Re: [PATCH v3 1/2] dt-bindings: Document MIPID02 bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Mickael,

On Tue, Mar 26, 2019 at 01:40:18PM +0000, Mickael GUENE wrote:
> Hi Sakari,
> 
> On 3/26/19 13:17, Sakari Ailus wrote:
> > Hi Mickael,
> > 
> > On Tue, Mar 26, 2019 at 11:03:39AM +0100, Mickael Guene wrote:
> >> This adds documentation of device tree for MIPID02 CSI-2 to PARALLEL
> >> bridge.
> >>
> >> Signed-off-by: Mickael Guene <mickael.guene@xxxxxx>
> >> ---
> >>
> >> Changes in v3: None
> >> Changes in v2:
> >> - Add precision about first CSI-2 port data rate
> >> - Document endpoints supported properties
> >> - Rename 'mipid02@14' into generic 'csi2rx@14' in example
> >>
> >>  .../bindings/media/i2c/st,st-mipid02.txt           | 83 ++++++++++++++++++++++
> >>  MAINTAINERS                                        |  7 ++
> >>  2 files changed, 90 insertions(+)
> >>  create mode 100644 Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt
> >>
> >> diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt
> >> new file mode 100644
> >> index 0000000..dfeab45
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt
> >> @@ -0,0 +1,83 @@
> >> +STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge
> >> +
> >> +MIPID02 has two CSI-2 input ports, only one of those ports can be active at a
> >> +time. Active port input stream will be de-serialized and its content outputted
> >> +through PARALLEL output port.
> >> +CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2 second
> >> +input port is a single lane 800Mbps. Both ports support clock and data lane
> >> +polarity swap. First port also supports data lane swap.
> >> +PARALLEL output port has a maximum width of 12 bits.
> >> +Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888, RGB444,
> >> +YUV420 8-bit, YUV422 8-bit and YUV420 10-bit.
> >> +
> >> +Required Properties:
> >> +- compatible: should be "st,st-mipid02"
> >> +- clocks: reference to the xclk input clock.
> >> +- clock-names: should be "xclk".
> >> +- VDDE-supply: sensor digital IO supply. Must be 1.8 volts.
> >> +- VDDIN-supply: sensor internal regulator supply. Must be 1.8 volts.
> >> +
> >> +Optional Properties:
> >> +- reset-gpios: reference to the GPIO connected to the xsdn pin, if any.
> >> +	       This is an active low signal to the mipid02.
> >> +
> >> +Required subnodes:
> >> +  - ports: A ports node with one port child node per device input and output
> >> +	   port, in accordance with the video interface bindings defined in
> >> +	   Documentation/devicetree/bindings/media/video-interfaces.txt. The
> >> +	   port nodes are numbered as follows:
> >> +
> >> +	   Port Description
> >> +	   -----------------------------
> >> +	   0    CSI-2 first input port
> >> +	   1    CSI-2 second input port
> >> +	   2    PARALLEL output
> >> +
> >> +Endpoint node optional properties for CSI-2 connection are:
> >> +- bus-type: if present should be 4 - MIPI CSI-2 D-PHY.
> > 
> > You can drop this IMO --- there's just a single valid value so the driver
> > may know that.
> > 
> ok
> >> +- clock-lanes: should be set to <0> if present (clock lane on hardware lane 0).
> > 
> > And please omit this, too, if the clock lane is always 0. Please update the
> > example, too. The driver doesn't need to check that either IMO, but up to
> > you.
> > 
> ok I will drop it from device tree documentation but I will keep driver check.
> I will also make data-lanes mandatory.
> >> +- data-lanes: if present should be <1> for Port 1. for Port 0 dual-lane
> >> +operation should be <1 2> or <2 1>. For Port 0 single-lane operation should be
> >> +<1> or <2>.
> >> +- lane-polarities: any lane can be inverted.
> >> +
> >> +Endpoint node optional properties for PARALLEL connection are:
> >> +- bus-type: if present should be 5 - Parallel.
> > 
> > This, too, can be omitted.
> > 
> ok
> >> +- bus-width: shall be set to <6>, <7>, <8>, <10> or <12>.
> >> +- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
> >> +- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
> > 
> > If these are optional, what are the defaults? IMO you could make them
> > mandatory as well.
> > 
> I will make bus-width mandatory
> hsync-active and vsync-active will stay optional with LOW being the default.

The above seems good to me. Thanks!

-- 
Sakari Ailus



[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux