On 03/15/10 07:51, Andy Walls wrote:
On Sun, 2010-03-14 at 22:48 -0400, Mark Lord wrote:
..
Digging through google, it appears this problem has been around as long
as the cx18 driver has existed, with no clear resolution. Lots of people
have reported it to you before, and nobody has found a silver bullet fix.
Correct. I thought it was completely gone, but apparently, there just
isn't a lot of reporting of this intermittent problem.
..
If the audio is not working after modprobe, then simply doing rmmod/modprobe
in a loop (until working audio is achieved) is enough to cure it.
..
Well, crap. Tonight our MythTV box proved that assertion to be false.
The cx18 audio was okay after modprobe, but went bad a few seconds later,
when mythbackend started up and did the initial channel tuning.
I have a script that attempts audio input toggling when that happens,
but it had no effect. rmmod/modprobe is still the only "solution",
and it's rather difficult to do those while mythbackend is running.
Here are all the potential problem areas I can think of:
1. A/V digitizer/decoder audio detection firmware load and init. (I've
added firmware readback verification to try and head this off.)
2. A/V digitizer decoder audio microcontroller hard reset and "soft"
reset sequencing. (I think the cx18 driver has this wrong ATM.)
3. APU load and init. (The double load is to fix a DTV TS stream bug on
every other APU& CPU firmware load sequence. The APU_AI_RESET is to
fix the audio bitrate problem on first capture after a double firmware
load.)
4. AI1 Mux setting failing when switching between the internal A/V
decoder's I2S output and the external I2S inputs. (I thought I had this
fixed, but I don't have detailed register specs for that register - so
maybe not.)
5. A/V decoder audio clock PLL stops operating due to being programmed
out of range. (This was a problem for 32 ksps audio a while ago, but
I'm pretty confident I have it fixed.)
6. A/V decoder analog frontend setup for SIF wrong?. (I fixed this due
to a problen Helen Buus reported with cable TV.)
I think #2 is the real problem. I just started to disassmble the
digitizer firmware 2 nights ago to see if I could get some insight as to
how to properly reset it.
I've got a first WAG at fixing the resets of the audio microcontroller's
resets at:
http://linuxtv.org/hg/~awalls/cx18-audio
If it doesn't work, change the CXADEC_AUDIO_SOFT_RESET register define
from 0x810 to 0x9cc, although that may not work either.
..
I'll have a go at that, and anything else you can dream up as well.
But not for a few days -- really really crazy busy at work right now.
I am a Linux kernel developer, so I can handle patches and stuff
if you have any to offer.
Oh.. attached is a full log from a failure a few nights ago.
This one has the full card status dump included, which shows
where the audio is being muted at.
...
With that said, the CX23418 will sometimes have to let register access
over the PCI bus fail. For that, I have routines in cx18-io.[ch] to
perform retries. You may wish to add a log statement there to watch for
retry loops that completely fail.
..
I did that a while ago, and they didn't trigger back then.
Thanks
Mark
Mar 13 14:29:55 duke syslogd 1.5.0#2ubuntu6: restart.
Mar 13 14:29:56 duke ntpdate[3172]: step time server 10.0.0.2 offset 0.903835 sec
Mar 13 14:29:56 duke ntpd[3542]: ntpd 4.2.4p4@xxxxxxxx Fri Dec 4 19:14:37 UTC 2009 (1)
Mar 13 14:29:56 duke ntpd[3550]: precision = 1.000 usec
Mar 13 14:29:56 duke ntpd[3550]: Listening on interface #0 wildcard, 0.0.0.0#123 Disabled
Mar 13 14:29:56 duke ntpd[3550]: Listening on interface #1 lo, 127.0.0.1#123 Enabled
Mar 13 14:29:56 duke ntpd[3550]: Listening on interface #2 eth0, 10.0.0.18#123 Enabled
Mar 13 14:29:56 duke ntpd[3550]: Listening on interface #3 eth1, 169.254.4.100#123 Enabled
Mar 13 14:29:56 duke ntpd[3550]: kernel time sync status 0040
Mar 13 14:29:56 duke ntpd[3550]: frequency initialized 8.136 PPM from /var/lib/ntp/ntp.drift
Mar 13 14:29:56 duke kernel: Inspecting /boot/System.map-2.6.33
Mar 13 14:29:56 duke kernel: Inspecting /boot/System.map
Mar 13 14:29:56 duke kernel: Inspecting /usr/src/linux/System.map
Mar 13 14:29:56 duke kernel: Cannot find map file.
Mar 13 14:29:56 duke kernel: Loaded 43693 symbols from 76 modules.
Mar 13 14:29:56 duke kernel: fffffff] (base 0xe0000000)
Mar 13 14:29:56 duke kernel: PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
Mar 13 14:29:56 duke kernel: PCI: Using configuration type 1 for base access
Mar 13 14:29:56 duke kernel: bio: create slab <bio-0> at 0
Mar 13 14:29:56 duke kernel: ACPI: EC: Look up EC in DSDT
Mar 13 14:29:56 duke kernel: ACPI: Interpreter enabled
Mar 13 14:29:56 duke kernel: ACPI: (supports S0 S3 S4 S5)
Mar 13 14:29:56 duke kernel: ACPI: Using IOAPIC for interrupt routing
Mar 13 14:29:56 duke kernel: ACPI: No dock devices found.
Mar 13 14:29:56 duke kernel: ACPI: PCI Root Bridge [PCI0] (0000:00)
Mar 13 14:29:56 duke kernel: pci_root PNP0A08:00: ignoring host bridge windows from ACPI; boot with "pci=use_crs" to use them
Mar 13 14:29:56 duke kernel: pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7] (ignored)
Mar 13 14:29:56 duke kernel: pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff] (ignored)
Mar 13 14:29:56 duke kernel: pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
Mar 13 14:29:56 duke kernel: pci_root PNP0A08:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored)
Mar 13 14:29:56 duke kernel: pci_root PNP0A08:00: host bridge window [mem 0x7ff00000-0xfebfffff] (ignored)
Mar 13 14:29:56 duke kernel: pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
Mar 13 14:29:56 duke kernel: pci 0000:00:01.0: PME# disabled
Mar 13 14:29:56 duke kernel: pci 0000:00:1a.0: reg 20: [io 0xfc00-0xfc1f]
Mar 13 14:29:56 duke kernel: pci 0000:00:1a.1: reg 20: [io 0xf800-0xf81f]
Mar 13 14:29:56 duke kernel: pci 0000:00:1a.7: reg 10: [mem 0xfdfff000-0xfdfff3ff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
Mar 13 14:29:56 duke kernel: pci 0000:00:1a.7: PME# disabled
Mar 13 14:29:56 duke kernel: pci 0000:00:1b.0: reg 10: [mem 0xfdff4000-0xfdff7fff 64bit]
Mar 13 14:29:56 duke kernel: pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
Mar 13 14:29:56 duke kernel: pci 0000:00:1b.0: PME# disabled
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.0: PME# disabled
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.2: PME# disabled
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.3: PME# disabled
Mar 13 14:29:56 duke kernel: pci 0000:00:1d.0: reg 20: [io 0xf400-0xf41f]
Mar 13 14:29:56 duke kernel: pci 0000:00:1d.1: reg 20: [io 0xf000-0xf01f]
Mar 13 14:29:56 duke kernel: pci 0000:00:1d.2: reg 20: [io 0xec00-0xec1f]
Mar 13 14:29:56 duke kernel: pci 0000:00:1d.7: reg 10: [mem 0xfdffe000-0xfdffe3ff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
Mar 13 14:29:56 duke kernel: pci 0000:00:1d.7: PME# disabled
Mar 13 14:29:56 duke kernel: pci 0000:00:1f.0: quirk: [io 0x0400-0x047f] claimed by ICH6 ACPI/GPIO/TCO
Mar 13 14:29:56 duke kernel: pci 0000:00:1f.0: quirk: [io 0x0480-0x04bf] claimed by ICH6 GPIO
Mar 13 14:29:56 duke kernel: pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0800 (mask 003f)
Mar 13 14:29:56 duke kernel: pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 003f)
Mar 13 14:29:56 duke kernel: pci 0000:00:1f.2: reg 10: [io 0xe800-0xe807]
Mar 13 14:29:56 duke kernel: pci 0000:00:1f.2: reg 14: [io 0xe400-0xe403]
Mar 13 14:29:56 duke kernel: pci 0000:00:1f.2: reg 18: [io 0xe000-0xe007]
Mar 13 14:29:56 duke kernel: pci 0000:00:1f.2: reg 1c: [io 0xdc00-0xdc03]
Mar 13 14:29:56 duke kernel: pci 0000:00:1f.2: reg 20: [io 0xd800-0xd81f]
Mar 13 14:29:56 duke kernel: pci 0000:00:1f.2: reg 24: [mem 0xfdffd000-0xfdffd7ff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1f.2: PME# supported from D3hot
Mar 13 14:29:56 duke kernel: pci 0000:00:1f.2: PME# disabled
Mar 13 14:29:56 duke kernel: pci 0000:00:1f.3: reg 10: [mem 0xfdffc000-0xfdffc0ff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1f.3: reg 20: [io 0x0500-0x051f]
Mar 13 14:29:56 duke syslogd: /dev/console: Resource temporarily unavailable
Mar 13 14:29:56 duke kernel: pci 0000:00:1f.6: reg 10: [mem 0xfdffb000-0xfdffbfff 64bit]
Mar 13 14:29:56 duke kernel: pci 0000:01:00.0: reg 10: [mem 0xfb000000-0xfbffffff]
Mar 13 14:29:56 duke kernel: pci 0000:01:00.0: reg 14: [mem 0xb0000000-0xbfffffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci 0000:01:00.0: reg 1c: [mem 0xce000000-0xcfffffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci 0000:01:00.0: reg 24: [io 0x5c00-0x5c7f]
Mar 13 14:29:56 duke kernel: pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0007ffff pref]
Mar 13 14:29:56 duke kernel: pci 0000:01:00.1: reg 10: [mem 0xfcffc000-0xfcffffff]
Mar 13 14:29:56 duke kernel: pci 0000:00:01.0: PCI bridge to [bus 01-01]
Mar 13 14:29:56 duke kernel: pci 0000:00:01.0: bridge window [io 0x5000-0x5fff]
Mar 13 14:29:56 duke kernel: pci 0000:00:01.0: bridge window [mem 0xfb000000-0xfcffffff]
Mar 13 14:29:56 duke kernel: pci 0000:00:01.0: bridge window [mem 0xb0000000-0xcfffffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.0: PCI bridge to [bus 02-02]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.0: bridge window [io 0xa000-0xafff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.0: bridge window [mem 0xfdc00000-0xfdcfffff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.0: bridge window [mem 0xfdb00000-0xfdbfffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci 0000:03:00.0: reg 24: [mem 0xfdafe000-0xfdafffff]
