Hi Laurent, > -----Original Message----- > From: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> > Sent: Wednesday, May 27, 2020 9:42 PM > To: Vishal Sagar <vsagar@xxxxxxxxxx> > Cc: Hyun Kwon <hyunk@xxxxxxxxxx>; mchehab@xxxxxxxxxx; > robh+dt@xxxxxxxxxx; mark.rutland@xxxxxxx; Michal Simek > <michals@xxxxxxxxxx>; linux-media@xxxxxxxxxxxxxxx; > devicetree@xxxxxxxxxxxxxxx; hans.verkuil@xxxxxxxxx; linux-arm- > kernel@xxxxxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; Dinesh Kumar > <dineshk@xxxxxxxxxx>; Sandip Kothari <sandipk@xxxxxxxxxx>; Luca Ceresoli > <luca@xxxxxxxxxxxxxxxx>; Jacopo Mondi <jacopo@xxxxxxxxxx> > Subject: Re: [PATCH v14 1/2] media: dt-bindings: media: xilinx: Add Xilinx MIPI > CSI-2 Rx Subsystem > > Hi Vishal, > > Thank you for the patch. > > On Wed, May 27, 2020 at 07:27:18PM +0530, Vishal Sagar wrote: > > Add bindings documentation for Xilinx MIPI CSI-2 Rx Subsystem. > > > > The Xilinx MIPI CSI-2 Rx Subsystem consists of a CSI-2 Rx controller, > > a D-PHY in Rx mode and a Video Format Bridge. > > > > Signed-off-by: Vishal Sagar <vishal.sagar@xxxxxxxxxx> > > Reviewed-by: Hyun Kwon <hyun.kwon@xxxxxxxxxx> > > Reviewed-by: Rob Herring <robh@xxxxxxxxxx> > > Reviewed-by: Luca Ceresoli <luca@xxxxxxxxxxxxxxxx> > > Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> > > --- > > v14 > > - Removed xlnx,csi-pxl-format from required properties > > - Added dependency of xlnx,csi-pxl-format on xlnx,vfb > > - End the yaml file with ... > > - Added Reviewed by Laurent > > > > v13 > > - Based on Laurent's suggestions > > - Fixed the datatypes values as minimum and maximum > > - condition added for en-vcx property > > > > v12 > > - Moved to yaml format > > - Update CSI-2 and D-PHY > > - Mention that bindings for D-PHY not here > > - reset -> video-reset > > > > v11 > > - Modify compatible string from 4.0 to 5.0 > > > > v10 > > - No changes > > > > v9 > > - Fix xlnx,vfb description. > > - s/Optional/Required endpoint property. > > - Move data-lanes description from Ports to endpoint property section. > > > > v8 > > - Added reset-gpios optional property to assert video_aresetn > > > > v7 > > - Removed the control name from dt bindings > > - Updated the example dt node name to csi2rx > > > > v6 > > - Added "control" after V4L2_CID_XILINX_MIPICSISS_ACT_LANES as > > suggested by Luca > > - Added reviewed by Rob Herring > > > > v5 > > - Incorporated comments by Luca Cersoli > > - Removed DPHY clock from description and example > > - Removed bayer pattern from device tree MIPI CSI IP > > doesn't deal with bayer pattern. > > > > v4 > > - Added reviewed by Hyun Kwon > > > > v3 > > - removed interrupt parent as suggested by Rob > > - removed dphy clock > > - moved vfb to optional properties > > - Added required and optional port properties section > > - Added endpoint property section > > > > v2 > > - updated the compatible string to latest version supported > > - removed DPHY related parameters > > - added CSI v2.0 related property (including VCX for supporting upto 16 > > virtual channels). > > - modified csi-pxl-format from string to unsigned int type where the value > > is as per the CSI specification > > - Defined port 0 and port 1 as sink and source ports. > > - Removed max-lanes property as suggested by Rob and Sakari > > > > .../bindings/media/xilinx/xlnx,csi2rxss.yaml | 237 > +++++++++++++++++++++ > > 1 file changed, 237 insertions(+) > > create mode 100644 > > Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml > > > > diff --git > > a/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml > > b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml > > new file mode 100644 > > index 0000000..2282231 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yam > > +++ l > > @@ -0,0 +1,237 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/media/xilinx/xlnx,csi2rxss.