Add bindings documentation for Xilinx MIPI CSI-2 Rx Subsystem. The Xilinx MIPI CSI-2 Rx Subsystem consists of a CSI-2 Rx controller, a D-PHY in Rx mode and a Video Format Bridge. Signed-off-by: Vishal Sagar <vishal.sagar@xxxxxxxxxx> Reviewed-by: Hyun Kwon <hyun.kwon@xxxxxxxxxx> Reviewed-by: Rob Herring <robh@xxxxxxxxxx> Reviewed-by: Luca Ceresoli <luca@xxxxxxxxxxxxxxxx> Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> --- v14 - Removed xlnx,csi-pxl-format from required properties - Added dependency of xlnx,csi-pxl-format on xlnx,vfb - End the yaml file with ... - Added Reviewed by Laurent v13 - Based on Laurent's suggestions - Fixed the datatypes values as minimum and maximum - condition added for en-vcx property v12 - Moved to yaml format - Update CSI-2 and D-PHY - Mention that bindings for D-PHY not here - reset -> video-reset v11 - Modify compatible string from 4.0 to 5.0 v10 - No changes v9 - Fix xlnx,vfb description. - s/Optional/Required endpoint property. - Move data-lanes description from Ports to endpoint property section. v8 - Added reset-gpios optional property to assert video_aresetn v7 - Removed the control name from dt bindings - Updated the example dt node name to csi2rx v6 - Added "control" after V4L2_CID_XILINX_MIPICSISS_ACT_LANES as suggested by Luca - Added reviewed by Rob Herring v5 - Incorporated comments by Luca Cersoli - Removed DPHY clock from description and example - Removed bayer pattern from device tree MIPI CSI IP doesn't deal with bayer pattern. v4 - Added reviewed by Hyun Kwon v3 - removed interrupt parent as suggested by Rob - removed dphy clock - moved vfb to optional properties - Added required and optional port properties section - Added endpoint property section v2 - updated the compatible string to latest version supported - removed DPHY related parameters - added CSI v2.0 related property (including VCX for supporting upto 16 virtual channels). - modified csi-pxl-format from string to unsigned int type where the value is as per the CSI specification - Defined port 0 and port 1 as sink and source ports. - Removed max-lanes property as suggested by Rob and Sakari .../bindings/media/xilinx/xlnx,csi2rxss.yaml | 237 +++++++++++++++++++++ 1 file changed, 237 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml new file mode 100644 index 0000000..2282231 --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,csi2rxss.yaml @@ -0,0 +1,237 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/xilinx/xlnx,csi2rxss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Xilinx MIPI CSI-2 Receiver Subsystem + +maintainers: + - Vishal Sagar <vishal.sagar@xxxxxxxxxx> + +description: | + The Xilinx MIPI CSI-2 Receiver Subsystem is used to capture MIPI CSI-2 + traffic from compliant camera sensors and send the output as AXI4 Stream + video data for image processing. + The subsystem consists of a MIPI D-PHY in slave mode which captures the + data packets. This is passed along the MIPI CSI-2 Rx IP which extracts the + packet data. The optional Video Format Bridge (VFB) converts this data to + AXI4 Stream video data. + For more details, please refer to PG232 Xilinx MIPI CSI-2 Receiver Subsystem. + Please note that this bindings includes only the MIPI CSI-2 Rx controller + and Video Format Bridge and not D-PHY. + +properties: + compatible: + items: + - enum: + - xlnx,mipi-csi2-rx-subsystem-5.0 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + description: List of clock specifiers + items: + - description: AXI Lite clock + - description: Video clock + + clock-names: + items: + - const: lite_aclk + - const: video_aclk + + xlnx,csi-pxl-format: + description: | + This denotes the CSI Data type selected in hw design. + Packets other than this data type (except for RAW8 and + User defined data types) will be filtered out. + Possible values are as below - + 0x1e - YUV4228B + 0x1f - YUV42210B + 0x20 - RGB444 + 0x21 - RGB555 + 0x22 - RGB565 + 0x23 - RGB666 + 0x24 - RGB888 + 0x28 - RAW6 + 0x29 - RAW7 + 0x2a - RAW8 + 0x2b - RAW10 + 0x2c - RAW12 + 0x2d - RAW14 + 0x2e - RAW16 + 0x2f - RAW20 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - anyOf: + - minimum: 0x1e + - maximum: 0x24 + - minimum: 0x28 + - maximum: 0x2f + + xlnx,vfb: + type: boolean + description: Present when Video Format Bridge is enabled in IP configuration + + xlnx,en-csi-v2-0: + type: boolean + description: Present if CSI v2 is enabled in IP configuration. + + xlnx,en-vcx: + type: boolean + description: | + When present, there are maximum 16 virtual channels, else only 4. + + xlnx,en-active-lanes: + type: boolean + description: | + Present if the number of active lanes can be re-configured at + runtime in the Protocol Configuration Register. Otherwise all lanes, + as set in IP configuration, are always active. + + video-reset-gpios: + description: Optional specifier for a GPIO that asserts video_aresetn. + maxItems: 1 + + ports: + type: object + + properties: + port@0: + type: object + description: | + Input / sink port node, single endpoint describing the + CSI-2 transmitter. + + properties: + reg: + const: 0 + + endpoint: + type: object + + properties: + + data-lanes: + description: | + This is required only in the sink port 0 endpoint which + connects to MIPI CSI-2 source like sensor. + The possible values are - + 1 - For 1 lane enabled in IP. + 1 2 - For 2 lanes enabled in IP. + 1 2 3 - For 3 lanes enabled in IP. + 1 2 3 4 - For 4 lanes enabled in IP. + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + + remote-endpoint: true + + required: + - data-lanes + - remote-endpoint + + additionalProperties: false + + additionalProperties: false + + port@1: + type: object + description: | + Output / source port node, endpoint describing modules + connected the CSI-2 receiver. + + properties: + + reg: + const: 1 + + endpoint: + type: object + + properties: + + remote-endpoint: true + + required: + - remote-endpoint + + additionalProperties: false + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - ports + +allOf: + - if: + required: + - xlnx,vfb + then: + required: + - xlnx,csi-pxl-format + else: + properties: + xlnx,csi-pxl-format: false + + - if: + not: + required: + - xlnx,en-csi-v2-0 + then: + properties: + xlnx,en-vcx: false + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + xcsi2rxss_1: csi2rx@a0020000 { + compatible = "xlnx,mipi-csi2-rx-subsystem-5.0"; + reg = <0x0 0xa0020000 0x0 0x10000>; + interrupt-parent = <&gic>; + interrupts = <0 95 4>; + xlnx,csi-pxl-format = <0x2a>; + xlnx,vfb; + xlnx,en-active-lanes; + xlnx,en-csi-v2-0; + xlnx,en-vcx; + clock-names = "lite_aclk", "video_aclk"; + clocks = <&misc_clk_0>, <&misc_clk_1>; + video-reset-gpios = <&gpio 86 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + /* Sink port */ + reg = <0>; + csiss_in: endpoint { + data-lanes = <1 2 3 4>; + /* MIPI CSI-2 Camera handle */ + remote-endpoint = <&camera_out>; + }; + }; + port@1 { + /* Source port */ + reg = <1>; + csiss_out: endpoint { + remote-endpoint = <&vproc_in>; + }; + }; + }; + }; +... -- 2.1.1