Mar 13 14:29:56 duke kernel: pci 0000:03:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
Mar 13 14:29:56 duke kernel: pci 0000:03:00.0: PME# supported from D3hot
Mar 13 14:29:56 duke kernel: pci 0000:03:00.0: PME# disabled
Mar 13 14:29:56 duke kernel: pci 0000:03:00.1: reg 10: [io 0x9c00-0x9c07]
Mar 13 14:29:56 duke kernel: pci 0000:03:00.1: reg 14: [io 0x9800-0x9803]
Mar 13 14:29:56 duke kernel: pci 0000:03:00.1: reg 18: [io 0x9400-0x9407]
Mar 13 14:29:56 duke kernel: pci 0000:03:00.1: reg 1c: [io 0x9000-0x9003]
Mar 13 14:29:56 duke kernel: pci 0000:03:00.1: reg 20: [io 0x8c00-0x8c0f]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.2: PCI bridge to [bus 03-03]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.2: bridge window [io 0x8000-0x9fff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.2: bridge window [mem 0xfda00000-0xfdafffff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.2: bridge window [mem 0xfd900000-0xfd9fffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci 0000:04:00.0: reg 10: [mem 0xfdefc000-0xfdefffff 64bit]
Mar 13 14:29:56 duke kernel: pci 0000:04:00.0: reg 18: [io 0x6c00-0x6cff]
Mar 13 14:29:56 duke kernel: pci 0000:04:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
Mar 13 14:29:56 duke kernel: pci 0000:04:00.0: supports D1 D2
Mar 13 14:29:56 duke kernel: pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
Mar 13 14:29:56 duke kernel: pci 0000:04:00.0: PME# disabled
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.3: PCI bridge to [bus 04-04]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.3: bridge window [io 0x6000-0x6fff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.3: bridge window [mem 0xfde00000-0xfdefffff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.3: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci 0000:05:00.0: reg 10: [mem 0xdbfff000-0xdbfff7ff]
Mar 13 14:29:56 duke kernel: pci 0000:05:00.0: reg 14: [io 0x7c00-0x7c7f]
Mar 13 14:29:56 duke kernel: pci 0000:05:00.0: supports D2
Mar 13 14:29:56 duke kernel: pci 0000:05:00.0: PME# supported from D2 D3hot D3cold
Mar 13 14:29:56 duke kernel: pci 0000:05:00.0: PME# disabled
Mar 13 14:29:56 duke kernel: pci 0000:05:02.0: reg 10: [mem 0xf4000000-0xf7ffffff pref]
Mar 13 14:29:56 duke kernel: pci 0000:05:03.0: reg 10: [mem 0xd4000000-0xd7ffffff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1e.0: PCI bridge to [bus 05-05] (subtractive decode)
Mar 13 14:29:56 duke kernel: pci 0000:00:1e.0: bridge window [io 0x7000-0x7fff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1e.0: bridge window [mem 0xd4000000-0xdbffffff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1e.0: bridge window [mem 0xf4000000-0xf7ffffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci_bus 0000:00: on NUMA node 0
Mar 13 14:29:56 duke kernel: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
Mar 13 14:29:56 duke kernel: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
Mar 13 14:29:56 duke kernel: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
Mar 13 14:29:56 duke kernel: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
Mar 13 14:29:56 duke kernel: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
Mar 13 14:29:56 duke kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 5 9 10 11 12 *14 15)
Mar 13 14:29:56 duke kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 5 9 10 11 12 14 *15)
Mar 13 14:29:56 duke kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs 5 9 10 *11 12 14 15)
Mar 13 14:29:56 duke kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 5 9 *10 11 12 14 15)
Mar 13 14:29:56 duke kernel: ACPI: PCI Interrupt Link [LNKE] (IRQs 5 9 10 11 12 14 15) *0, disabled.
Mar 13 14:29:56 duke kernel: ACPI: PCI Interrupt Link [LNKF] (IRQs 5 *9 10 11 12 14 15)
Mar 13 14:29:56 duke kernel: ACPI: PCI Interrupt Link [LNK0] (IRQs *5 9 10 11 12 14 15)
Mar 13 14:29:56 duke kernel: ACPI: PCI Interrupt Link [LNK1] (IRQs 5 9 10 11 12 14 *15)
Mar 13 14:29:56 duke kernel: vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
Mar 13 14:29:56 duke kernel: vgaarb: loaded
Mar 13 14:29:56 duke kernel: SCSI subsystem initialized
Mar 13 14:29:56 duke kernel: libata version 3.00 loaded.
Mar 13 14:29:56 duke kernel: PCI: Using ACPI for IRQ routing
Mar 13 14:29:56 duke kernel: PCI: pci_cache_line_size set to 64 bytes
Mar 13 14:29:56 duke kernel: hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
Mar 13 14:29:56 duke kernel: hpet0: 3 comparators, 64-bit 14.318180 MHz counter
Mar 13 14:29:56 duke kernel: Switching to clocksource tsc
Mar 13 14:29:56 duke kernel: pnp: PnP ACPI init
Mar 13 14:29:56 duke kernel: ACPI: bus type pnp registered
Mar 13 14:29:56 duke kernel: pnp: PnP ACPI: found 14 devices
Mar 13 14:29:56 duke kernel: ACPI: ACPI bus type pnp unregistered
Mar 13 14:29:56 duke kernel: system 00:01: [io 0x04d0-0x04d1] has been reserved
Mar 13 14:29:56 duke kernel: system 00:01: [io 0x0290-0x029f] has been reserved
Mar 13 14:29:56 duke kernel: system 00:01: [io 0x0800-0x087f] has been reserved
Mar 13 14:29:56 duke kernel: system 00:01: [io 0x0880-0x088f] has been reserved
Mar 13 14:29:56 duke kernel: system 00:0a: [io 0x0400-0x04bf] could not be reserved
Mar 13 14:29:56 duke kernel: system 00:0c: [mem 0xe0000000-0xefffffff] has been reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0x000d6000-0x000d7fff] has been reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0x000f0000-0x000f7fff] could not be reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0x000f8000-0x000fbfff] could not be reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0x000fc000-0x000fffff] could not be reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0x7ff00000-0x7fffffff] could not be reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0xfed00000-0xfed000ff] has been reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0x7fee0000-0x7fefffff] could not be reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0x00000000-0x0009ffff] could not be reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0x00100000-0x7fedffff] could not be reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0xfec00000-0xfec00fff] could not be reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0xfed13000-0xfed1ffff] has been reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0xfed20000-0xfed9ffff] has been reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0xfee00000-0xfee00fff] has been reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0xffb00000-0xffb7ffff] has been reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0xfff00000-0xffffffff] has been reserved
Mar 13 14:29:56 duke kernel: system 00:0d: [mem 0x000e0000-0x000effff] has been reserved
Mar 13 14:29:56 duke kernel: pci 0000:01:00.0: BAR 6: assigned [mem 0xc0000000-0xc007ffff pref]
Mar 13 14:29:56 duke kernel: pci 0000:00:01.0: PCI bridge to [bus 01-01]
Mar 13 14:29:56 duke kernel: pci 0000:00:01.0: bridge window [io 0x5000-0x5fff]
Mar 13 14:29:56 duke kernel: pci 0000:00:01.0: bridge window [mem 0xfb000000-0xfcffffff]
Mar 13 14:29:56 duke kernel: pci 0000:00:01.0: bridge window [mem 0xb0000000-0xcfffffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.0: PCI bridge to [bus 02-02]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.0: bridge window [io 0xa000-0xafff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.0: bridge window [mem 0xfdc00000-0xfdcfffff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.0: bridge window [mem 0xfdb00000-0xfdbfffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci 0000:03:00.0: BAR 6: assigned [mem 0xfd900000-0xfd90ffff pref]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.2: PCI bridge to [bus 03-03]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.2: bridge window [io 0x8000-0x9fff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.2: bridge window [mem 0xfda00000-0xfdafffff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.2: bridge window [mem 0xfd900000-0xfd9fffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci 0000:04:00.0: BAR 6: assigned [mem 0xfdd00000-0xfdd1ffff pref]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.3: PCI bridge to [bus 04-04]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.3: bridge window [io 0x6000-0x6fff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.3: bridge window [mem 0xfde00000-0xfdefffff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.3: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci 0000:00:1e.0: PCI bridge to [bus 05-05]
Mar 13 14:29:56 duke kernel: pci 0000:00:1e.0: bridge window [io 0x7000-0x7fff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1e.0: bridge window [mem 0xd4000000-0xdbffffff]
Mar 13 14:29:56 duke kernel: pci 0000:00:1e.0: bridge window [mem 0xf4000000-0xf7ffffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Mar 13 14:29:56 duke kernel: pci 0000:00:01.0: setting latency timer to 64
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.0: setting latency timer to 64
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.2: setting latency timer to 64
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
Mar 13 14:29:56 duke kernel: pci 0000:00:1c.3: setting latency timer to 64
