Hi Sakari,
Thanks for your patch.
On 2020-09-30 17:48:10 +0300, Sakari Ailus wrote:
> Rework the documentation of v4l2_fwnode_endpoint_parse for better
> readability, usefulness and correctness.
>
> Signed-off-by: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@xxxxxxxxxxxx>
> ---
> include/media/v4l2-fwnode.h | 62 ++++++++++++++++++++++++-------------
> 1 file changed, 40 insertions(+), 22 deletions(-)
>
> diff --git a/include/media/v4l2-fwnode.h b/include/media/v4l2-fwnode.h
> index 0f9a768b1a8d..0c28dc11e829 100644
> --- a/include/media/v4l2-fwnode.h
> +++ b/include/media/v4l2-fwnode.h
> @@ -219,17 +219,26 @@ struct v4l2_fwnode_connector {
> * @vep: pointer to the V4L2 fwnode data structure
> *
> * This function parses the V4L2 fwnode endpoint specific parameters from the
> - * firmware. The caller is responsible for assigning @vep.bus_type to a valid
> - * media bus type. The caller may also set the default configuration for the
> - * endpoint --- a configuration that shall be in line with the DT binding
> - * documentation. Should a device support multiple bus types, the caller may
> - * call this function once the correct type is found --- with a default
> - * configuration valid for that type.
> - *
> - * It is also allowed to set @vep.bus_type to V4L2_MBUS_UNKNOWN. USING THIS
> - * FEATURE REQUIRES "bus-type" PROPERTY IN DT BINDINGS. For old drivers,
> - * guessing @vep.bus_type between CSI-2 D-PHY, parallel and BT.656 busses is
> - * supported. NEVER RELY ON GUESSING @vep.bus_type IN NEW DRIVERS!
> + * firmware. There are two ways to use this function, either by letting it
> + * obtain the type of the bus (by setting the @vep.bus_type field to
> + * V4L2_MBUS_UNKNOWN) or specifying the bus type explicitly to one of the &enum
> + * v4l2_mbus_type types.
> + *
> + * When @vep.bus_type is V4L2_MBUS_UNKNOWN, the function will use the "bus-type"
> + * property to determine the type when it is available. The caller is
> + * responsible for validating the contents of @vep.bus_type field after the call
> + * returns.
> + *
> + * As a deprecated functionality to support older DT bindings without "bus-type"
> + * property for devices that support multiple types, if the "bus-type" property
> + * does not exist, the function will attempt to guess the type based on the
> + * endpoint properties available. NEVER RELY ON GUESSING THE BUS TYPE IN NEW
> + * DRIVERS OR BINDINGS.
> + *
> + * It is also possible to set @vep.bus_type corresponding to an actual bus. In
> + * this case the function will only attempt to parse properties related to this
> + * bus, and it will return an error if the value of the "bus-type" property
> + * corresponds to a different bus.
> *
> * The caller is required to initialise all fields of @vep.
> *
> @@ -263,17 +272,26 @@ void v4l2_fwnode_endpoint_free(struct v4l2_fwnode_endpoint *vep);
> * @vep: pointer to the V4L2 fwnode data structure
> *
> * This function parses the V4L2 fwnode endpoint specific parameters from the
> - * firmware. The caller is responsible for assigning @vep.bus_type to a valid
> - * media bus type. The caller may also set the default configuration for the
> - * endpoint --- a configuration that shall be in line with the DT binding
> - * documentation. Should a device support multiple bus types, the caller may
> - * call this function once the correct type is found --- with a default
> - * configuration valid for that type.
> - *
> - * It is also allowed to set @vep.bus_type to V4L2_MBUS_UNKNOWN. USING THIS
> - * FEATURE REQUIRES "bus-type" PROPERTY IN DT BINDINGS. For old drivers,
> - * guessing @vep.bus_type between CSI-2 D-PHY, parallel and BT.656 busses is
> - * supported. NEVER RELY ON GUESSING @vep.bus_type IN NEW DRIVERS!
> + * firmware. There are two ways to use this function, either by letting it
> + * obtain the type of the bus (by setting the @vep.bus_type field to
> + * V4L2_MBUS_UNKNOWN) or specifying the bus type explicitly to one of the &enum
> + * v4l2_mbus_type types.
> + *
> + * When @vep.bus_type is V4L2_MBUS_UNKNOWN, the function will use the "bus-type"
> + * property to determine the type when it is available. The caller is
> + * responsible for validating the contents of @vep.bus_type field after the call
> + * returns.
> + *
> + * As a deprecated functionality to support older DT bindings without "bus-type"
> + * property for devices that support multiple types, if the "bus-type" property
> + * does not exist, the function will attempt to guess the type based on the
> + * endpoint properties available. NEVER RELY ON GUESSING THE BUS TYPE IN NEW
> + * DRIVERS OR BINDINGS.
> + *
> + * It is also possible to set @vep.bus_type corresponding to an actual bus. In
> + * this case the function will only attempt to parse properties related to this
> + * bus, and it will return an error if the value of the "bus-type" property
> + * corresponds to a different bus.
> *
> * The caller is required to initialise all fields of @vep.
> *
> --
> 2.27.0
>
>
--
Regards,
Niklas Söderlund
