Hi Rob, Thanks for the review. Please see my replies below. On Tue, 2020-05-26 at 12:28 -0600, Rob Herring wrote: > On Sat, May 23, 2020 at 04:41:02PM +0800, Dongchun Zhu wrote: > > Add DT bindings documentation for Omnivision OV02A10 image sensor. > > > > Signed-off-by: Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx> > > --- > > .../bindings/media/i2c/ovti,ov02a10.yaml | 172 +++++++++++++++++++++ > > MAINTAINERS | 7 + > > 2 files changed, 179 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml > > > > diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml > > new file mode 100644 > > index 0000000..56f31b5 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml > > @@ -0,0 +1,172 @@ > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > > +# Copyright (c) 2020 MediaTek Inc. > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/media/i2c/ovti,ov02a10.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Omnivision OV02A10 CMOS Sensor Device Tree Bindings > > + > > +maintainers: > > + - Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx> > > + > > +description: |- > > + The Omnivision OV02A10 is a low-cost, high performance, 1/5-inch, 2 megapixel > > + image sensor, which is the latest production derived from Omnivision's CMOS > > + image sensor technology. Ihis chip supports high frame rate speeds up to 30fps > > + @ 1600x1200 (UXGA) resolution transferred over a 1-lane MIPI interface. The > > + sensor output is available via CSI-2 serial data output. > > + > > +properties: > > + compatible: > > + const: ovti,ov02a10 > > + > > + reg: > > + maxItems: 1 > > + > > + clocks: > > + items: > > + - description: top mux camtg clock > > + - description: divider clock > > + > > + clock-names: > > + items: > > + - const: eclk > > + - const: freq_mux > > + > > + clock-frequency: > > + description: > > + Frequency of the eclk clock in Hertz. > > + Rob, shall we use 'maxItems: 1' to constrain property: clock-frequency? Or could we adopt 'clock-frequency: true' directly here? > > + dovdd-supply: > > + description: > > + Definition of the regulator used as Digital I/O voltage supply. > > + Shall we add 'maxItems: 1' here? > > + avdd-supply: > > + description: > > + Definition of the regulator used as Analog voltage supply. > > + Ditto. > > + dvdd-supply: > > + description: > > + Definition of the regulator used as Digital core voltage supply. > > + Ditto. > > + powerdown-gpios: > > + description: > > + Must be the device tree identifier of the GPIO connected to the > > + PD_PAD pin. This pin is used to place the OV02A10 into Standby mode > > + or Shutdown mode. As the line is active low, it should be > > + marked GPIO_ACTIVE_LOW. > > Need to define how many GPIOs ('maxItems: 1') > It would be fixed like this in next release. powerdown-gpios: maxItems: 1 description: Must be the device tree identifier of the GPIO connected to the PD_PAD pin. This pin is used to place the OV02A10 into Standby mode or Shutdown mode. As the line is active low, it should be marked GPIO_ACTIVE_LOW. > > + > > + reset-gpios: > > + description: > > + Must be the device tree identifier of the GPIO connected to the > > + RST_PD pin. If specified, it will be asserted during driver probe. > > + As the line is active high, it should be marked GPIO_ACTIVE_HIGH. > > Here too. > Similar as 'powerdown-gpios'. Fixed in next release. > > + > > + rotation: > > + description: > > + Definition of the sensor's placement. > > + allOf: > > + - $ref: "/schemas/types.yaml#/definitions/uint32" > > + - enum: > > + - 0 # Sensor Mounted Upright > > + - 180 # Sensor Mounted Upside Down > > + default: 0 > > + > > + ovti,mipi-tx-speed: > > + description: > > + Indication of MIPI transmission speed select, which is to control D-PHY > > + timing setting by adjusting MIPI clock voltage to improve the clock > > + driver capability. > > + allOf: > > + - $ref: "/schemas/types.yaml#/definitions/uint32" > > + - enum: > > + - 0 # 20MHz - 30MHz > > + - 1 # 30MHz - 50MHz > > + - 2 # 50MHz - 75MHz > > + - 3 # 75MHz - 100MHz > > + - 4 # 100MHz - 130MHz > > + default: 3 > > + > > + # See ../video-interfaces.txt for details > > + port: > > + type: object > > + additionalProperties: false > > Should have a description of what data the port has. > It would be updated as below in next release. port: type: object additionalProperties: false description: Input port node, single endpoint describing the CSI-2 transmitter. > > + > > + properties: > > + endpoint: > > + type: object > > + additionalProperties: false > > + > > + properties: Actually I wonder whether we need to declare 'clock-lanes' here? > > + data-lanes: > > + maxItems: 1 > > + > > + link-frequencies: true > > + remote-endpoint: true > > + > > + required: Ditto. > > + - data-lanes > > + - link-frequencies > > + - remote-endpoint > > + > > + required: > > + - endpoint > > + > > +required: > > + - compatible > > + - reg > > + - clocks > > + - clock-names > > + - clock-frequency > > + - dovdd-supply > > + - avdd-supply > > + - dvdd-supply > > + - powerdown-gpios > > + - reset-gpios > > + - port > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + > > + #include <dt-bindings/clock/mt8183-clk.h> > > + #include <dt-bindings/gpio/gpio.h> > > + > > + i2c { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + ov02a10: camera-sensor@3d { > > + compatible = "ovti,ov02a10"; > > + reg = <0x3d>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&clk_24m_cam>; > > + > > + clocks = <&topckgen CLK_TOP_MUX_CAMTG>, > > + <&topckgen CLK_TOP_UNIVP_192M_D8>; > > + clock-names = "eclk", "freq_mux"; > > + clock-frequency = <24000000>; > > + > > + rotation = <180>; > > + ovti,mipi-tx-speed = <4>; > > + > > + dovdd-supply = <&mt6358_vcamio_reg>; > > + avdd-supply = <&mt6358_vcama1_reg>; > > + dvdd-supply = <&mt6358_vcn18_reg>; > > + > > + powerdown-gpios = <&pio 107 GPIO_ACTIVE_LOW>; > > + reset-gpios = <&pio 109 GPIO_ACTIVE_HIGH>; > > + > > + port { > > + wcam_out: endpoint { > > + data-lanes = <1>; > > + link-frequencies = /bits/ 64 <390000000>; > > + remote-endpoint = <&mipi_in_wcam>; > > + }; > > + }; > > + }; > > + }; > > + > > +... > > diff --git a/MAINTAINERS b/MAINTAINERS > > index e64e5db..63a2335 100644 > > --- a/MAINTAINERS > > +++ b/MAINTAINERS > > @@ -12389,6 +12389,13 @@ M: Harald Welte <laforge@xxxxxxxxxxxx> > > S: Maintained > > F: drivers/char/pcmcia/cm4040_cs.* > > > > +OMNIVISION OV02A10 SENSOR DRIVER > > +M: Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx> > > +L: linux-media@xxxxxxxxxxxxxxx > > +S: Maintained > > +T: git git://linuxtv.org/media_tree.git > > +F: Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml > > + > > OMNIVISION OV13858 SENSOR DRIVER > > M: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx> > > L: linux-media@xxxxxxxxxxxxxxx > > -- > > 2.9.2