Mar 13 14:29:56 duke kernel: pci 0000:00:1e.0: setting latency timer to 64
Mar 13 14:29:56 duke kernel: pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
Mar 13 14:29:56 duke kernel: pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffffffffffff]
Mar 13 14:29:56 duke kernel: pci_bus 0000:01: resource 0 [io 0x5000-0x5fff]
Mar 13 14:29:56 duke kernel: pci_bus 0000:01: resource 1 [mem 0xfb000000-0xfcffffff]
Mar 13 14:29:56 duke kernel: pci_bus 0000:01: resource 2 [mem 0xb0000000-0xcfffffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci_bus 0000:02: resource 0 [io 0xa000-0xafff]
Mar 13 14:29:56 duke kernel: pci_bus 0000:02: resource 1 [mem 0xfdc00000-0xfdcfffff]
Mar 13 14:29:56 duke kernel: pci_bus 0000:02: resource 2 [mem 0xfdb00000-0xfdbfffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci_bus 0000:03: resource 0 [io 0x8000-0x9fff]
Mar 13 14:29:56 duke kernel: pci_bus 0000:03: resource 1 [mem 0xfda00000-0xfdafffff]
Mar 13 14:29:56 duke kernel: pci_bus 0000:03: resource 2 [mem 0xfd900000-0xfd9fffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci_bus 0000:04: resource 0 [io 0x6000-0x6fff]
Mar 13 14:29:56 duke kernel: pci_bus 0000:04: resource 1 [mem 0xfde00000-0xfdefffff]
Mar 13 14:29:56 duke kernel: pci_bus 0000:04: resource 2 [mem 0xfdd00000-0xfddfffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci_bus 0000:05: resource 0 [io 0x7000-0x7fff]
Mar 13 14:29:56 duke kernel: pci_bus 0000:05: resource 1 [mem 0xd4000000-0xdbffffff]
Mar 13 14:29:56 duke kernel: pci_bus 0000:05: resource 2 [mem 0xf4000000-0xf7ffffff 64bit pref]
Mar 13 14:29:56 duke kernel: pci_bus 0000:05: resource 3 [io 0x0000-0xffff]
Mar 13 14:29:56 duke kernel: pci_bus 0000:05: resource 4 [mem 0x00000000-0xffffffffffffffff]
Mar 13 14:29:56 duke kernel: NET: Registered protocol family 2
Mar 13 14:29:56 duke kernel: IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
Mar 13 14:29:56 duke kernel: TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
Mar 13 14:29:56 duke kernel: TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
Mar 13 14:29:56 duke kernel: TCP: Hash tables configured (established 262144 bind 65536)
Mar 13 14:29:56 duke kernel: TCP reno registered
Mar 13 14:29:56 duke kernel: UDP hash table entries: 1024 (order: 3, 32768 bytes)
Mar 13 14:29:56 duke kernel: UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
Mar 13 14:29:56 duke kernel: NET: Registered protocol family 1
Mar 13 14:29:56 duke kernel: pci 0000:01:00.0: Boot video device
Mar 13 14:29:56 duke kernel: PCI: CLS 64 bytes, default 64
Mar 13 14:29:56 duke kernel: Scanning for low memory corruption every 60 seconds
Mar 13 14:29:56 duke kernel: HugeTLB registered 2 MB page size, pre-allocated 0 pages
Mar 13 14:29:56 duke kernel: SGI XFS with security attributes, realtime, large block/inode numbers, no debug enabled
Mar 13 14:29:56 duke kernel: msgmni has been set to 4019
Mar 13 14:29:56 duke kernel: alg: No test for stdrng (krng)
Mar 13 14:29:56 duke kernel: Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
Mar 13 14:29:56 duke kernel: io scheduler noop registered
Mar 13 14:29:56 duke kernel: io scheduler cfq registered (default)
Mar 13 14:29:56 duke kernel: pcieport 0000:00:01.0: setting latency timer to 64
Mar 13 14:29:56 duke kernel: pcieport 0000:00:1c.0: setting latency timer to 64
Mar 13 14:29:56 duke kernel: pcieport 0000:00:1c.2: setting latency timer to 64
Mar 13 14:29:56 duke kernel: pcieport 0000:00:1c.3: setting latency timer to 64
Mar 13 14:29:56 duke kernel: lp: driver loaded but no devices found
Mar 13 14:29:56 duke kernel: Generic RTC Driver v1.07
Mar 13 14:29:56 duke kernel: Non-volatile memory driver v1.3
Mar 13 14:29:56 duke kernel: Linux agpgart interface v0.103
Mar 13 14:29:56 duke kernel: [drm] Initialized drm 1.1.0 20060810
Mar 13 14:29:56 duke kernel: Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
Mar 13 14:29:56 duke kernel: serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Mar 13 14:29:56 duke kernel: 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Mar 13 14:29:56 duke kernel: parport_pc 00:08: reported by Plug and Play ACPI
Mar 13 14:29:56 duke kernel: parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
Mar 13 14:29:56 duke kernel: lp0: using parport0 (interrupt-driven).
Mar 13 14:29:56 duke kernel: loop: module loaded
Mar 13 14:29:56 duke kernel: ahci 0000:00:1f.2: version 3.0
Mar 13 14:29:56 duke kernel: ahci 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
Mar 13 14:29:56 duke kernel: ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x33 impl SATA mode
Mar 13 14:29:56 duke kernel: ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pio slum part ccc ems
Mar 13 14:29:56 duke kernel: ahci 0000:00:1f.2: setting latency timer to 64
Mar 13 14:29:56 duke kernel: scsi0 : ahci
Mar 13 14:29:56 duke kernel: scsi1 : ahci
Mar 13 14:29:56 duke kernel: scsi2 : ahci
Mar 13 14:29:56 duke kernel: scsi3 : ahci
Mar 13 14:29:56 duke kernel: scsi4 : ahci
Mar 13 14:29:56 duke kernel: scsi5 : ahci
Mar 13 14:29:56 duke kernel: ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 17
Mar 13 14:29:56 duke kernel: ata2: SATA max UDMA/133 abar m2048@0xfdffd000 port 0xfdffd180 irq 17
Mar 13 14:29:56 duke kernel: ata3: DUMMY
Mar 13 14:29:56 duke kernel: ata4: DUMMY
Mar 13 14:29:56 duke kernel: ata5: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 17
Mar 13 14:29:56 duke kernel: ata6: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 17
Mar 13 14:29:56 duke kernel: ahci 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
Mar 13 14:29:56 duke kernel: ahci 0000:03:00.0: JMB361 has only one port, port_map 0x3 -> 0x1
Mar 13 14:29:56 duke kernel: ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x1 impl SATA mode
Mar 13 14:29:56 duke kernel: ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part
Mar 13 14:29:56 duke kernel: ahci 0000:03:00.0: setting latency timer to 64
Mar 13 14:29:56 duke kernel: scsi6 : ahci
Mar 13 14:29:56 duke kernel: scsi7 : ahci
Mar 13 14:29:56 duke kernel: ata7: SATA max UDMA/133 abar m8192@0xfdafe000 port 0xfdafe100 irq 18
Mar 13 14:29:56 duke kernel: ata8: DUMMY
Mar 13 14:29:56 duke kernel: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
Mar 13 14:29:56 duke kernel: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
Mar 13 14:29:56 duke kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
Mar 13 14:29:56 duke kernel: mice: PS/2 mouse device common for all mice
Mar 13 14:29:56 duke kernel: md: raid0 personality registered for level 0
Mar 13 14:29:56 duke kernel: cpuidle: using governor ladder
Mar 13 14:29:56 duke kernel: ioatdma: Intel(R) QuickData Technology Driver 4.00
Mar 13 14:29:56 duke kernel: TCP cubic registered
Mar 13 14:29:56 duke kernel: NET: Registered protocol family 17
Mar 13 14:29:56 duke kernel: ata7: SATA link down (SStatus 0 SControl 300)
Mar 13 14:29:56 duke kernel: ata2: SATA link down (SStatus 0 SControl 300)
Mar 13 14:29:56 duke kernel: ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Mar 13 14:29:56 duke kernel: ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 13 14:29:56 duke kernel: ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 13 14:29:56 duke kernel: ata1.00: ATA-8: OCZ-VERTEX, 1.5, max UDMA/133
Mar 13 14:29:56 duke kernel: ata1.00: 125045424 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
Mar 13 14:29:56 duke kernel: ata1.00: configured for UDMA/133
Mar 13 14:29:56 duke kernel: scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX 1.5 PQ: 0 ANSI: 5
Mar 13 14:29:56 duke kernel: sd 0:0:0:0: [sda] 125045424 512-byte logical blocks: (64.0 GB/59.6 GiB)
Mar 13 14:29:56 duke kernel: sd 0:0:0:0: [sda] Write Protect is off
Mar 13 14:29:56 duke kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Mar 13 14:29:56 duke kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 13 14:29:56 duke kernel: sda: sda1 sda2
Mar 13 14:29:56 duke kernel: ata5.00: ATA-8: WDC WD15EARS-00Z5B1, 80.00A80, max UDMA/133
Mar 13 14:29:56 duke kernel: ata6.00: ATAPI: PIONEER DVD-RW DVR-212D, 1.21, max UDMA/66
Mar 13 14:29:56 duke kernel: ata5.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
Mar 13 14:29:56 duke kernel: sd 0:0:0:0: [sda] Attached SCSI disk
Mar 13 14:29:56 duke kernel: ata5.00: configured for UDMA/133
Mar 13 14:29:56 duke kernel: scsi 4:0:0:0: Direct-Access ATA WDC WD15EARS-00Z 80.0 PQ: 0 ANSI: 5
Mar 13 14:29:56 duke kernel: sd 4:0:0:0: [sdb] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
Mar 13 14:29:56 duke kernel: sd 4:0:0:0: [sdb] Write Protect is off
Mar 13 14:29:56 duke kernel: sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Mar 13 14:29:56 duke kernel: sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Mar 13 14:29:56 duke kernel: sdb: sdb1
Mar 13 14:29:56 duke kernel: sd 4:0:0:0: [sdb] Attached SCSI disk
Mar 13 14:29:56 duke kernel: ata6.00: configured for UDMA/66
Mar 13 14:29:56 duke kernel: scsi 5:0:0:0: CD-ROM PIONEER DVD-RW DVR-212D 1.21 PQ: 0 ANSI: 5
Mar 13 14:29:56 duke kernel: sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Mar 13 14:29:56 duke kernel: Uniform CD-ROM driver Revision: 3.20
Mar 13 14:29:56 duke kernel: sr 5:0:0:0: Attached scsi CD-ROM sr0
Mar 13 14:29:56 duke kernel: md: Waiting for all devices to be available before autodetect
Mar 13 14:29:56 duke kernel: md: If you don't use raid, use raid=noautodetect
Mar 13 14:29:56 duke kernel: md: Autodetecting RAID arrays.
