nutshell,
the CSI writes two consecutive frames in each buffer, overflowing
the
allocated memory. The registers that control the buffer size seem
to be
programmed correctly as far as I can tell. I've reported this
issue to
NXP but haven't received any feedback yet.
that's different from where I am. So you don't get any interrupt
(EOF or
other) when only *one* frame is written into one buffer?
I don't get any FB1_DMA_DONE or FB2_DMA_DONE interrupt at least. I
haven't checked other interrupts. I thus get half of the frame rate. If
I configure the CSI_CSIIMAG_PARA register with half of the actual image
height, buffers then contain a single image and the frame rate goes to
the expected value. That gives me a workaround, but without
understanding the root cause, I'm worried that just halving the height
would introduce other breakages.
Hi Laurent,
Thanks a lot, exchanging things this way alone is much appreciated. I'll
give you detailed feedback on the staging drivers later - I tried
running them, they probe but still a (gstreamer) stream would not start.
But most all of your addition make a lot of sense.
Just so you know, to emphasize that once more: I'm still on the nxp
drivers (yes, they are very similar) just because the ov56 cam works
with them over here.
I've recently bought an i.MX8MM EVK, with the OV5647 camera module, and
when I try to capture images, with the NXP kernel, I just don't get any.
*sigh* I'll have to debug that.
oh you have it already. very good.
I guess the nxp kernel directly *should* work, but I use a kernel based
on v5.9.X and include the drivers like so:
https://source.puri.sm/Librem5/linux-next/-/commit/ed8f567432d776d21cb7160c03e3272826a5f316
https://source.puri.sm/Librem5/linux-next/-/commit/8d93a2cfd485d404741560dcb2f22da548f54ebc
The main problem I have is that, as soon as I try
to use a different pixelformat than V4L2_PIX_FMT_YUYV that basically
nothing works anymore. userspace stops to "be interested" pretty soon.
If I do (wrongly) use that pixelformat, I do get (only) one frame (dma)
completed, the usual way.
And when I break the ov56 by using a wrong pixelformat in mx6s_capture
(nxp bridge driver), I get equally get only one frame (dma) completed
there.
How can I make this thing use a different pixelformat (by setting the
media bus format in the sensor driver)?
All the components have to support the format you want to capture. This
includes the CSI driver, the MIPI_CSI driver, and the OV5647 driver. The
pixel format only matters in the CSI driver, for the other two it's the
media bus format that matters. To capture raw bayer data, you'll first
need to extend the OV5640 driver to support the corresponding media bus
format (and of course configure the sensor to output that format), then
the MIPI_CSI driver to support that media bus format as well, and
finally the CSI driver.
ok, the sensor I work with outputs raw bayer only, and that sounds like
I should pay more attention to the mipi csi driver.
that links to my experiments I occasionally update:
https://source.puri.sm/martin.kepplinger/linux-next/-/commits/hi846
thanks again for sharing your code early. have a nice rest of the year,
thanks,
martin
hi Laurent, how are you? Am I right in that you tried to run the ov5640
mainline driver with the CSI bridge staging driver on imx8mq? Which mipi
driver would you then use? Did you have progress in that area and in
resolving things in order to push some of your changes out?
I'm still struggling with the different sensor I want to use on imx8mq
(hi846) and I still use the nxp bsp drivers for mipi and csi bridge:
I was able to add and fix a few things and get some kind of image at
least, but there's still definitely some sizes or timings wrong (in
every resolution mode I think). 1280x720 shows it clearly as the image
looks "almost" normal only when I resize it to 916 pixel width. Also, it
"shifts" with later frames. For a few images of this, see
https://source.puri.sm/Librem5/linux-next/-/issues/43#note_143875
I just wanted to describe the above just in case you've seen something
like that during your experiments with sensors and can point me to
places to look at. I do think that the SoC side should be ok now (but
still now 100% sure), but many sensors are similar and maybe you have
ideas there too.
anyways, thanks for looking at this and as soon as I have a satisfying
image with my current setup, I'll switch to the staging csi driver. But
there's no driver for the mipi ("phy") in staging for imx8mq, right?
thanks!
martin
