On Wed, May 27, 2020 at 2:51 AM Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx> wrote: > > Hi Rob, > > Thanks for the review. Please see my replies below. > > On Tue, 2020-05-26 at 12:28 -0600, Rob Herring wrote: > > On Sat, May 23, 2020 at 04:41:02PM +0800, Dongchun Zhu wrote: > > > Add DT bindings documentation for Omnivision OV02A10 image sensor. > > > > > > Signed-off-by: Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx> > > > --- > > > .../bindings/media/i2c/ovti,ov02a10.yaml | 172 +++++++++++++++++++++ > > > MAINTAINERS | 7 + > > > 2 files changed, 179 insertions(+) > > > create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml > > > > > > diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml > > > new file mode 100644 > > > index 0000000..56f31b5 > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml > > > @@ -0,0 +1,172 @@ > > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > > > +# Copyright (c) 2020 MediaTek Inc. > > > +%YAML 1.2 > > > +--- > > > +$id: http://devicetree.org/schemas/media/i2c/ovti,ov02a10.yaml# > > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > > + > > > +title: Omnivision OV02A10 CMOS Sensor Device Tree Bindings > > > + > > > +maintainers: > > > + - Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx> > > > + > > > +description: |- > > > + The Omnivision OV02A10 is a low-cost, high performance, 1/5-inch, 2 megapixel > > > + image sensor, which is the latest production derived from Omnivision's CMOS > > > + image sensor technology. Ihis chip supports high frame rate speeds up to 30fps > > > + @ 1600x1200 (UXGA) resolution transferred over a 1-lane MIPI interface. The > > > + sensor output is available via CSI-2 serial data output. > > > + > > > +properties: > > > + compatible: > > > + const: ovti,ov02a10 > > > + > > > + reg: > > > + maxItems: 1 > > > + > > > + clocks: > > > + items: > > > + - description: top mux camtg clock > > > + - description: divider clock > > > + > > > + clock-names: > > > + items: > > > + - const: eclk > > > + - const: freq_mux > > > + > > > + clock-frequency: > > > + description: > > > + Frequency of the eclk clock in Hertz. > > > + > > Rob, shall we use 'maxItems: 1' to constrain property: clock-frequency? No, because it is a scalar, not an array. > Or could we adopt 'clock-frequency: true' directly here? As-is is fine. > > > + dovdd-supply: > > > + description: > > > + Definition of the regulator used as Digital I/O voltage supply. > > > + > > Shall we add 'maxItems: 1' here? No, supplies are always singular. > > > > + avdd-supply: > > > + description: > > > + Definition of the regulator used as Analog voltage supply. > > > + > > Ditto. > > > > + dvdd-supply: > > > + description: > > > + Definition of the regulator used as Digital core voltage supply. > > > + > > Ditto. > > > > + powerdown-gpios: > > > + description: > > > + Must be the device tree identifier of the GPIO connected to the > > > + PD_PAD pin. This pin is used to place the OV02A10 into Standby mode > > > + or Shutdown mode. As the line is active low, it should be > > > + marked GPIO_ACTIVE_LOW. > > > > Need to define how many GPIOs ('maxItems: 1') > > > > It would be fixed like this in next release. > powerdown-gpios: > maxItems: 1 > description: > Must be the device tree identifier of the GPIO connected to the > PD_PAD pin. This pin is used to place the OV02A10 into Standby mode > or Shutdown mode. As the line is active low, it should be > marked GPIO_ACTIVE_LOW. > > > > + > > > + reset-gpios: > > > + description: > > > + Must be the device tree identifier of the GPIO connected to the > > > + RST_PD pin. If specified, it will be asserted during driver probe. > > > + As the line is active high, it should be marked GPIO_ACTIVE_HIGH. > > > > Here too. > > > > Similar as 'powerdown-gpios'. > Fixed in next release. > > > > + > > > + rotation: > > > + description: > > > + Definition of the sensor's placement. > > > + allOf: > > > + - $ref: "/schemas/types.yaml#/definitions/uint32" > > > + - enum: > > > + - 0 # Sensor Mounted Upright > > > + - 180 # Sensor Mounted Upside Down > > > + default: 0 > > > + > > > + ovti,mipi-tx-speed: > > > + description: > > > + Indication of MIPI transmission speed select, which is to control D-PHY > > > + timing setting by adjusting MIPI clock voltage to improve the clock > > > + driver capability. > > > + allOf: > > > + - $ref: "/schemas/types.yaml#/definitions/uint32" > > > + - enum: > > > + - 0 # 20MHz - 30MHz > > > + - 1 # 30MHz - 50MHz > > > + - 2 # 50MHz - 75MHz > > > + - 3 # 75MHz - 100MHz > > > + - 4 # 100MHz - 130MHz > > > + default: 3 > > > + > > > + # See ../video-interfaces.txt for details > > > + port: > > > + type: object > > > + additionalProperties: false > > > > Should have a description of what data the port has. > > > > It would be updated as below in next release. > port: > type: object > additionalProperties: false > description: > Input port node, single endpoint describing the CSI-2 transmitter. Output? > > > > + > > > + properties: > > > + endpoint: > > > + type: object > > > + additionalProperties: false > > > + > > > + properties: > > Actually I wonder whether we need to declare 'clock-lanes' here? Yes, if you are using it. Rob
