Hi,
Michael Trimarchi wrote:
Hi all,
Aguirre, Sergio wrote:
-----Original Message-----
From: Michael Trimarchi [mailto:michael@xxxxxxxxxxxxxxxxxxxxxxx]
Sent: Tuesday, January 12, 2010 7:15 AM
To: Aguirre, Sergio
Cc: Nishanth Menon; linux-omap@xxxxxxxxxxxxxxx; linux-
media@xxxxxxxxxxxxxxx
Subject: Re: ISP OMAP3 camera support ov7690
Hi all,
Now I have a good camera pcb and I can test again the driver. My
board is
an overo gumstix board.
Excellent!
Please let me know if you're having issues with it.
Thanks for your interest!
Regards,
Sergio
maybe I have done some mistake during writing the email, but I have
asked few things inside the email.
The camera part is ok because I have written a driver using the ov538
bridge but I have some problem
in configuring the isp omap3 device. It opens correctly the camera, and
set xclk frequency. Then
seems that vsync and hsync are not routed to the engine because I don't
receive any interrupt.
--- a/drivers/media/video/isp/isp.c
+++ b/drivers/media/video/isp/isp.c
@@ -299,6 +299,7 @@ static void isp_enable_interrupts(struct device *dev)
| IRQ0ENABLE_CSIA_IRQ
| IRQ0ENABLE_CSIB_IRQ | IRQ0ENABLE_HIST_DONE_IRQ
| IRQ0ENABLE_H3A_AWB_DONE_IRQ | IRQ0ENABLE_H3A_AF_DONE_IRQ
+ | IRQ0ENABLE_HS_VS_IRQ
| isp->interrupts;
if (CCDC_PREV_CAPTURE(isp))
@@ -328,6 +329,7 @@ static void isp_disable_interrupts(struct device *dev)
| IRQ0ENABLE_CSIA_IRQ
| IRQ0ENABLE_CSIB_IRQ | IRQ0ENABLE_HIST_DONE_IRQ
| IRQ0ENABLE_H3A_AWB_DONE_IRQ | IRQ0ENABLE_H3A_AF_DONE_IRQ
+ | IRQ0ENABLE_HS_VS_IRQ
| isp->interrupts);
Adding this in the irq mask give me interrupt from the camera, but I don't undestarstand
why they are disabled. Are they disabled in the latest git code?
how can I get the vrise?
.hsvs_syncdetect = ISPCTRL_SYNC_DETECT_VSFALL,
Michael
Aguirre Rodriguez, Sergio Alberto wrote:
Hi Michael,
-----Original Message-----
From: linux-omap-owner@xxxxxxxxxxxxxxx
[mailto:linux-omap-owner@xxxxxxxxxxxxxxx] On Behalf Of michael
Sent: Sunday, October 04, 2009 7:29 PM
To: Nishanth Menon
Cc: linux-omap@xxxxxxxxxxxxxxx; linux-media@xxxxxxxxxxxxxxx
Subject: Re: ISP OMAP3 camera support ov7690
Hi,
cc: linux-media
Nishanth Menon wrote:
michael said the following on 10/03/2009 06:13 PM:
I'm writing a driver to support the ov7690 camera and I have some
question about the meaning of:
- datalane configuration
CSI2 Data lanes - each CSI2 lane is a differential pair.
And, at least 1
clock and data lane is used in devices.
Sorry can you explain a little bit more. I have the camera
connected to the
cam_hs and cam_vs and the data is 8Bit. I use the the isp init
structure. The sccb bus works great and I can send
configuration to it,
but I don't receive any interrupt from the ics, seems that it
doen't see
the transaction:
The ISPCCDC: ###CCDC SYN_MODE=0x31704 seems ok.
static struct isp_interface_config ov7690_if_config = {
.ccdc_par_ser = ISP_CSIA,
.dataline_shift = 0x0,
.hsvs_syncdetect = ISPCTRL_SYNC_DETECT_VSFALL,
Can you try with ISPCTRL_SYNC_DETECT_VSRISE ?
