Re: saa7134 (not very) new board 5168:0307

"tomlohave@xxxxxxxxx" <tomlohave@xxxxxxxxx> · Sat, 28 Nov 2009 11:55:44 +0100

hermann pitton a écrit :
Hi Tom,

Am Mittwoch, den 18.11.2009, 14:06 +0100 schrieb tomlohave@xxxxxxxxx:

Hello list,

looking from saa7134.h, this board  5168:0307  is not included
This cars is on some asus laptop and some medion laptop
It was previously working with this settings (1) card=55 tuner=54
or (2) with tuner = 86
ok, so with this settings, nothing :

with card = 55 :

[  109.375445] Linux video capture interface: v2.00
[  109.410546] saa7130/34: v4l2 driver version 0.2.14 loaded
[  109.410606] saa7133[0]: found at 0000:06:03.0, rev: 208, irq: 19, latency: 181, mmio: 0xb4007800
[  109.410614] saa7133[0]: subsystem: 5168:0307, board: LifeView FlyDVB-T DUO / MSI TV@nywhere Duo [card=55,insmod option]
[  109.410674] saa7133[0]: board init: gpio is 10000
[  109.410743] input: saa7134 IR (LifeView FlyDVB-T D as /devices/pci0000:00/0000:00:1e.0/0000:06:03.0/input/input9
[  109.587912] saa7133[0]: i2c eeprom 00: 68 51 07 03 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[  109.587924] saa7133[0]: i2c eeprom 10: 00 00 62 08 ff 20 ff ff ff ff ff ff ff ff ff ff
[  109.587934] saa7133[0]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 ff 01 e7 ff ff ff ff
[  109.587944] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[  109.587953] saa7133[0]: i2c eeprom 40: ff 24 00 c2 96 10 05 01 01 16 22 15 ff ff ff ff
[  109.587963] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[  109.587972] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[  109.587982] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[  109.587992] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[  109.588024] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[  109.588034] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[  109.588043] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[  109.588053] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[  109.588062] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[  109.588072] saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[  109.588081] saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[  109.596023] saa7133[0]: i2c scan: found device @ 0x10  [???]
[  109.612379] saa7133[0]: i2c scan: found device @ 0x96  [???]
[  109.620016] saa7133[0]: i2c scan: found device @ 0xa0  [eeprom]
[  109.984237] tuner' 0-004b: chip found @ 0x96 (saa7133[0])
[  110.064028] tda829x 0-004b: setting tuner address to 61
[  110.144024] tda829x 0-004b: type set to tda8290+75
[  114.804413] saa7133[0]: registered device video0 [v4l2]
[  114.804463] saa7133[0]: registered device vbi0
[  114.804509] saa7133[0]: registered device radio0
[  114.891645] saa7134 ALSA driver for DMA sound loaded
[  114.891706] saa7133[0]/alsa: saa7133[0] at 0xb4007800 irq 19 registered as card -2
[  115.705042] dvb_init() allocating 1 frontend
[  115.756244] DVB: registering new adapter (saa7133[0])
[  115.756254] DVB: registering adapter 0 frontend 0 (Philips TDA10046H DVB-T)...
[  115.940033] tda1004x: setting up plls for 48MHz sampling clock
[  116.106914] tda1004x: found firmware revision ff -- invalid
[  116.106921] tda1004x: trying to boot from eeprom
[  116.572024] tda1004x: found firmware revision 23 -- ok
[  117.016161] tda827x_probe_version: could not read from tuner at addr: 0xc0