Mar 13 14:29:56 duke kernel: md: Scanned 0 and added 0 devices.
Mar 13 14:29:56 duke kernel: md: autorun ...
Mar 13 14:29:56 duke kernel: md: ... autorun DONE.
Mar 13 14:29:56 duke kernel: EXT3-fs (sda2): error: couldn't mount because of unsupported optional features (240)
Mar 13 14:29:56 duke kernel: EXT4-fs (sda2): mounted filesystem with ordered data mode
Mar 13 14:29:56 duke kernel: VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
Mar 13 14:29:56 duke kernel: Freeing unused kernel memory: 408k freed
Mar 13 14:29:56 duke kernel: fuse init (API version 7.13)
Mar 13 14:29:56 duke kernel: HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
Mar 13 14:29:56 duke kernel: HDA Intel 0000:00:1b.0: setting latency timer to 64
Mar 13 14:29:56 duke kernel: hda_codec: ALC883: BIOS auto-probing.
Mar 13 14:29:56 duke kernel: HDA Intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
Mar 13 14:29:56 duke kernel: HDA Intel 0000:01:00.1: setting latency timer to 64
Mar 13 14:29:56 duke kernel: Linux video capture interface: v2.00
Mar 13 14:29:56 duke kernel: ivtv: Start initialization, version 1.4.1
Mar 13 14:29:56 duke kernel: ivtv0: Initializing card 0
Mar 13 14:29:56 duke kernel: ivtv0: Autodetected Hauppauge card (cx23416 based)
Mar 13 14:29:56 duke kernel: ivtv 0000:05:02.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
Mar 13 14:29:56 duke kernel: tveeprom 0-0050: Hauppauge model 32062, rev B185, serial# 2842715
Mar 13 14:29:56 duke kernel: tveeprom 0-0050: tuner model is TCL 2002N 6A (idx 85, type 50)
Mar 13 14:29:56 duke kernel: tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
Mar 13 14:29:56 duke kernel: tveeprom 0-0050: audio processor is MSP3445 (idx 12)
Mar 13 14:29:56 duke kernel: tveeprom 0-0050: decoder processor is SAA7115 (idx 19)
Mar 13 14:29:56 duke kernel: tveeprom 0-0050: has no radio, has IR receiver, has no IR transmitter
Mar 13 14:29:56 duke kernel: ivtv0: Autodetected Hauppauge WinTV PVR-250
Mar 13 14:29:56 duke kernel: saa7115 0-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv i2c driver #0)
Mar 13 14:29:56 duke kernel: msp3400 0-0040: MSP3445G-B8 found @ 0x80 (ivtv i2c driver #0)
Mar 13 14:29:56 duke kernel: msp3400 0-0040: msp3400 supports radio, mode is autodetect and autoselect
Mar 13 14:29:56 duke kernel: tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
Mar 13 14:29:56 duke kernel: tuner-simple 0-0061: creating new instance
Mar 13 14:29:56 duke kernel: tuner-simple 0-0061: type set to 50 (TCL 2002N)
Mar 13 14:29:56 duke kernel: IRQ 17/ivtv0: IRQF_DISABLED is not guaranteed on shared IRQs
Mar 13 14:29:56 duke kernel: ivtv0: Registered device video0 for encoder MPG (4096 kB)
Mar 13 14:29:56 duke kernel: ivtv0: Registered device video32 for encoder YUV (2048 kB)
Mar 13 14:29:56 duke kernel: ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
Mar 13 14:29:56 duke kernel: ivtv0: Registered device video24 for encoder PCM (320 kB)
Mar 13 14:29:56 duke kernel: ivtv0: Initialized card: Hauppauge WinTV PVR-250
Mar 13 14:29:56 duke kernel: ivtv: End initialization
Mar 13 14:29:56 duke kernel: ACPI: Invalid PBLK length [0]
Mar 13 14:29:56 duke kernel: ACPI Error (psparse-0537): Method parse/execution failed
Mar 13 14:29:56 duke kernel: input: Power Button as /class/input/input0
Mar 13 14:29:56 duke kernel: ACPI: Power Button [PWRB]
Mar 13 14:29:56 duke kernel: usbcore: registered new interface driver usbfs
Mar 13 14:29:56 duke kernel: [\_PR_.CPU0._PDC] (Node ffff88007f858490)
Mar 13 14:29:56 duke kernel: usbcore: registered new interface driver hub
Mar 13 14:29:56 duke kernel: , AE_ALREADY_EXISTS
Mar 13 14:29:56 duke kernel: ACPI: Marking method _PDC as Serialized because of AE_ALREADY_EXISTS error
Mar 13 14:29:56 duke kernel: pata_jmicron 0000:03:00.1: enabling device (0000 -> 0001)
Mar 13 14:29:56 duke kernel: usbcore: registered new device driver usb
Mar 13 14:29:56 duke kernel: pata_jmicron 0000:03:00.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
Mar 13 14:29:56 duke kernel:
Mar 13 14:29:56 duke kernel: thermal LNXTHERM:01: registered as thermal_zone0
Mar 13 14:29:56 duke kernel: input: Power Button as /class/input/input1
Mar 13 14:29:56 duke kernel: ACPI: Power Button [PWRF]
Mar 13 14:29:56 duke kernel: ACPI: Thermal Zone [THRM] (36 C)
Mar 13 14:29:56 duke kernel: ACPI: Invalid PBLK length [0]
Mar 13 14:29:56 duke kernel: pata_jmicron 0000:03:00.1: setting latency timer to 64
Mar 13 14:29:56 duke kernel: ACPI: SSDT 000000007fee8750 000CE (v01 PmRef Cpu1Ist 00003000 INTL 20041203)
Mar 13 14:29:56 duke kernel: scsi8 : pata_jmicron
Mar 13 14:29:56 duke kernel: scsi9 : pata_jmicron
Mar 13 14:29:56 duke kernel: ata9: PATA max UDMA/100 cmd 0x9c00 ctl 0x9800 bmdma 0x8c00 irq 19
Mar 13 14:29:56 duke kernel: ata10: PATA max UDMA/100 cmd 0x9400 ctl 0x9000 bmdma 0x8c08 irq 19
Mar 13 14:29:56 duke kernel:
Mar 13 14:29:56 duke kernel: nvidia: module license 'NVIDIA' taints kernel.
