On 05/05/2020 16:58, Mauro Carvalho Chehab wrote: > Em Tue, 5 May 2020 14:21:38 +0200 > Hans Verkuil <hverkuil-cisco@xxxxxxxxx> escreveu: > >> On 05/05/2020 14:02, Mauro Carvalho Chehab wrote: >>> Em Fri, 17 Apr 2020 14:41:01 +0200 >>> Jacopo Mondi <jacopo@xxxxxxxxxx> escreveu: >>> >>>> Add documentation for the V4L2_CID_CAMERA_SENSOR_LOCATION camera >>>> control. The newly added read-only control reports the camera device >>>> mounting position. >>>> >>>> Signed-off-by: Jacopo Mondi <jacopo@xxxxxxxxxx> >>>> --- >>>> .../media/v4l/ext-ctrls-camera.rst | 32 +++++++++++++++++++ >>>> 1 file changed, 32 insertions(+) >>>> >>>> diff --git a/Documentation/userspace-api/media/v4l/ext-ctrls-camera.rst b/Documentation/userspace-api/media/v4l/ext-ctrls-camera.rst >>>> index e39f84d2447f..01a9042d53a6 100644 >>>> --- a/Documentation/userspace-api/media/v4l/ext-ctrls-camera.rst >>>> +++ b/Documentation/userspace-api/media/v4l/ext-ctrls-camera.rst >>>> @@ -510,6 +510,38 @@ enum v4l2_scene_mode - >>>> value down. A value of zero stops the motion if one is in progress >>>> and has no effect otherwise. >>>> >>>> +``V4L2_CID_CAMERA_SENSOR_LOCATION (integer)`` >>>> + This read-only control describes the camera sensor location by reporting >>>> + its mounting position on the device where the camera is installed. The >>>> + control value is constant and not modifiable by software. This control is >>>> + particularly meaningful for devices which have a well defined orientation, >>>> + such as phones, laptops and portable devices since the camera location is >>>> + expressed as a position relative to the device's intended usage orientation. >>>> + For example, a camera sensor installed on the user-facing side of a phone, >>>> + a tablet or a laptop device is said to be installed in the >>>> + ``V4L2_LOCATION_FRONT`` location while camera sensors installed on the side >>>> + opposite the front one are said to be installed in the >>>> + ``V4L2_LOCATION_BACK`` location. Camera sensors not directly attached to >>>> + the device or attached in a way that allows them to move freely, such as >>>> + webcams and digital cameras, are said to have the ``V4L2_LOCATION_EXTERNAL`` >>>> + location. >>>> + >>>> + >>>> + >>>> +.. flat-table:: >>>> + :header-rows: 0 >>>> + :stub-columns: 0 >>>> + >>>> + * - `` >>> `` >>>> + - The camera sensor is located on the front side of the device. >>>> + * - ``V4L2_LOCATION_BACK`` >>>> + - The camera sensor is located on the back side of the device. >>>> + * - ``V4L2_LOCATION_EXTERNAL`` >>>> + - The camera sensor is not directly attached to the device and is >>>> + freely movable. >>> >>> I guess I mentioned this already, but IMHO this ioctl is somewhat flawed, >>> for two reasons: >>> >>> 1) newer devices may all top of the line mobile devices now are coming >>> with multiple camera sensors at the same side. So, just saying that >>> the location is front or back is not enough. A location syscall would >>> need have something more to better identify the location. >>> It probably doesn't need to be something fancy, but, at least, on a >>> device with 3 back sensors, I would call them as: >>> >>> V4L2_LOCATION_BACK_1 >>> V4L2_LOCATION_BACK_2 >>> V4L2_LOCATION_BACK_3 >>> >>> And add some comment at the control documentation that would allow to >>> uniquely number the other ones, like: >>> >>> "when multiple sensors are present at the same side, sensors >>> will be numbered considering the ``(x,y)`` coordinates of the center >>> of each sensor, starting from the topmost, leftmost position. >>> >>> She first sensor will be the topmost sensor column at the leftmost >>> side. The other sensors that will have the same ``y`` coordinate, >>> counting from the left to the right, then increment the ``y`` and >>> parse the next column again until all sensors are numbered." >> >> I think this isn't a good idea. In most cases you do not care about this. > > True, because on most cases, the userspace is hardcoded to open, let's say, > video0 for the front sensor or video1 for the back sensor. > > This control only makes sense if the userspace is generic enough to accept > sensors on different positions, identifying them at runtime. > > With the current proposal, userspace can only work with 2 sensors, as, if > there's a third sensor, userspace won't know how to pick the right one. > > For instance, let's assume a car with 4 sensors, one on each side of > the car (right, front); (left, front); (right; back); (left; back). > > With the current proposal, userspace can't do anything if it wants > to identify the (right, back) camera. > >> And if you do care about this, then wouldn't it be better to do that through >> a new control where you provide the precise coordinates in e.g. mm? >> >> BACK_1/2/3 really doesn't tell you anything other than that there are three >> sensors on the back, but we knew that already. > > No, if we define some criteria about how sensors should be accounted for > (something similar to the text I drafted), the location will be defined. > > With the above text, for example, a device with 3 sensors horizontally > aligned, the arrangement will be: > > - sensor 1 is on the left; > - sensor 2 in the middle; > - sensor 3 is on the right. Or sensor 2 is below sensor 1 and sensor 3 is to the right of sensor 1. It's meaningless information. If you want to specify the location, then be precise. Especially for stereoscopic sensors (left and right) it is good to know the exact distance between the sensors. Just calling them '1' and '2' is not enough. For sensors you want to know the plane (back/front) and where they are on that plane (in the case of more than one