Some news,
Hi hermann,
we are this results :
with
&tda827x_cfg_0, &tda827x_cfg_1 or &tda827x_cfg_2
we have a perfect image without sound on the analogic part (test with
mplayer),
a partial result with dvb-t : we need to initialize first with
analogic (with cold boot, the card doesn't work on dvb)
but only for few seconds(sound and image are ok) then re-initialize
with analogic, work for few seconds on dvb and then nothing
maybe i am wrong but, the sound part for analogic is a problem of
redirection, isn't it ?
fixed
here are our configuration for this card :
in saa7134-dvb.c
static struct tda1004x_config tda827x_flydvbtduo_medion_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP01_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x4b,
.tuner_address = 0x61,
.antenna_switch = 2,
.request_firmware = philips_tda1004x_request_firmware
};
case SAA7134_BOARD_FLYDVBTDUO_MEDION:
if (configure_tda827x_fe(dev, &tda827x_flydvbtduo_medion_config,
&tda827x_cfg_2) < 0)
goto dettach_frontend;
break;
default:
wprintk("Huh? unknown DVB card?\n");
break;
in saa7134-cards.c
[SAA7134_BOARD_FLYDVBTDUO_MEDION] = {
.name = "LifeView FlyDVB-T DUO Medion",
.audio_clock = 0x00187de7,
change with 0x00200000 and there is a perfect sound :)
.tuner_type = TUNER_PHILIPS_TDA8290,
.radio_type = UNSET,
.tuner_addr = ADDR_UNSET,
.radio_addr = ADDR_UNSET,
.gpiomask = 0x00200000,
.mpeg = SAA7134_MPEG_DVB,
.inputs = {{
.name = name_tv,
.vmux = 1,
.amux = TV,
.gpio = 0x200000, /* GPIO21=High for TV input */
.tv = 1,
},{
.name = name_comp1, /* Composite signal on S-Video input */
.vmux = 3,
.amux = LINE1,
},{
.name = name_svideo, /* S-Video signal on S-Video input */
.vmux = 8,
.amux = LINE1,
}},
.radio = {
.name = name_radio,
.amux = TV,
.gpio = 0x000000, /* GPIO21=Low for FM radio antenna */
},
.vendor = PCI_VENDOR_ID_PHILIPS,
.device = PCI_DEVICE_ID_PHILIPS_SAA7133,
.subvendor = 0x5168, .subdevice = 0x0307,
/* LR307-N */ .driver_data =
SAA7134_BOARD_FLYDVBTDUO_MEDION,
case SAA7134_BOARD_FLYDVBTDUO_MEDION:
{
/* this is a hybrid board, initialize to analog mode
* and configure firmware eeprom address
*/
u8 data[] = { 0x3c, 0x33, 0x60};
struct i2c_msg msg = {.addr=0x08, .flags=0, .buf=data, .len =
sizeof(data)};
i2c_transfer(&dev->i2c_adap, &msg, 1);
break;
What can we do to have dvb fully supported ?
Can someone point me in the right direction ?
thanks in advance,
Cheers,
Thomas
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