Mar 13 14:29:56 duke kernel: firewire_ohci 0000:05:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
Mar 13 14:29:56 duke kernel: firewire_ohci 0000:05:00.0: setting latency timer to 64
Mar 13 14:29:56 duke kernel: uhci_hcd: USB Universal Host Controller Interface driver
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Mar 13 14:29:56 duke kernel: sky2 driver version 1.26
Mar 13 14:29:56 duke kernel: sky2 0000:04:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
Mar 13 14:29:56 duke kernel: sky2 0000:04:00.0: setting latency timer to 64
Mar 13 14:29:56 duke kernel: sky2 0000:04:00.0: Yukon-2 EC Ultra chip revision 2
Mar 13 14:29:56 duke kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Mar 13 14:29:56 duke kernel: sd 4:0:0:0: Attached scsi generic sg1 type 0
Mar 13 14:29:56 duke kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Mar 13 14:29:56 duke kernel: Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
Mar 13 14:29:56 duke kernel: cx18: Start initialization, version 1.4.0
Mar 13 14:29:56 duke kernel: sr 5:0:0:0: Attached scsi generic sg2 type 5
Mar 13 14:29:56 duke kernel: firewire_ohci: Added fw-ohci device 0000:05:00.0, OHCI version 1.10
Mar 13 14:29:56 duke kernel: cx18-0: Initializing card 0
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1a.0: setting latency timer to 64
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1a.0: UHCI Host Controller
Mar 13 14:29:56 duke kernel: cx18-0: Autodetected Hauppauge card
Mar 13 14:29:56 duke kernel: sky2 eth0: addr 00:15:58:8a:ae:e5
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000fc00
Mar 13 14:29:56 duke kernel: ACPI: Fan [FAN] (on)
Mar 13 14:29:56 duke kernel: cx18 0000:05:03.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
Mar 13 14:29:56 duke kernel: cx18-0: Unreasonably low latency timer, setting to 64 (was 2)
Mar 13 14:29:56 duke kernel: usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
Mar 13 14:29:56 duke kernel: cx18-0: cx23418 revision 01010000 (B)
Mar 13 14:29:56 duke kernel: usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Mar 13 14:29:56 duke kernel: usb usb1: Product: UHCI Host Controller
Mar 13 14:29:56 duke kernel: usb usb1: Manufacturer: Linux 2.6.33 uhci_hcd
Mar 13 14:29:56 duke kernel: usb usb1: SerialNumber: 0000:00:1a.0
Mar 13 14:29:56 duke kernel: hub 1-0:1.0: USB hub found
Mar 13 14:29:56 duke kernel: hub 1-0:1.0: 2 ports detected
Mar 13 14:29:56 duke kernel: ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
Mar 13 14:29:56 duke kernel: ehci_hcd 0000:00:1a.7: setting latency timer to 64
Mar 13 14:29:56 duke kernel: ehci_hcd 0000:00:1a.7: EHCI Host Controller
Mar 13 14:29:56 duke kernel: ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 2
Mar 13 14:29:56 duke kernel: ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
Mar 13 14:29:56 duke kernel: ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfdfff000
Mar 13 14:29:56 duke kernel: ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
Mar 13 14:29:56 duke kernel: usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
Mar 13 14:29:56 duke kernel: usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Mar 13 14:29:56 duke kernel: usb usb2: Product: EHCI Host Controller
Mar 13 14:29:56 duke kernel: usb usb2: Manufacturer: Linux 2.6.33 ehci_hcd
Mar 13 14:29:56 duke kernel: usb usb2: SerialNumber: 0000:00:1a.7
Mar 13 14:29:56 duke kernel: hub 2-0:1.0: USB hub found
Mar 13 14:29:56 duke kernel: hub 2-0:1.0: 4 ports detected
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1a.1: setting latency timer to 64
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1a.1: UHCI Host Controller
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 3
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000f800
Mar 13 14:29:56 duke kernel: usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
Mar 13 14:29:56 duke kernel: usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Mar 13 14:29:56 duke kernel: nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Mar 13 14:29:56 duke kernel: usb usb3: Product: UHCI Host Controller
Mar 13 14:29:56 duke kernel: usb usb3: Manufacturer: Linux 2.6.33 uhci_hcd
Mar 13 14:29:56 duke kernel: usb usb3: SerialNumber: 0000:00:1a.1
Mar 13 14:29:56 duke kernel: hub 3-0:1.0: USB hub found
Mar 13 14:29:56 duke kernel: hub 3-0:1.0: 2 ports detected
Mar 13 14:29:56 duke kernel: ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
Mar 13 14:29:56 duke kernel: ehci_hcd 0000:00:1d.7: setting latency timer to 64
Mar 13 14:29:56 duke kernel: ehci_hcd 0000:00:1d.7: EHCI Host Controller
Mar 13 14:29:56 duke kernel: ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
Mar 13 14:29:56 duke kernel: ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
Mar 13 14:29:56 duke kernel: ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdffe000
Mar 13 14:29:56 duke kernel: ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
Mar 13 14:29:56 duke kernel: usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
Mar 13 14:29:56 duke kernel: usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Mar 13 14:29:56 duke kernel: usb usb4: Product: EHCI Host Controller
Mar 13 14:29:56 duke kernel: usb usb4: Manufacturer: Linux 2.6.33 ehci_hcd
Mar 13 14:29:56 duke kernel: usb usb4: SerialNumber: 0000:00:1d.7
Mar 13 14:29:56 duke kernel: hub 4-0:1.0: USB hub found
Mar 13 14:29:56 duke kernel: hub 4-0:1.0: 6 ports detected
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1d.0: setting latency timer to 64
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1d.0: UHCI Host Controller
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000f400
Mar 13 14:29:56 duke kernel: usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
Mar 13 14:29:56 duke kernel: usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Mar 13 14:29:56 duke kernel: usb usb5: Product: UHCI Host Controller
Mar 13 14:29:56 duke kernel: usb usb5: Manufacturer: Linux 2.6.33 uhci_hcd
Mar 13 14:29:56 duke kernel: usb usb5: SerialNumber: 0000:00:1d.0
Mar 13 14:29:56 duke kernel: hub 5-0:1.0: USB hub found
Mar 13 14:29:56 duke kernel: hub 5-0:1.0: 2 ports detected
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1d.1: setting latency timer to 64
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1d.1: UHCI Host Controller
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000f000
Mar 13 14:29:56 duke kernel: usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
Mar 13 14:29:56 duke kernel: usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Mar 13 14:29:56 duke kernel: usb usb6: Product: UHCI Host Controller
Mar 13 14:29:56 duke kernel: usb usb6: Manufacturer: Linux 2.6.33 uhci_hcd
Mar 13 14:29:56 duke kernel: usb usb6: SerialNumber: 0000:00:1d.1
Mar 13 14:29:56 duke kernel: hub 6-0:1.0: USB hub found
Mar 13 14:29:56 duke kernel: hub 6-0:1.0: 2 ports detected
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1d.2: setting latency timer to 64
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1d.2: UHCI Host Controller
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
Mar 13 14:29:56 duke kernel: uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ec00
Mar 13 14:29:56 duke kernel: usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
Mar 13 14:29:56 duke kernel: usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Mar 13 14:29:56 duke kernel: usb usb7: Product: UHCI Host Controller
Mar 13 14:29:56 duke kernel: usb usb7: Manufacturer: Linux 2.6.33 uhci_hcd
Mar 13 14:29:56 duke kernel: usb usb7: SerialNumber: 0000:00:1d.2
Mar 13 14:29:56 duke kernel: hub 7-0:1.0: USB hub found
Mar 13 14:29:56 duke kernel: hub 7-0:1.0: 2 ports detected
Mar 13 14:29:56 duke kernel: tveeprom 1-0050: Hauppauge model 74551, rev C1A3, serial# 1752579
Mar 13 14:29:56 duke kernel: tveeprom 1-0050: MAC address is 00:0d:fe:1a:be:03
Mar 13 14:29:56 duke kernel: tveeprom 1-0050: tuner model is TCL MFNM05-4 (idx 103, type 43)
Mar 13 14:29:56 duke kernel: tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
Mar 13 14:29:56 duke kernel: tveeprom 1-0050: audio processor is CX23418 (idx 38)
Mar 13 14:29:56 duke kernel: tveeprom 1-0050: decoder processor is CX23418 (idx 31)
Mar 13 14:29:56 duke kernel: tveeprom 1-0050: has radio
Mar 13 14:29:56 duke kernel: cx18-0: Autodetected Hauppauge HVR-1600
Mar 13 14:29:56 duke kernel: cx18-0: Simultaneous Digital and Analog TV capture supported
Mar 13 14:29:56 duke kernel: IRQ 18/cx18-0: IRQF_DISABLED is not guaranteed on shared IRQs
Mar 13 14:29:56 duke kernel: firewire_core: created device fw0: GUID 00016c200022ce9e, S400
Mar 13 14:29:56 duke kernel: tuner 2-0043: chip found @ 0x86 (cx18 i2c driver #0-1)
Mar 13 14:29:56 duke kernel: tda9887 2-0043: creating new instance
Mar 13 14:29:56 duke kernel: tda9887 2-0043: tda988[5/6/7] found
Mar 13 14:29:56 duke kernel: tuner 2-0061: chip found @ 0xc2 (cx18 i2c driver #0-1)
Mar 13 14:29:56 duke kernel: cs5345 1-004c: chip found @ 0x98 (cx18 i2c driver #0-0)
Mar 13 14:29:56 duke kernel: tuner-simple 2-0061: creating new instance
Mar 13 14:29:56 duke kernel: tuner-simple 2-0061: type set to 43 (Philips NTSC MK3 (FM1236MK3 or FM1236/F))
Mar 13 14:29:56 duke kernel: cx18-0: Registered device video1 for encoder MPEG (64 x 32.00 kB)
Mar 13 14:29:56 duke kernel: DVB: registering new adapter (cx18)
Mar 13 14:29:56 duke kernel: nvidia 0000:01:00.0: setting latency timer to 64
Mar 13 14:29:56 duke kernel: vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
Mar 13 14:29:56 duke kernel: NVRM: loading NVIDIA UNIX x86_64 Kernel Module 195.36.08 Thu Feb 25 04:10:13 PST 2010
Mar 13 14:29:56 duke kernel: MXL5005S: Attached at address 0x63
Mar 13 14:29:56 duke kernel: DVB: registering adapter 0 frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)...
Mar 13 14:29:56 duke kernel: cx18-0: DVB Frontend registered
Mar 13 14:29:56 duke kernel: cx18-0: Registered DVB adapter0 for TS (32 x 32.00 kB)
Mar 13 14:29:56 duke kernel: cx18-0: Registered device video33 for encoder YUV (20 x 101.25 kB)
Mar 13 14:29:56 duke kernel: cx18-0: Registered device vbi1 for encoder VBI (20 x 51984 bytes)
Mar 13 14:29:56 duke kernel: cx18-0: Registered device video25 for encoder PCM audio (256 x 4.00 kB)
Mar 13 14:29:56 duke kernel: cx18-0: Registered device radio1 for encoder radio
Mar 13 14:29:56 duke kernel: cx18-0: Initialized card: Hauppauge HVR-1600
Mar 13 14:29:56 duke kernel: cx18: End initialization
Mar 13 14:29:56 duke kernel: cx18-alsa: module loading...