sensor). That's separate information that's only needed in the case of more than one sensor. > > Ok, I agree that writing a text with such criteria sucks, and maybe > just numbering from 1 to n may not be the best thing to do. Yet, > adding coordinates in mm would be just too much information, IMHO. Why? Just numbering them makes no sense, it's useless information. > >> If we need support for the precise location in the future, then let's do that >> right and not try to shoehorn into something that wasn't meant for it. > > Assuming that all the problems we have so far are to support devices with > 2 sensors, by the time we add support for a third sensor, we'll end having > a new ioctl for the same thing: to specify the sensors locations. It's just a control, nothing more. In most cases all you need to know is if it is a front or back sensor. In some cases you need to know more: e.g. my Samsung Note 10+ has three sensors on the back in a vertical row (wide, telephoto, ultrawide), and two sensors for 3D to the right of them. For those last two you need to know the exact position relative to one another. For the other sensors all you need to know is that they are back sensors. > > We know the drill: having two controls for the same thing makes userspace > more complex and will require backward-compatibility code at the kernel > and at userspace. That's what I want to avoid. > > I'm open to other suggestions that won't limit the usage of this control > for devices with just (up to) two sensors. What backward compatibility code are you talking about? I honestly don't see the problem here. > >> >>> >>> 2) There are also some devices that has a movable sensor, that can either >>> be taking a picture from the front or from the back, like those: >>> >>> https://www.youtube.com/watch?v=br6G7MrkRUc >>> >>> On such case, the control should not be read-only, as one may need to >>> change this control in order to select if a sensor would either be on >>> FRONT or on BACK position. >>> >>> For such kind of sensors (when we start supporting them), we could >>> for example call them like: >>> >>> V4L2_LOCATION_MOVABLE_IN_BACK_POSITION_1 >>> V4L2_LOCATION_MOVABLE_IN_BACK_POSITION_2 >>> V4L2_LOCATION_MOVABLE_IN_FRONT_POSITION_1 >>> V4L2_LOCATION_MOVABLE_IN_FRONT_POSITION_2 >> >> I don't like this. If the driver can tell when the position changes, then it >> can update the control's value (it's still read-only because userspace >> can't write to it, but that doesn't mean it can't be updated). > > Why userspace can't set it? I mean, if the camera is movable, it > should be up to the application to select the sensor between FRONT > and BACK. Ah, right. If you can command the camera to flip from back to front using a button or something, then yes, it can be writable. Sorry, didn't think of that. I was thinking that the user would manually move the camera and the new position would be detected by the driver and reported in the location control. In any case, if the location control can be set through the driver by setting this control, then just drop the READ_ONLY flag. If the control is writable, then the sensor is movable. Just document this and we're done. You are making this much more complicated than it need to be IMHO. > > Btw, this is a case where I clearly see value on this ioctl: all cameras It's a *control*, not a new ioctl. > with flippable sensors need a control to switch the sensor's position, > even if the sensor device is hardcoded on some application. > >> So there is >> no need to call it 'MOVABLE', you just report the correct location. And with >> QUERYMENU you can tell that it is movable since multiple possible locations >> are reported (BACK and FRONT in this example). If it is fixed, then QUERYMENU >> will report only a single location. >> >> This might have some consequences for the DT bindings, though. Not sure >> how to represent this there. > > I guess DT should contain the default value when the device is turned > off. > >> If the driver cannot tell what the position is, then it makes no sense for >> the driver to expose this location control since it clearly is something that >> has to be hardcoded in userspace. I.e., there is no point for userspace to >> write to the control and then read back what it wrote :-) > > Actually there is. When you command a device to switch position, it may > take some time to move the sensor, and such operation may even fail. Yeah, I forgot about that option. > > So, reading back the position is probably mandatory. Well, it's a control, so that's standard. > > That reminds that it may actually have a third position, to warn > that the sensor was blocked. > > Also, some flip sensors may have another position (a "closed" > position). It's certainly possible that we need to add new positions to support the various states of such a movable sensor. But that's no problem. It's just a menu control, adding new positions is cheap and easy. I stand by what I said, except that I agree that this control can be writable in some circumstances, and that should be documented. I strongly disagree with the notion of BACK_1/2/3 and FRONT_1/2/3: it adds no meaningful information. If you have multiple sensors and in order to use them the application needs to know the relative positions (most likely for 3D sensors), then provide the precise position. The unit for that should probably be micrometer since millimeter is most likely not precise enough (at least looking at the depth sensors on my camera). Regards, Hans > >> So I disagree that there is a need for FIXED vs MOVABLE, this can be >> represented nicely with the current proposal. > > Thanks, > Mauro >
