On 10.12.20 17:04, Laurent Pinchart wrote:
Hi Martin,
On Thu, Dec 10, 2020 at 02:12:30PM +0100, Martin Kepplinger wrote:
On 10.12.20 13:17, Laurent Pinchart wrote:
On Thu, Dec 10, 2020 at 11:24:00AM +0200, Laurent Pinchart wrote:
On Thu, Dec 10, 2020 at 09:17:48AM +0100, Martin Kepplinger wrote:
hi,
TL;DR: did you use the NXP "mx6s_capture" csi bridge driver with other
cameras?
I've recently worked on camera support for i.MX8MM (whose camera IP
cores are, if not identical, very similar to the i.MX8MQ's). The least I
can say is that it was painful :-(
I'm using an MT9M114 sensor, which can produce RAW8, RAW10 and YUV and
has a CSI-2 interface. My first use case is to capture RAW10, which
isn't supported by the mx6s_capture driver.
so did you successfully use the NXP mx6s_capture driver with that sensor
too?
I haven't tried. The mx6s_capture driver and the mainline driver share a
similar architecture, as they came from the same code base. They have
diverged, with the mainline driver receiving bug fixes and new
features, and my large no-yet-upstreamed patch series adds lots of fixes
that are required for the mt9m114 driver to work with the driver. For
that reason, I've considered that porting the mt9m114 driver to the NXP
mx6s_capture, and fixing the same issues in the mx6s_capture driver than
were present in the mainline driver, would require lots of time for
likely very little gain.
That being said, I've compared the two drivers, and I haven't seen
anything in mx6s_capture that would address the specific issues I'm
facing. I've ordered yesterday an i.MX8MM EVK with an OV5640 camera
module, and I will test those with the mainline driver. If they don't
work, and assuming the NXP kernel driver works on that platform, I'll
have two code bases to compare.
I try to use a CSI2 camera (hi846 I'm writing a driver for) on imx8mq:
Using NXP's CSI bridge driver
https://source.codeaurora.org/external/imx/linux-imx/tree/drivers/media/platform/mxc/capture/mx6s_capture.c?h=imx_5.4.0_8dxlphantom_er
as well as the CSI driver itself:
https://source.codeaurora.org/external/imx/linux-imx/tree/drivers/media/platform/imx8/mxc-mipi-csi2_yav.c?h=imx_5.4.0_8dxlphantom_er
works fine when using the ov5640 camera with this driver:
https://source.codeaurora.org/external/imx/linux-imx/tree/drivers/media/platform/mxc/capture/ov5640_mipi_v2.c?h=imx_5.4.0_8dxlphantom_er
(I realize there is a CSI bridge driver in staging, but that need more
work to be actually used. Of course after this the goal is to fix and
use it; and mainline a CSI phy driver too.)
I have lots of patches for this driver, which I've developed on i.MX7D
for a separate project. I'd like to mainline them, but this is blocked
by one last issue that I haven't been able to solve yet. In a nutshell,
the CSI writes two consecutive frames in each buffer, overflowing the
allocated memory. The registers that control the buffer size seem to be
programmed correctly as far as I can tell. I've reported this issue to
NXP but haven't received any feedback yet.
that's different from where I am. So you don't get any interrupt (EOF or
other) when only *one* frame is written into one buffer?
I don't get any FB1_DMA_DONE or FB2_DMA_DONE interrupt at least. I
haven't checked other interrupts. I thus get half of the frame rate. If
I configure the CSI_CSIIMAG_PARA register with half of the actual image
height, buffers then contain a single image and the frame rate goes to
the expected value. That gives me a workaround, but without
understanding the root cause, I'm worried that just halving the height
would introduce other breakages.
Hi Laurent,
Thanks a lot, exchanging things this way alone is much appreciated. I'll
give you detailed feedback on the staging drivers later - I tried
running them, they probe but still a (gstreamer) stream would not start.
But most all of your addition make a lot of sense.
Just so you know, to emphasize that once more: I'm still on the nxp
drivers (yes, they are very similar) just because the ov56 cam works
with them over here. The main problem I have is that, as soon as I try
to use a different pixelformat than V4L2_PIX_FMT_YUYV that basically
nothing works anymore. userspace stops to "be interested" pretty soon.
If I do (wrongly) use that pixelformat, I do get (only) one frame (dma)
completed, the usual way.
And when I break the ov56 by using a wrong pixelformat in mx6s_capture
(nxp bridge driver), I get equally get only one frame (dma) completed there.
How can I make this thing use a different pixelformat (by setting the
media bus format in the sensor driver)?
thanks again for sharing your code early. have a nice rest of the year,
martin