.strobe = 0x0,
.prestrobe = 0x0,
.shutter = 0x0,
.wenlog = ISPCCDC_CFG_WENLOG_AND,
.wait_hs_vs = 0x4,
.raw_fmt_in = ISPCCDC_INPUT_FMT_GR_BG,
.u.csi.crc = 0x0,
.u.csi.mode = 0x0,
.u.csi.edge = 0x0,
.u.csi.signalling = 0x0,
.u.csi.strobe_clock_inv = 0x0,
.u.csi.vs_edge = 0x0,
.u.csi.channel = 0x0,
.u.csi.vpclk = 0x1,
.u.csi.data_start = 0x0,
.u.csi.data_size = 0x0,
.u.csi.format = V4L2_PIX_FMT_YUYV,
};
and I don't know the meaning of
lanecfg.clk.pol = OV7690_CSI2_CLOCK_POLARITY;
lanecfg.clk.pos = OV7690_CSI2_CLOCK_LANE;
lanecfg.data[0].pol = OV7690_CSI2_DATA0_POLARITY;
lanecfg.data[0].pos = OV7690_CSI2_DATA0_LANE;
lanecfg.data[1].pol = OV7690_CSI2_DATA1_POLARITY;
lanecfg.data[1].pos = OV7690_CSI2_DATA1_LANE;
lanecfg.data[2].pol = 0;
lanecfg.data[2].pos = 0;
lanecfg.data[3].pol = 0;
lanecfg.data[3].pos = 0;
This is the physical connection details:
- The .pol field stands for the differntial pair polarity.
(i.e. the order in which the negative and positive connections
are pugged in to the CSI2 ComplexIO module)
What exact the meaning of the pol, sorry? I have a signal that is
connected
to a pin. If the pos is avalaible can I use it?
It's not important how to route the signal but don't route on the same
lane.
Is it right?
This is the timing of the camera so I can check signal, but I don't
receive interrupt
of isp engine
The camera is direct connected to the
camera omap camera signal and using the oscilloscope I can see the hs/vs
signal
The hs is low and go up, like the vs signal. I have only one camera
with that use D0 to D7 data bit.
http://www.gumstix.net/Hardware/view/I/O-connectors-cabling/Gumstix-Overo-
27-pin-connector-J5-to-manage-camera-controls/112.html
static struct isp_interface_config ov7690_if_config = {
.ccdc_par_ser = ISP_CSIA,
.dataline_shift = 0x0,
.hsvs_syncdetect = ISPCTRL_SYNC_DETECT_VSRISE,
.strobe = 0x0,
.prestrobe = 0x0,
.shutter = 0x0,
.wenlog = ISPCCDC_CFG_WENLOG_AND,
.wait_hs_vs = 0x4,
.raw_fmt_in = ISPCCDC_INPUT_FMT_GR_BG,
.u.csi.crc = 0x0,
.u.csi.mode = 0x0,
.u.csi.edge = 0x0,
.u.csi.signalling = 0x0,
.u.csi.strobe_clock_inv = 0x0,
.u.csi.vs_edge = 0x0,
.u.csi.channel = 0x0,
.u.csi.vpclk = 0x1,
.u.csi.data_start = 0x0,
.u.csi.data_size = 0x0,
.u.csi.format = V4L2_PIX_FMT_YUYV,
};
This is my initial configuration
#define OV7690_CSI2_CLOCK_POLARITY 0 /* +/- pin order */
#define OV7690_CSI2_DATA0_POLARITY 0 /* +/- pin order */
#define OV7690_CSI2_DATA1_POLARITY 0 /* +/- pin order */
#define OV7690_CSI2_CLOCK_LANE 1 /* Clock lane
position: 1
*/
#define OV7690_CSI2_DATA0_LANE 2 /* Data0 lane
position: 2
*/
#define OV7690_CSI2_DATA1_LANE 3 /* Data1 lane
position: 3
*/
tim#define OV7690_CSI2_PHY_THS_TERM 2
#define OV7690_CSI2_PHY_THS_SETTLE 23
#define OV7690_CSI2_PHY_TCLK_TERM 0
#define OV7690_CSI2_PHY_TCLK_MISS 1
#define OV7690_CSI2_PHY_TCLK_SETTLE 14
With this clock polarity
lanecfg.clk.pol = OV7690_CSI2_CLOCK_POLARITY;
lanecfg.clk.pos = OV7690_CSI2_CLOCK_LANE;
lanecfg.data[0].pol = OV7690_CSI2_DATA0_POLARITY;
lanecfg.data[0].pos = OV7690_CSI2_DATA0_LANE;
lanecfg.data[1].pol = OV7690_CSI2_DATA1_POLARITY;
lanecfg.data[1].pos = OV7690_CSI2_DATA1_LANE;
lanecfg.data[2].pol = 0;
lanecfg.data[2].pos = 0;
lanecfg.data[3].pol = 0;
lanecfg.data[3].pos = 0;
isp_csi2_complexio_lanes_config(&isp->isp_csi2, &lanecfg);
Michael
--
Regards Michael
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