[ 3969.562904] saa7130/34: v4l2 driver version 0.2.14 loaded
[ 3969.562994] saa7133[0]: found at 0000:06:03.0, rev: 208, irq: 19, latency: 181, mmio: 0xb4007800
[ 3969.563007] saa7133[0]: subsystem: 5168:0307, board: LifeView FlyDVB-T / Genius VideoWonder DVB-T [card=86,insmod option]
[ 3969.563091] saa7133[0]: board init: gpio is 10000
[ 3969.563219] input: saa7134 IR (LifeView FlyDVB-T / as /devices/pci0000:00/0000:00:1e.0/0000:06:03.0/input/input9
[ 3969.738045] saa7133[0]: i2c eeprom 00: 68 51 07 03 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[ 3969.738069] saa7133[0]: i2c eeprom 10: 00 00 62 08 ff 20 ff ff ff ff ff ff ff ff ff ff
[ 3969.738090] saa7133[0]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 ff 01 e7 ff ff ff ff
[ 3969.738111] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 3969.738132] saa7133[0]: i2c eeprom 40: ff 24 00 c2 96 10 05 01 01 16 22 15 ff ff ff ff
[ 3969.738152] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 3969.738173] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 3969.738194] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 3969.738214] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 3969.738235] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 3969.738256] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 3969.738276] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 3969.738297] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 3969.738318] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 3969.738338] saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 3969.738359] saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 3969.748030] saa7133[0]: i2c scan: found device @ 0x10  [???]
[ 3969.789056] saa7133[0]: i2c scan: found device @ 0x96  [???]
[ 3969.796023] saa7133[0]: i2c scan: found device @ 0xa0  [eeprom]
[ 3969.920245] tuner' 0-004b: chip found @ 0x96 (saa7133[0])
[ 3970.004029] tda829x 0-004b: setting tuner address to 61
[ 3970.084367] tda829x 0-004b: type set to tda8290+75
[ 3971.680487] saa7133[0]: registered device video0 [v4l2]
[ 3971.680538] saa7133[0]: registered device vbi0
[ 3971.808176] saa7134 ALSA driver for DMA sound loaded
[ 3971.808213] saa7133[0]/alsa: saa7133[0] at 0xb4007800 irq 19 registered as card -2
[ 3971.840321] dvb_init() allocating 1 frontend
[ 3971.880155] DVB: registering new adapter (saa7133[0])
[ 3971.880160] DVB: registering adapter 0 frontend 0 (Philips TDA10046H DVB-T)...
[ 3971.952041] tda1004x: setting up plls for 48MHz sampling clock
[ 3974.200031] tda1004x: timeout waiting for DSP ready
[ 3974.240038] tda1004x: found firmware revision 0 -- invalid
[ 3974.240044] tda1004x: trying to boot from eeprom
[ 3976.572028] tda1004x: timeout waiting for DSP ready
[ 3976.612115] tda1004x: found firmware revision 0 -- invalid
[ 3976.612121] tda1004x: waiting for firmware upload...
[ 3976.612129] saa7134 0000:06:03.0: firmware: requesting dvb-fe-tda10046.fw
[ 3989.140029] tda1004x: found firmware revision 20 -- ok
[ 3989.428167] tda827x_probe_version: could not read from tuner at addr: 0xc0
[ 4044.132025] tda1004x: setting up plls for 48MHz sampling clock
[ 4046.096030] tda1004x: found firmware revision 23 -- ok
[ 4046.368159] tda827x_probe_version: could not read from tuner at addr: 0xc0
[ 4049.464171] tda827x_probe_version: could not read from tuner at addr: 0xc0
[ 4061.800027] tda1004x: setting up plls for 48MHz sampling clock
[ 4063.764038] tda1004x: found firmware revision 23 -- ok
[ 4064.036167] tda827x_probe_version: could not read from tuner at addr: 0xc0
[ 4064.172178] tda827xo_set_params: could not write to tuner at addr: 0xc0
[ 4065.380178] tda827xo_set_params: could not write to tuner at addr: 0xc0
[ 4066.612273] tda827xo_set_params: could not write to tuner at addr: 0xc0
[ 4067.660166] tda827xo_set_params: could not write to tuner at addr: 0xc0
[ 4068.920158] tda827xo_set_params: could not write to tuner at addr: 0xc0
[ 4070.136168] tda827xo_set_params: could not write to tuner at addr: 0xc0
[ 4071.308169] tda827xo_set_params: could not write to tuner at addr: 0xc0
[ 4072.540174] tda827xo_set_params: could not write to tuner at addr: 0xc0
[ 4073.776186] tda827xo_set_params: could not write to tuner at addr: 0xc0
[ 4074.684166] tda827xo_set_params: could not write to tuner at addr: 0xc0
[ 4075.916169] tda827xo_set_params: could not write to tuner at addr: 0xc0
[ 4077.124179] tda827xo_set_params: could not write to tuner at addr: 0xc0
[ 4078.164246] tda827xo_set_params: could not write to tuner at addr: 0xc0
[ 4079.396166] tda827xo_set_params: could not write to tuner at addr: 0xc0
[ 4080.628168] tda827xo_set_params: could not write to tuner at addr: 0xc0
[ 4081.780174] tda827x_probe_version: could not read from tuner at addr: 0xc0
[ 4907.134088] saa7134 ALSA driver for DMA sound unloaded

