This adds documentation of device tree for MIPID02 CSI-2 to PARALLEL
bridge.
Signed-off-by: Mickael Guene <mickael.guene@xxxxxx>
---
Changes in v3: None
Changes in v2:
- Add precision about first CSI-2 port data rate
- Document endpoints supported properties
- Rename 'mipid02@14' into generic 'csi2rx@14' in example
.../bindings/media/i2c/st,st-mipid02.txt | 83 ++++++++++++++++++++++
MAINTAINERS | 7 ++
2 files changed, 90 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt
diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt
new file mode 100644
index 0000000..dfeab45
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt
@@ -0,0 +1,83 @@
+STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge
+
+MIPID02 has two CSI-2 input ports, only one of those ports can be active at a
+time. Active port input stream will be de-serialized and its content outputted
+through PARALLEL output port.
+CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2 second
+input port is a single lane 800Mbps. Both ports support clock and data lane
+polarity swap. First port also supports data lane swap.
+PARALLEL output port has a maximum width of 12 bits.
+Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888, RGB444,
+YUV420 8-bit, YUV422 8-bit and YUV420 10-bit.
+
+Required Properties:
+- compatible: should be "st,st-mipid02"
+- clocks: reference to the xclk input clock.
+- clock-names: should be "xclk".
+- VDDE-supply: sensor digital IO supply. Must be 1.8 volts.
+- VDDIN-supply: sensor internal regulator supply. Must be 1.8 volts.
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the xsdn pin, if any.
+ This is an active low signal to the mipid02.
+
+Required subnodes:
+ - ports: A ports node with one port child node per device input and output
+ port, in accordance with the video interface bindings defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt. The
+ port nodes are numbered as follows:
+
+ Port Description
+ -----------------------------
+ 0 CSI-2 first input port
+ 1 CSI-2 second input port
+ 2 PARALLEL output
+
+Endpoint node optional properties for CSI-2 connection are:
+- bus-type: if present should be 4 - MIPI CSI-2 D-PHY.
+- clock-lanes: should be set to <0> if present (clock lane on hardware lane 0).
+- data-lanes: if present should be <1> for Port 1. for Port 0 dual-lane
+operation should be <1 2> or <2 1>. For Port 0 single-lane operation should be
+<1> or <2>.
+- lane-polarities: any lane can be inverted.
+
+Endpoint node optional properties for PARALLEL connection are:
+- bus-type: if present should be 5 - Parallel.
+- bus-width: shall be set to <6>, <7>, <8>, <10> or <12>.
+- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
+- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
+
+Example:
+
+mipid02: csi2rx@14 {
+ compatible = "st,st-mipid02";
+ reg = <0x14>;
+ status = "okay";
+ clocks = <&clk_ext_camera_12>;
+ clock-names = "xclk";
+ VDDE-supply = <&vdd>;
+ VDDIN-supply = <&vdd>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+
+ ep0: endpoint {
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ remote-endpoint = <&mipi_csi2_in>;
+ };
+ };
+ port@2 {
+ reg = <2>;
+
+ ep2: endpoint {
+ bus-width = <8>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ remote-endpoint = <¶llel_out>;
+ };
+ };
+ };
+};
diff --git a/MAINTAINERS b/MAINTAINERS
index e17ebf7..74da99d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14668,6 +14668,13 @@ S: Maintained
F: drivers/iio/imu/st_lsm6dsx/
F: Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt
+ST MIPID02 CSI-2 TO PARALLEL BRIDGE DRIVER
+M: Mickael Guene <mickael.guene@xxxxxx>
+L: linux-media@xxxxxxxxxxxxxxx
+T: git git://linuxtv.org/media_tree.git
+S: Maintained
+F: Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt
+
ST STM32 I2C/SMBUS DRIVER
M: Pierre-Yves MORDRET <pierre-yves.mordret@xxxxxx>
L: linux-i2c@xxxxxxxxxxxxxxx
--
2.7.4