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Xilinx MIPI CSI-2 Receiver Subsystem > > + > > +maintainers: > > + - Vishal Sagar <vishal.sagar@xxxxxxxxxx> > > + > > +description: | > > + The Xilinx MIPI CSI-2 Receiver Subsystem is used to capture MIPI > > +CSI-2 > > + traffic from compliant camera sensors and send the output as AXI4 > > +Stream > > + video data for image processing. > > + The subsystem consists of a MIPI D-PHY in slave mode which captures > > +the > > + data packets. This is passed along the MIPI CSI-2 Rx IP which > > +extracts the > > + packet data. The optional Video Format Bridge (VFB) converts this > > +data to > > + AXI4 Stream video data. > > + For more details, please refer to PG232 Xilinx MIPI CSI-2 Receiver > Subsystem. > > + Please note that this bindings includes only the MIPI CSI-2 Rx > > +controller > > + and Video Format Bridge and not D-PHY. > > + > > +properties: > > + compatible: > > + items: > > + - enum: > > + - xlnx,mipi-csi2-rx-subsystem-5.0 > > + > > + reg: > > + maxItems: 1 > > + > > + interrupts: > > + maxItems: 1 > > + > > + clocks: > > + description: List of clock specifiers > > + items: > > + - description: AXI Lite clock > > + - description: Video clock > > + > > + clock-names: > > + items: > > + - const: lite_aclk > > + - const: video_aclk > > + > > + xlnx,csi-pxl-format: > > + description: | > > + This denotes the CSI Data type selected in hw design. > > + Packets other than this data type (except for RAW8 and > > + User defined data types) will be filtered out. > > + Possible values are as below - > > + 0x1e - YUV4228B > > + 0x1f - YUV42210B > > + 0x20 - RGB444 > > + 0x21 - RGB555 > > + 0x22 - RGB565 > > + 0x23 - RGB666 > > + 0x24 - RGB888 > > + 0x28 - RAW6 > > + 0x29 - RAW7 > > + 0x2a - RAW8 > > + 0x2b - RAW10 > > + 0x2c - RAW12 > > + 0x2d - RAW14 > > + 0x2e - RAW16 > > + 0x2f - RAW20 > > + allOf: > > + - $ref: /schemas/types.yaml#/definitions/uint32 > > + - anyOf: > > + - minimum: 0x1e > > + - maximum: 0x24 > > + - minimum: 0x28 > > + - maximum: 0x2f > > + > > + xlnx,vfb: > > + type: boolean > > + description: Present when Video Format Bridge is enabled in IP > > + configuration > > + > > + xlnx,en-csi-v2-0: > > + type: boolean > > + description: Present if CSI v2 is enabled in IP configuration. > > + > > + xlnx,en-vcx: > > + type: boolean > > + description: | > > + When present, there are maximum 16 virtual channels, else only 4. > > + > > + xlnx,en-active-lanes: > > + type: boolean > > + description: | > > + Present if the number of active lanes can be re-configured at > > + runtime in the Protocol Configuration Register. Otherwise all lanes, > > + as set in IP configuration, are always active. > > + > > + video-reset-gpios: > > + description: Optional specifier for a GPIO that asserts video_aresetn. > > + maxItems: 1 > > + > > + ports: > > + type: object > > + > > + properties: > > + port@0: > > + type: object > > + description: | > > + Input / sink port node, single endpoint describing the > > + CSI-2 transmitter. > > + > > + properties: > > + reg: > > + const: 0 > > + > > + endpoint: > > + type: object > > + > > + properties: > > + > > + data-lanes: > > + description: | > > + This is required only in the sink port 0 endpoint which > > + connects to MIPI CSI-2 source like sensor. > > + The possible values are - > > + 1 - For 1 lane enabled in IP. > > + 1 2 - For 2 lanes enabled in IP. > > + 1 2 3 - For 3 lanes enabled in IP. > > + 1 2 3 4 - For 4 lanes enabled in IP. > > + items: > > + - const: 1 > > + - const: 2 > > + - const: 3 > > + - const: 4 > > + > > + remote-endpoint: true > > + > > + required: > > + - data-lanes > > + - remote-endpoint > > + > > + additionalProperties: false > > + > > + additionalProperties: false > > + > > + port@1: > > + type: object > > + description: | > > + Output / source port node, endpoint describing modules > > + connected the CSI-2 receiver. > > + > > + properties: > > + > > + reg: > > + const: 1 > > + > > + endpoint: > > + type: object > > + > > + properties: > > + > > + remote-endpoint: true > > + > > + required: > > + - remote-endpoint > > + > > + additionalProperties: false > > + > > + additionalProperties: false > > + > > +required: > > + - compatible > > + - reg > > + - interrupts > > + - clocks > > + - clock-names > > + - ports > > + > > +allOf: > > + - if: > > + required: > > + - xlnx,vfb > > + then: > > + required: > > + - xlnx,csi-pxl-format > > + else: > > + properties: > > + xlnx,csi-pxl-format: false > > + > > + - if: > > + not: > > + required: > > + - xlnx,en-csi-v2-0 > > + then: > > + properties: > > + xlnx,en-vcx: false > > There's an indentation problem here, it should be > > allOf: > - if: > required: > - xlnx,vfb > then: > required: > - xlnx,csi-pxl-format > else: > properties: > xlnx,csi-pxl-format: false > > - if: > not: > required: > - xlnx,en-csi-v2-0 > then: > properties: > xlnx,en-vcx: false > > Have you run the bindings checks ? > > make > DT_SCHEMA_FILES=Documentation/devicetree/bindings/media/xilinx/xlnx,csi > 2rxss.yaml dt_binding_check > > It would have caught the issue. > By mistake the incorrect patch was sent. Apologies for this. > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + #include <dt-bindings/gpio/gpio.h> > > + xcsi2rxss_1: csi2rx@a0020000 { > > + compatible = "xlnx,mipi-csi2-rx-subsystem-5.0"; > > + reg = <0x0 0xa0020000 0x0 0x10000>; > > I think I mentioned in a previous review that this should be > > reg = <0xa0020000 0x10000>; > > even if it doesn't match what the real values, as dt_binding_check compiles > the examples in the context of a bus that has #address-cells = <1> and #size- > cells = <1>. > > I can fix these when applying the patches to my tree if that's OK with you, and > send a pull request. > Yes that is fine. Thanks! > > + interrupt-parent = <&gic>; > > + interrupts = <0 95 4>; > > + xlnx,csi-pxl-format = <0x2a>; > > + xlnx,vfb; > > + xlnx,en-active-lanes; > > + xlnx,en-csi-v2-0; > > + xlnx,en-vcx; > > + clock-names = "lite_aclk", "video_aclk"; > > + clocks = <&misc_clk_0>, <&misc_clk_1>; > > + video-reset-gpios = <&gpio 86 GPIO_ACTIVE_LOW>; > > + > > + ports { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + port@0 { > > + /* Sink port */ > > + reg = <0>; > > + csiss_in: endpoint { > > + data-lanes = <1 2 3 4>; > > + /* MIPI CSI-2 Camera handle */ > > + remote-endpoint = <&camera_out>; > > + }; > > + }; > > + port@1 { > > + /* Source port */ > > + reg = <1>; > > + csiss_out: endpoint { > > + remote-endpoint = <&vproc_in>; > > + }; > > + }; > > + }; > > + }; > > +... > > -- > Regards, > > Laurent Pinchart Regards Vishal Sagar