ok

so i modified :
##################### saa7134.h

#define SAA7134_BOARD_FLYDVBTDUO_MEDION 176

##################### saa7134-dvb.c

case SAA7134_BOARD_FLYDVBTDUO_MEDION:
        if (configure_tda827x_fe(dev, &tda827x_flydvbtduo_medion_config,
                     &tda827x_cfg_0) < 0)
            goto dettach_frontend;
        break;

and

static struct tda1004x_config tda827x_flydvbtduo_medion_config = {
    .demod_address = 0x08,
    .invert        = 1,
    .invert_oclk   = 0,
    .xtal_freq     = TDA10046_XTAL_16M,
    .agc_config    = TDA10046_AGC_TDA827X,
    .gpio_config   = TDA10046_GP11_I,
    .if_freq       = TDA10046_FREQ_045,
    .tuner_address = 0x61,
    .request_firmware = philips_tda1004x_request_firmware

###################### saa7134-card.c

    [SAA7134_BOARD_FLYDVBTDUO_MEDION] = {
        .name           = "LifeView FlyDVB-T DUO Medion",
        .audio_clock    = 0x00187de7,
        .tuner_type     = TUNER_PHILIPS_TDA8290,
        .radio_type     = UNSET,
        .tuner_addr    = ADDR_UNSET,
        .radio_addr    = ADDR_UNSET,
/*        .gpiomask    = 0x00200000,*/
        .mpeg           = SAA7134_MPEG_DVB,
        .inputs         = {{
            .name = name_tv,
            .vmux = 1,
            .amux = TV,
/*            .gpio = 0x200000,    */ /* GPIO21=High for TV input */
            .tv   = 1,
        },{
            .name = name_comp1,    /* Composite signal on S-Video input */
            .vmux = 0,
            .amux = LINE2,
        },{
            .name = name_comp2,    /* Composite input */
            .vmux = 3,
            .amux = LINE2,
        },{
            .name = name_svideo,    /* S-Video signal on S-Video input */
            .vmux = 8,
            .amux = LINE2,
        }},
        .radio = {
            .name = name_radio,
            .amux = TV,
            .gpio = 0x000000,    /* GPIO21=Low for FM radio antenna */
        },
    },
};

and

        .vendor       = PCI_VENDOR_ID_PHILIPS,
        .device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
        .subvendor    = 0x5168,        
        .subdevice    = 0x0307,        
        .driver_data  = SAA7134_BOARD_FLYDVBTDUO_MEDION,