Mar 13 14:29:56 duke kernel: usb 3-2: new low speed USB device using uhci_hcd and address 2
Mar 13 14:29:56 duke kernel: usb 3-2: New USB device found, idVendor=15c2, idProduct=ffdc
Mar 13 14:29:56 duke kernel: usb 3-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Mar 13 14:29:56 duke kernel: usb 4-6: new high speed USB device using ehci_hcd and address 3
Mar 13 14:29:56 duke kernel: usb 4-6: New USB device found, idVendor=0b95, idProduct=7720
Mar 13 14:29:56 duke kernel: usb 4-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Mar 13 14:29:56 duke kernel: usb 4-6: Product: AX88772
Mar 13 14:29:56 duke kernel: usb 4-6: Manufacturer: ASIX Elec. Corp.
Mar 13 14:29:56 duke kernel: usb 4-6: SerialNumber: 000001
Mar 13 14:29:56 duke kernel: usb 5-2: new full speed USB device using uhci_hcd and address 2
Mar 13 14:29:56 duke kernel: usb 5-2: New USB device found, idVendor=0403, idProduct=6001
Mar 13 14:29:56 duke kernel: usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Mar 13 14:29:56 duke kernel: usb 5-2: Product: Triple Relay Controller
Mar 13 14:29:56 duke kernel: usb 5-2: Manufacturer: RTR
Mar 13 14:29:56 duke kernel: usb 5-2: SerialNumber: A4SI153I
Mar 13 14:29:56 duke kernel: usb 1-1: new low speed USB device using uhci_hcd and address 2
Mar 13 14:29:56 duke kernel: eth1: register 'asix' at usb-0000:00:1d.7-6, ASIX AX88772 USB 2.0 Ethernet, 00:50:5b:04:a2:4b
Mar 13 14:29:56 duke kernel: usbcore: registered new interface driver asix
Mar 13 14:29:56 duke kernel: usb 1-1: New USB device found, idVendor=046d, idProduct=c51e
Mar 13 14:29:56 duke kernel: usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Mar 13 14:29:56 duke kernel: usbcore: registered new interface driver hiddev
Mar 13 14:29:56 duke kernel: input: HID 046d:c51e as /class/input/input2
Mar 13 14:29:56 duke kernel: generic-usb 0003:046D:C51E.0001: input: USB HID v1.11 Keyboard [HID 046d:c51e] on usb-0000:00:1a.0-1/input0
Mar 13 14:29:56 duke kernel: input: HID 046d:c51e as /class/input/input3
Mar 13 14:29:56 duke kernel: generic-usb 0003:046D:C51E.0002: input,hiddev0: USB HID v1.11 Mouse [HID 046d:c51e] on usb-0000:00:1a.0-1/input1
Mar 13 14:29:56 duke kernel: usbcore: registered new interface driver usbhid
Mar 13 14:29:56 duke kernel: usbhid: USB HID core driver
Mar 13 14:29:56 duke kernel: usb 2-3: new high speed USB device using ehci_hcd and address 4
Mar 13 14:29:56 duke kernel: usb 2-3: New USB device found, idVendor=05e3, idProduct=0608
Mar 13 14:29:56 duke kernel: usb 2-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
Mar 13 14:29:56 duke kernel: usb 2-3: Product: USB2.0 Hub
Mar 13 14:29:56 duke kernel: hub 2-3:1.0: USB hub found
Mar 13 14:29:56 duke kernel: hub 2-3:1.0: 4 ports detected
Mar 13 14:29:56 duke kernel: usb 2-3.1: new full speed USB device using ehci_hcd and address 5
Mar 13 14:29:56 duke kernel: usb 2-3.1: New USB device found, idVendor=0c76, idProduct=1607
Mar 13 14:29:56 duke kernel: usb 2-3.1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
Mar 13 14:29:56 duke kernel: usb 2-3.1: Product: USB Headphone Set
Mar 13 14:29:56 duke kernel: input: USB Headphone Set as /class/input/input4
Mar 13 14:29:56 duke kernel: generic-usb 0003:0C76:1607.0003: input: USB HID v1.00 Device [USB Headphone Set] on usb-0000:00:1a.7-3.1/input3
Mar 13 14:29:56 duke kernel: usbcore: registered new interface driver snd-usb-audio
Mar 13 14:29:56 duke kernel: usb 2-3.2: new high speed USB device using ehci_hcd and address 6
Mar 13 14:29:56 duke kernel: usb 2-3.2: New USB device found, idVendor=2040, idProduct=7200
Mar 13 14:29:56 duke kernel: usb 2-3.2: New USB device strings: Mfr=1, Product=2, SerialNumber=10
Mar 13 14:29:56 duke kernel: usb 2-3.2: Product: WinTV HVR-950
Mar 13 14:29:56 duke kernel: usb 2-3.2: Manufacturer: Hauppauge
Mar 13 14:29:56 duke kernel: usb 2-3.2: SerialNumber: 4031688744
Mar 13 14:29:56 duke kernel: au0828 driver loaded
Mar 13 14:29:56 duke kernel: usb 2-3.3: new full speed USB device using ehci_hcd and address 7
Mar 13 14:29:56 duke kernel: usb 2-3.3: New USB device found, idVendor=0403, idProduct=6001
Mar 13 14:29:56 duke kernel: usb 2-3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Mar 13 14:29:56 duke kernel: usb 2-3.3: Product: Frankenswitch v3 4x4:1 matrix
Mar 13 14:29:56 duke kernel: usb 2-3.3: Manufacturer: RTR
Mar 13 14:29:56 duke kernel: usb 2-3.3: SerialNumber: A8S59W9K
Mar 13 14:29:56 duke kernel: usb 2-3.4: new low speed USB device using ehci_hcd and address 8
Mar 13 14:29:56 duke kernel: au0828: i2c bus registered
Mar 13 14:29:56 duke kernel: usb 2-3.4: New USB device found, idVendor=051d, idProduct=0002
Mar 13 14:29:56 duke kernel: usb 2-3.4: New USB device strings: Mfr=3, Product=1, SerialNumber=2
Mar 13 14:29:56 duke kernel: usb 2-3.4: Product: Back-UPS XS 1300 LCD FW:836.H8 .D USB FW:H8
Mar 13 14:29:56 duke kernel: usb 2-3.4: Manufacturer: American Power Conversion
Mar 13 14:29:56 duke kernel: usb 2-3.4: SerialNumber: BB0820009163
Mar 13 14:29:56 duke kernel: tveeprom 3-0050: Hauppauge model 72001, rev B3F0, serial# 5156904
Mar 13 14:29:56 duke kernel: tveeprom 3-0050: MAC address is 00:0d:fe:4e:b0:28
Mar 13 14:29:56 duke kernel: tveeprom 3-0050: tuner model is Xceive XC5000 (idx 150, type 76)
Mar 13 14:29:56 duke kernel: tveeprom 3-0050: TV standards NTSC(M) ATSC/DVB Digital (eeprom 0x88)
Mar 13 14:29:56 duke kernel: tveeprom 3-0050: audio processor is AU8522 (idx 44)
Mar 13 14:29:56 duke kernel: tveeprom 3-0050: decoder processor is AU8522 (idx 42)
Mar 13 14:29:56 duke kernel: tveeprom 3-0050: has no radio, has IR receiver, has no IR transmitter
Mar 13 14:29:56 duke kernel: hauppauge_eeprom: hauppauge eeprom: model=72001
Mar 13 14:29:56 duke kernel: au8522 3-0047: creating new instance
Mar 13 14:29:56 duke kernel: au8522_decoder creating new instance...
Mar 13 14:29:56 duke kernel: tuner 3-0061: chip found @ 0xc2 (au0828)
Mar 13 14:29:56 duke kernel: xc5000 3-0061: creating new instance
Mar 13 14:29:56 duke kernel: xc5000: Successfully identified at address 0x61
Mar 13 14:29:56 duke kernel: xc5000: Firmware has not been loaded previously
Mar 13 14:29:56 duke kernel: au8522 3-0047: attaching existing instance
Mar 13 14:29:56 duke kernel: xc5000 3-0061: attaching existing instance
Mar 13 14:29:56 duke kernel: xc5000: Successfully identified at address 0x61
Mar 13 14:29:56 duke kernel: xc5000: Firmware has not been loaded previously
Mar 13 14:29:56 duke kernel: DVB: registering new adapter (au0828)
Mar 13 14:29:56 duke kernel: DVB: registering adapter 1 frontend 0 (Auvitek AU8522 QAM/8VSB Frontend)...
