Em Fri, 17 Apr 2020 14:41:01 +0200 Jacopo Mondi <jacopo@xxxxxxxxxx> escreveu: > Add documentation for the V4L2_CID_CAMERA_SENSOR_LOCATION camera > control. The newly added read-only control reports the camera device > mounting position. > > Signed-off-by: Jacopo Mondi <jacopo@xxxxxxxxxx> > --- > .../media/v4l/ext-ctrls-camera.rst | 32 +++++++++++++++++++ > 1 file changed, 32 insertions(+) > > diff --git a/Documentation/userspace-api/media/v4l/ext-ctrls-camera.rst b/Documentation/userspace-api/media/v4l/ext-ctrls-camera.rst > index e39f84d2447f..01a9042d53a6 100644 > --- a/Documentation/userspace-api/media/v4l/ext-ctrls-camera.rst > +++ b/Documentation/userspace-api/media/v4l/ext-ctrls-camera.rst > @@ -510,6 +510,38 @@ enum v4l2_scene_mode - > value down. A value of zero stops the motion if one is in progress > and has no effect otherwise. > > +``V4L2_CID_CAMERA_SENSOR_LOCATION (integer)`` > + This read-only control describes the camera sensor location by reporting > + its mounting position on the device where the camera is installed. The > + control value is constant and not modifiable by software. This control is > + particularly meaningful for devices which have a well defined orientation, > + such as phones, laptops and portable devices since the camera location is > + expressed as a position relative to the device's intended usage orientation. > + For example, a camera sensor installed on the user-facing side of a phone, > + a tablet or a laptop device is said to be installed in the > + ``V4L2_LOCATION_FRONT`` location while camera sensors installed on the side > + opposite the front one are said to be installed in the > + ``V4L2_LOCATION_BACK`` location. Camera sensors not directly attached to > + the device or attached in a way that allows them to move freely, such as > + webcams and digital cameras, are said to have the ``V4L2_LOCATION_EXTERNAL`` > + location. > + > + > + > +.. flat-table:: > + :header-rows: 0 > + :stub-columns: 0 > + > + * - `` `` > + - The camera sensor is located on the front side of the device. > + * - ``V4L2_LOCATION_BACK`` > + - The camera sensor is located on the back side of the device. > + * - ``V4L2_LOCATION_EXTERNAL`` > + - The camera sensor is not directly attached to the device and is > + freely movable. I guess I mentioned this already, but IMHO this ioctl is somewhat flawed, for two reasons: 1) newer devices may all top of the line mobile devices now are coming with multiple camera sensors at the same side. So, just saying that the location is front or back is not enough. A location syscall would need have something more to better identify the location. It probably doesn't need to be something fancy, but, at least, on a device with 3 back sensors, I would call them as: V4L2_LOCATION_BACK_1 V4L2_LOCATION_BACK_2 V4L2_LOCATION_BACK_3 And add some comment at the control documentation that would allow to uniquely number the other ones, like: "when multiple sensors are present at the same side, sensors will be numbered considering the ``(x,y)`` coordinates of the center of each sensor, starting from the topmost, leftmost position. She first sensor will be the topmost sensor column at the leftmost side. The other sensors that will have the same ``y`` coordinate, counting from the left to the right, then increment the ``y`` and parse the next column again until all sensors are numbered." 2) There are also some devices that has a movable sensor, that can either be taking a picture from the front or from the back, like those: https://www.youtube.com/watch?v=br6G7MrkRUc On such case, the control should not be read-only, as one may need to change this control in order to select if a sensor would either be on FRONT or on BACK position. For such kind of sensors (when we start supporting them), we could for example call them like: V4L2_LOCATION_MOVABLE_IN_BACK_POSITION_1 V4L2_LOCATION_MOVABLE_IN_BACK_POSITION_2 V4L2_LOCATION_MOVABLE_IN_FRONT_POSITION_1 V4L2_LOCATION_MOVABLE_IN_FRONT_POSITION_2 And add rename the other definitions to: V4L2_LOCATION_FIXED_FRONT_1 V4L2_LOCATION_FIXED_BACK_1 Ok, nobody has yet attempted to upstream code for such devices, so, we, for now, we don't need to add more than those 3 types. But, IMO, we would change the sensors description in a way that it would be easier to add support for more than one sensor per location in the future, like: * - ``V4L2_LOCATION_FIXED_FRONT_1`` - The camera sensor is fixed, being the first sensor located on the front side of the device. * - ``V4L2_LOCATION_FIXED_BACK_1`` - The camera sensor is fixed, being the first sensor located on the back side of the device. * - ``V4L2_LOCATION_EXTERNAL`` - The camera sensor is not directly attached to the device and is freely movable. .. note:: Please submit a patch upstream if you need to have more than one sensor either at front or back position. This would make a lot easier when someone upstream patches requiring to locate more than one sensor location, or to support flipping sensors. Thanks, Mauro