With tuner_address = 0x61, no error on log but no dvb

[   12.498255] saa7130/34: v4l2 driver version 0.2.15 loaded
[   12.498429] saa7134 0000:06:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[   12.498435] saa7133[0]: found at 0000:06:03.0, rev: 208, irq: 19, latency: 181, mmio: 0xb4007800
[   12.498443] saa7133[0]: subsystem: 5168:0307, board: LifeView FlyDVB-T DUO Medion [card=176,autodetected]
[   12.498516] saa7133[0]: board init: gpio is 10000
[   12.656021] saa7133[0]: i2c eeprom 00: 68 51 07 03 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[   12.656033] saa7133[0]: i2c eeprom 10: 00 00 62 08 ff 20 ff ff ff ff ff ff ff ff ff ff
[   12.656042] saa7133[0]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 ff 01 e7 ff ff ff ff
[   12.656052] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   12.656062] saa7133[0]: i2c eeprom 40: ff 24 00 c2 96 10 05 01 01 16 22 15 ff ff ff ff
[   12.656071] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   12.656081] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   12.656090] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   12.656100] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   12.656109] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   12.656119] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   12.656129] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   12.656138] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   12.656148] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   12.656157] saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   12.656167] saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   12.817084] tuner 0-004b: chip found @ 0x96 (saa7133[0])
[   12.896023] tda829x 0-004b: setting tuner address to 61
[   12.968053] tda829x 0-004b: type set to tda8290+75
[   17.692221] saa7133[0]: registered device video0 [v4l2]
[   17.692323] saa7133[0]: registered device vbi0
[   17.692439] saa7133[0]: registered device radio0
[   17.710523] saa7134 ALSA driver for DMA sound loaded
[   17.710556] saa7133[0]/alsa: saa7133[0] at 0xb4007800 irq 19 registered as card -2
[   17.784447] dvb_init() allocating 1 frontend
[   17.828176] DVB: registering new adapter (saa7133[0])
[   17.828182] DVB: registering adapter 0 frontend 0 (Philips TDA10046H DVB-T)...
[   17.900022] tda1004x: setting up plls for 48MHz sampling clock
[   20.148018] tda1004x: timeout waiting for DSP ready
[   20.188232] tda1004x: found firmware revision 0 -- invalid
[   20.188236] tda1004x: trying to boot from eeprom
[   22.516008] tda1004x: timeout waiting for DSP ready
[   22.556185] tda1004x: found firmware revision 0 -- invalid
[   22.556189] tda1004x: waiting for firmware upload...
[   22.556194] saa7134 0000:06:03.0: firmware: requesting dvb-fe-tda10046.fw
[   35.064055] tda1004x: found firmware revision 20 -- ok
[  223.588029] tda1004x: setting up plls for 48MHz sampling clock
[  225.552027] tda1004x: found firmware revision 23 -- ok
[  235.160031] tda1004x: setting up plls for 48MHz sampling clock
[  237.124041] tda1004x: found firmware revision 23 -- ok

any ideas, please ?

(1) http://www.linuxtv.org/pipermail/linux-dvb/2008-April/025786.html
(2) 
http://archives.devshed.com/forums/linux-97/flyduodvb-t-dvbscan-problem-2041600.html

just some note, helping further or not.

IIRC, nobody ever claimed to have DVB-T working on it.

It is listed in the m$ drivers as a DUO card, for LifeView at this time
it means for sure it has two tuners, but we don't have a trace to a
second tuner yet.

The other old DUO cards, PCI and cardbus, do find it.
A tda8274 at 0x60 for DVB-T and a first generation tda8275 for analog
TV.

In the current situation, I do suggest to physically inspect that Mini
PCI for the presence of two tuners and of course everything else you can
gather. Two eeproms? Firmware load looks inconsistent too and you should
try to provide a later revision, since it finally loads from host/file.

If you find, and you should, two different tuners physically, then this
is at least some ground to start further thinking about RF input
switching, i2c gates and such.

Cheers,
Hermann

Hi  Hermann,
thanks for informations ...
This card is not mine so physically inspect it is not possible and the 
owner is at 700 kms from me...
However, it seems there is only one hybrid tuner. The card is referenced as
AR307 rev N (seen on photos) and i found a link about this card :
http://www.pchub.com/uph/model/0--13652-1/LR307-parts.html

searching on LR307, i found a previous mail where you talked about a 
LR307- rev q
http://osdir.com/ml/linux-media/2009-09/msg00744.html

I modified a little the patch found in this mail (subvendor) and i have 
partial result :
- dvb tune work partially, not all channels are found
- dvb  channel in kaffeine works (image and sound) for few seconds and 
then nothing
- nothing for analogic stations

with others cards like 81,104,105 and 109, same results, kaffeine works 
and then hangs

What do you want to help this card to be supported ?

Thanks in advance

Cheers,

Thomas

--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html