Mar 13 14:29:56 duke kernel: Registered device AU0828 [Hauppauge HVR950Q]
Mar 13 14:29:56 duke kernel: usbcore: registered new interface driver au0828
Mar 13 14:29:56 duke kernel: generic-usb 0003:051D:0002.0004: hiddev1: USB HID v1.10 Device [American Power Conversion Back-UPS XS 1300 LCD FW:836.H8 .D USB FW:H8 ] on usb-0000:00:1a.7-3.4/input0
Mar 13 14:29:56 duke kernel: kjournald starting. Commit interval 5 seconds
Mar 13 14:29:56 duke kernel: EXT3-fs (sda1): using internal journal
Mar 13 14:29:56 duke kernel: EXT3-fs (sda1): mounted filesystem with writeback data mode
Mar 13 14:29:56 duke kernel: XFS mounting filesystem sdb1
Mar 13 14:29:56 duke kernel: Ending clean XFS mount for filesystem: sdb1
Mar 13 14:29:56 duke kernel: sky2 eth0: enabling interface
Mar 13 14:29:56 duke kernel: eth1: link up, 100Mbps, full-duplex, lpa 0x41E1
Mar 13 14:29:56 duke kernel: eth1: link up, 100Mbps, full-duplex, lpa 0x41E1
Mar 13 14:29:56 duke kernel: sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
Mar 13 14:29:56 duke kernel: warning: `ntpd' uses 32-bit capabilities (legacy support in use)
Mar 13 14:29:56 duke logger: /etc/rc2.d/S13local start
Mar 13 14:29:56 duke kernel: ata1.00: configured for UDMA/133
Mar 13 14:29:56 duke kernel: ata1: EH complete
Mar 13 14:29:56 duke kernel: ata5.00: configured for UDMA/133
Mar 13 14:29:56 duke kernel: ata5: EH complete
Mar 13 14:29:56 duke sshd[3662]: Server listening on 0.0.0.0 port 22.
Mar 13 14:29:56 duke /usr/sbin/gpm[3682]: *** info [daemon/startup.c(131)]:
Mar 13 14:29:56 duke /usr/sbin/gpm[3682]: Started gpm successfully. Entered daemon mode.
Mar 13 14:29:56 duke mysqld_safe[3761]: started
Mar 13 14:29:56 duke mysqld[3764]: 100313 14:29:56 [Warning] option 'net_buffer_length': unsigned value 8388608 adjusted to 1048576
Mar 13 14:29:56 duke mysqld[3764]: 100313 14:29:56 InnoDB: Started; log sequence number 0 2482424
Mar 13 14:29:56 duke mysqld[3764]: 100313 14:29:56 [Note] /usr/sbin/mysqld: ready for connections.
Mar 13 14:29:56 duke mysqld[3764]: Version: '5.0.67-0ubuntu6.1' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu)
Mar 13 14:29:57 duke /etc/mysql/debian-start[3803]: Upgrading MySQL tables if necessary.
Mar 13 14:29:57 duke /etc/mysql/debian-start[3807]: Looking for 'mysql' in: /usr/bin/mysql
Mar 13 14:29:57 duke /etc/mysql/debian-start[3807]: Looking for 'mysqlcheck' in: /usr/bin/mysqlcheck
Mar 13 14:29:57 duke /etc/mysql/debian-start[3807]: This installation of MySQL is already upgraded to 5.0.67, use --force if you still need to run mysql_upgrade
Mar 13 14:29:57 duke /etc/mysql/debian-start[3819]: Checking for insecure root accounts.
Mar 13 14:29:57 duke /etc/mysql/debian-start[3823]: WARNING: mysql.user contains 3 root accounts without password!
Mar 13 14:29:57 duke /etc/mysql/debian-start[3824]: Triggering myisam-recover for all MyISAM tables
Mar 13 14:29:58 duke acpid: client connected from 4050[113:122]
Mar 13 14:29:58 duke ntpd[3550]: ntpd exiting on signal 15
Mar 13 14:29:58 duke kernel: cx18 0000:05:03.0: firmware: requesting v4l-cx23418-cpu.fw
Mar 13 14:29:59 duke ntpdate[4123]: step time server 10.0.0.2 offset 0.615512 sec
Mar 13 14:29:59 duke ntpd[4179]: ntpd 4.2.4p4@xxxxxxxx Fri Dec 4 19:14:37 UTC 2009 (1)
Mar 13 14:29:59 duke ntpd[4180]: precision = 1.000 usec
Mar 13 14:29:59 duke ntpd[4180]: Listening on interface #0 wildcard, 0.0.0.0#123 Disabled
Mar 13 14:29:59 duke ntpd[4180]: Listening on interface #1 lo, 127.0.0.1#123 Enabled
Mar 13 14:29:59 duke ntpd[4180]: Listening on interface #2 eth0, 10.0.0.18#123 Enabled
Mar 13 14:29:59 duke ntpd[4180]: Listening on interface #3 eth1, 169.254.4.100#123 Enabled
Mar 13 14:29:59 duke ntpd[4180]: kernel time sync status 0040
Mar 13 14:29:59 duke ntpd[4180]: frequency initialized 8.136 PPM from /var/lib/ntp/ntp.drift
Mar 13 14:29:59 duke kernel: cx18-0: loaded v4l-cx23418-cpu.fw firmware (158332 bytes)
Mar 13 14:29:59 duke kernel: cx18 0000:05:03.0: firmware: requesting v4l-cx23418-apu.fw
Mar 13 14:29:59 duke kernel: cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes)
Mar 13 14:29:59 duke kernel: cx18-0: FW version: 0.0.74.0 (Release 2007/03/12)
Mar 13 14:29:59 duke kernel: cx18 0000:05:03.0: firmware: requesting v4l-cx23418-cpu.fw
Mar 13 14:29:59 duke kernel: cx18 0000:05:03.0: firmware: requesting v4l-cx23418-apu.fw
Mar 13 14:30:00 duke kernel: cx18 0000:05:03.0: firmware: requesting v4l-cx23418-dig.fw
Mar 13 14:30:00 duke kernel: cx18-0 843: loaded v4l-cx23418-dig.fw firmware (16382 bytes)
Mar 13 14:30:00 duke kernel: cx18-0 843: verified load of v4l-cx23418-dig.fw firmware (16382 bytes)
Mar 13 14:30:01 duke kernel: ivtv 0000:05:02.0: firmware: requesting v4l-cx2341x-enc.fw
Mar 13 14:30:01 duke kernel: ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
Mar 13 14:30:01 duke kernel: ivtv0: Encoder revision: 0x02060039
Mar 13 14:30:01 duke kernel: ata1.00: configured for UDMA/133
Mar 13 14:30:01 duke kernel: ata1: EH complete
Mar 13 14:30:01 duke kernel: ata5.00: configured for UDMA/133
Mar 13 14:30:01 duke kernel: ata5: EH complete
Mar 13 14:30:03 duke logger: /usr/local/bin/enable_hauppauge_remote.sh: reconfiguring driver
Mar 13 14:30:04 duke kernel: input: i2c IR (Hauppauge) as /class/input/input5
Mar 13 14:30:04 duke kernel: Creating IR device irrcv0
Mar 13 14:30:04 duke kernel: ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-0/0-0018/ir0 [ivtv i2c driver #0]
Mar 13 14:30:04 duke logger: /usr/local/bin/enable_hauppauge_remote.sh: waiting for device(s)
Mar 13 14:30:04 duke logger[4278]: /usr/bin/input-kbd -f /usr/local/bin/hauppauge_remote.conf 5
Mar 13 14:30:04 duke logger: /dev/video1: fix_hvr1600_stutter.sh: Pre-initializing
Mar 13 14:30:09 duke logger: /dev/video1: fix_hvr1600_stutter.sh: HVR1600/cx18 audio bug, reloading cx18 driver
Mar 13 14:30:09 duke logger: /dev/video1: fix_hvr1600_stutter.sh: rmmod cx18 failed
Mar 13 14:30:09 duke nanny.mythbackend[4350]: mythbackend[4352] started
Mar 13 14:30:09 duke gdm[4386]: WARNING: Didn't understand `' (expected true or false)
Mar 13 14:30:09 duke acpid: client connected from 4399[0:0]
Mar 13 14:30:10 duke /usr/sbin/cron[4452]: (CRON) INFO (pidfile fd = 3)
Mar 13 14:30:10 duke /usr/sbin/cron[4453]: (CRON) STARTUP (fork ok)
Mar 13 14:30:10 duke /usr/sbin/cron[4453]: (CRON) INFO (Running @reboot jobs)
Mar 13 14:30:10 duke rpc.statd[4488]: Version 1.1.2 Starting
Mar 13 14:30:10 duke kernel: RPC: Registered udp transport module.
Mar 13 14:30:10 duke kernel: RPC: Registered tcp transport module.
Mar 13 14:30:10 duke kernel: RPC: Registered tcp NFSv4.1 backchannel transport module.
Mar 13 14:30:10 duke acpid: client connected from 4399[0:0]
Mar 13 14:30:10 duke kernel: Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
Mar 13 14:30:10 duke kernel: NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
Mar 13 14:30:10 duke kernel: NFSD: starting 90-second grace period
Mar 13 14:30:11 duke logger: /etc/rc2.d/S98local start
Mar 13 14:30:11 duke kernel: ata1.00: configured for UDMA/133
Mar 13 14:30:11 duke kernel: ata1: EH complete
Mar 13 14:30:11 duke kernel: ata5.00: configured for UDMA/133
Mar 13 14:30:11 duke kernel: ata5: EH complete
Mar 13 14:30:11 duke gdm[4393]: pam_unix(gdm-autologin:session): session opened for user mlord by (uid=0)
Mar 13 14:30:11 duke gdm[4393]: pam_ck_connector(gdm-autologin:session): nox11 mode, ignoring PAM_TTY :0
Mar 13 14:30:11 duke apcupsd[4427]: NIS server startup succeeded
Mar 13 14:30:11 duke apcupsd[4427]: apcupsd 3.14.4 (18 May 2008) debian startup succeeded
Mar 13 14:30:12 duke nanny.vfd_updater[4865]: vfd_updater[4866] started
Mar 13 14:30:12 duke vfd_updater[4866]: connect(): Connection refused
Mar 13 14:30:14 duke kernel: xc5000: waiting for firmware upload (dvb-fe-xc5000-1.6.114.fw)...
Mar 13 14:30:14 duke kernel: usb 2-3.2: firmware: requesting dvb-fe-xc5000-1.6.114.fw
Mar 13 14:30:14 duke kernel: xc5000: firmware read 12401 bytes.
Mar 13 14:30:14 duke kernel: xc5000: firmware uploading...
Mar 13 14:30:21 duke kernel: xc5000: firmware upload complete...
Mar 13 14:30:22 duke /usr/local/bin/diseqc_switcher[4909]: Selecting '2B'
Mar 13 14:30:22 duke /usr/local/bin/diseqc_switcher[4909]: writing 0x04 [- - - - - 1 - -]
Mar 13 14:30:23 duke logger: /dev/video1: channel_change: hit HVR1600/cx18 audio bug.. attempting workaround
Mar 13 14:30:24 duke logger: /dev/video1: channel_change: hit HVR1600/cx18 audio bug.. workaround failed
Mar 13 14:30:25 duke /usr/local/bin/diseqc_switcher[4962]: Selecting '1B'
Mar 13 14:30:25 duke /usr/local/bin/diseqc_switcher[4962]: writing 0x05 [- - - - - 1 - 1]
Mar 13 14:30:30 duke logger: /usr/local/bin/set_wakeup_alarm.sh: mythbackend started by 'auto'
Mar 13 14:30:31 duke vfd_updater[4866]: mythbackend: ACCEPT, MYTH_PROTOCOL_VERSION 40
Mar 13 14:30:31 duke logger: /usr/local/bin/set_wakeup_alarm.sh: setting wakeup alarm the old fashioned way
Mar 13 14:30:31 duke logger: /usr/local/bin/set_wakeup_alarm.sh: setting wakeup alarm to (1268573430) UTC '2010-03-14 13:30:30' (local '2010-03-14 09:30:30')
Mar 13 14:30:31 duke logger: /usr/local/bin/set_wakeup_alarm.sh: echo 2010-03-14 13:30:30 > /proc/acpi/alarm
Mar 13 14:30:31 duke logger: /usr/local/bin/set_wakeup_alarm.sh: RTC alarm readback: 2010-03-14 13:30:30
Mar 13 14:30:31 duke logger: /usr/local/bin/set_wakeup_alarm.sh: UTC time now: 2010-03-13 19:30:31
Mar 13 14:30:31 duke logger: /usr/local/bin/set_wakeup_alarm.sh: next wakeup: 2010-03-14 09:30:30
Mar 13 14:30:31 duke /usr/local/bin/diseqc_switcher[5073]: Selecting '1C'
Mar 13 14:30:31 duke /usr/local/bin/diseqc_switcher[5073]: writing 0x06 [- - - - - 1 1 -]
Mar 13 14:30:33 duke /usr/local/bin/diseqc_switcher[5082]: Selecting '2B'
Mar 13 14:30:33 duke /usr/local/bin/diseqc_switcher[5082]: writing 0x06 [- - - - - 1 1 -]
Mar 13 14:30:36 duke logger: /dev/video1: channel_change: hit HVR1600/cx18 audio bug.. attempting workaround
Mar 13 14:30:37 duke logger: /dev/video1: channel_change: hit HVR1600/cx18 audio bug.. workaround failed
Mar 13 14:32:32 duke /usr/local/bin/diseqc_switcher[5485]: Selecting '2C'
Mar 13 14:32:32 duke /usr/local/bin/diseqc_switcher[5485]: writing 0x0a [- - - - 1 - 1 -]
Mar 13 14:32:34 duke logger: /dev/video1: channel_change: hit HVR1600/cx18 audio bug.. attempting workaround
Mar 13 14:32:34 duke logger: /dev/video1: channel_change: hit HVR1600/cx18 audio bug.. workaround failed
Mar 13 14:34:18 duke ntpd[4180]: synchronized to 10.0.0.2, stratum 3
Mar 13 14:34:19 duke ntpd[4180]: time reset +0.373377 s
Mar 13 14:34:19 duke ntpd[4180]: kernel time sync status change 0001
Mar 13 14:42:16 duke kernel: cx18-0: ================= START STATUS CARD #0 =================
Mar 13 14:42:16 duke kernel: cx18-0: Version: 1.4.0 Card: Hauppauge HVR-1600
Mar 13 14:42:16 duke kernel: tveeprom 1-0050: Hauppauge model 74551, rev C1A3, serial# 1752579
Mar 13 14:42:16 duke kernel: tveeprom 1-0050: MAC address is 00:0d:fe:1a:be:03
Mar 13 14:42:16 duke kernel: tveeprom 1-0050: tuner model is TCL MFNM05-4 (idx 103, type 43)
Mar 13 14:42:16 duke kernel: tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
Mar 13 14:42:16 duke kernel: tveeprom 1-0050: audio processor is CX23418 (idx 38)
Mar 13 14:42:16 duke kernel: tveeprom 1-0050: decoder processor is CX23418 (idx 31)
Mar 13 14:42:16 duke kernel: tveeprom 1-0050: has radio
Mar 13 14:42:16 duke kernel: cx18-0 843: Video signal: present
Mar 13 14:42:16 duke kernel: cx18-0 843: Detected format: NTSC-M
Mar 13 14:42:16 duke kernel: cx18-0 843: Specified standard: NTSC-M
Mar 13 14:42:16 duke kernel: cx18-0 843: Specified video input: Composite 7
Mar 13 14:42:16 duke kernel: cx18-0 843: Specified audioclock freq: 48000 Hz
Mar 13 14:42:16 duke kernel: cx18-0 843: Detected audio mode: mono
Mar 13 14:42:16 duke kernel: cx18-0 843: Detected audio standard: no detected audio standard
Mar 13 14:42:16 duke kernel: cx18-0 843: Audio muted: yes
Mar 13 14:42:16 duke kernel: cx18-0 843: Audio microcontroller: running
Mar 13 14:42:16 duke kernel: cx18-0 843: Configured audio standard: automatic detection
Mar 13 14:42:16 duke kernel: cx18-0 843: Configured audio system: BTSC
Mar 13 14:42:16 duke kernel: cx18-0 843: Specified audio input: Tuner (In8)
Mar 13 14:42:16 duke kernel: cx18-0 843: Preferred audio mode: stereo
Mar 13 14:42:16 duke kernel: cx18-0 gpio-reset-ctrl: GPIO: direction 0x00003001, value 0x00003001
Mar 13 14:42:16 duke kernel: tda9887 2-0043: Data bytes: b=0x14 c=0x30 e=0x44
Mar 13 14:42:16 duke kernel: tuner 2-0061: Tuner mode: analog TV
Mar 13 14:42:16 duke kernel: tuner 2-0061: Frequency: 531.25 MHz
Mar 13 14:42:16 duke kernel: tuner 2-0061: Standard: 0x0000b000
Mar 13 14:42:16 duke kernel: cs5345 1-004c: Input: 1
Mar 13 14:42:16 duke kernel: cs5345 1-004c: Volume: 0 dB
Mar 13 14:42:16 duke kernel: cx18-0: Video Input: Tuner 1
Mar 13 14:42:16 duke kernel: cx18-0: Audio Input: Tuner 1
Mar 13 14:42:16 duke kernel: cx18-0: GPIO: direction 0x00003001, value 0x00003001
Mar 13 14:42:16 duke kernel: cx18-0: Tuner: TV
Mar 13 14:42:16 duke kernel: cx18-0: Stream: MPEG-2 Program Stream
Mar 13 14:42:16 duke kernel: cx18-0: VBI Format: Private packet, IVTV format
Mar 13 14:42:16 duke kernel: cx18-0: Video: 720x480, 30 fps
Mar 13 14:42:16 duke kernel: cx18-0: Video: MPEG-2, 4x3, Variable Bitrate, 13000000, Peak 15000000
Mar 13 14:42:16 duke kernel: cx18-0: Video: GOP Size 15, 2 B-Frames, GOP Closure
Mar 13 14:42:16 duke kernel: cx18-0: Audio: 48 kHz, MPEG-1/2 Layer II, 224 kbps, Stereo, No Emphasis, No CRC
Mar 13 14:42:16 duke kernel: cx18-0: Spatial Filter: Manual, Luma 1D Horizontal, Chroma 1D Horizontal, 0
Mar 13 14:42:16 duke kernel: cx18-0: Temporal Filter: Manual, 8
Mar 13 14:42:16 duke kernel: cx18-0: Median Filter: Off, Luma [0, 255], Chroma [0, 255]
Mar 13 14:42:16 duke kernel: cx18-0: Status flags: 0x00200001
Mar 13 14:42:16 duke kernel: cx18-0: Stream encoder MPEG: status 0x0000, 0% of 2048 KiB (64 buffers) in use
Mar 13 14:42:16 duke kernel: cx18-0: Stream encoder YUV: status 0x0000, 0% of 2025 KiB (20 buffers) in use
Mar 13 14:42:16 duke kernel: cx18-0: Stream encoder VBI: status 0x0000, 0% of 1015 KiB (20 buffers) in use
Mar 13 14:42:16 duke kernel: cx18-0: Stream encoder PCM audio: status 0x0000, 0% of 1024 KiB (256 buffers) in use
Mar 13 14:42:16 duke kernel: cx18-0: Read MPEG/VBI: 9176956/20328 bytes
Mar 13 14:42:16 duke kernel: cx18-0: ================== END STATUS CARD #0 ==================
Mar 13 14:43:03 duke ntpd[4180]: synchronized to 10.0.0.2, stratum 3
