Hi Steve,
I've done some more testing, and finally got MIPI capture work
properly on the i.MX6Q platform I'm testing on.
Apparently commit:
476dec012f4c6545b0b7599cd9adba2ed819ad3b
("media: ov5640: Add horizontal and vertical totals")
which several people, Jagan included, has reported introducing
regressions on MIPI actually breaks image capture.
I have a fix based on Maxime's and Sam's
[PATCH v3 01/12] media: ov5640: Fix timings setup code
I will send the two patches out soon.
If you and other people are eager to test them it would be awesome to
have a confirmation MIPI capture works for you too.
Thanks
j
On Tue, Jul 10, 2018 at 09:33:31AM +0200, jacopo mondi wrote:
> Hi Steve,
> thanks for testing!
>
> On Mon, Jul 09, 2018 at 02:52:09PM -0700, Steve Longerbeam wrote:
> > Hi Jacopo,
> >
> > I tested this patch on the i.MX6Q SabreSD with the OV5640 module.
> > It fixes the LP-11 timeout at stream on, but the captured images
> > are completely blank/black.
>
> Intersting that the module was not starting up properly on other
> (all?) i.MX6Q platforms, not only on Engicam's one. I didn't get this
> initially.
>
> Ok, so that's a step forward, but not enough probably. I'll keep
> looking into this and get back!
>
> Thanks
> j
>
> >
> > Steve
> >
> >
> > On 07/06/2018 04:00 AM, Jacopo Mondi wrote:
> > >From: Jacopo Mondi <jacopo@xxxxxxxxxx>
> > >
> > >Rework the MIPI interface startup sequence with the following changes:
> > >
> > >- Remove MIPI bus initialization from the initial settings blob
> > >- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in
> > > LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
> > >- At s_stream time enable/disable the MIPI interface output.
> > >- Restore default settings at set_power(0) time.
> > >
> > >Before this commit the sensor MIPI interface was initialized with settings
> > >that require a start/stop sequence at power-up time in order to force lanes
> > >into LP11 state, as they were initialized in LP00 when in 'sleep mode',
> > >which is assumed to be the sensor manual definition for the D-PHY defined
> > >stop mode.
> > >
> > >The stream start/stop was performed by enabling disabling clock gating,
> > >and had the side effect to change the lanes sleep mode configuration when
> > >stream was stopped.
> > >
> > >Clock gating/ungating:
> > >- ret = ov5640_mod_reg(sensor, OV5640_REG_MIPI_CTRL00, BIT(5),
> > >- on ? 0 : BIT(5));
> > >- if (ret)
> > >
> > >Set lanes in LP11 when in 'sleep mode':
> > >- ret = ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT00,
> > >- on ? 0x00 : 0x70);
> > >
> > >This commit fixes an issue reported by Jagan Teki on i.MX6 platforms that
> > >prevents the host interface from powering up correctly:
> > >https://lkml.org/lkml/2018/6/1/38
> > >
> > >It also improves MIPI capture operations stability on my testing platform
> > >where MIPI capture often (silently) failed and returned all-purple frames.
> > >
> > >fixes: f22996db44e2 ("media: ov5640: add support of DVP parallel interface")
> > >Reported-by: Jagan Teki <jagan@xxxxxxxxxxxxxxxxxxxx>
> > >Signed-off-by: Jacopo Mondi <jacopo@xxxxxxxxxx>
> > >
> > >---
> > >
> > >Hello,
> > > I'm sending this one as new patch instead of a v2 of the previously sent
> > >series "media: i2c: ov5640: Re-work MIPI interface configuration" as the
> > >previous one was not working on the Engicam i.Mx6 platform where Jagan
> > >initially reported issues on.
> > >
> > >I've been able to test that capture now starts on said platform, but I've not
> > >been able to visually verify any of the image content as I have no way yet to
> > >transfer the raw images to my development host and verify their content (network
> > >still not working for me on that platform :/ )
> > >
> > >On my other testing platform images are correct, but they already were with the
> > >previous version of this patches too, so I assume the CSI-2 receiver is far more
> > >tolerant there.
> > >
> > >Jagan, is there any way you could verify images? I would appreciate your
> > >Tested-by tag in case they're correct.
> > >
> > >Also, as there seems to be a lot of people interested in ov5640 these days, I
> > >have expanded the receivers list. Anyone that could give these patches a spin?
> > >(ie. Sam reported issues too with the current MIPI startup sequence in a patch
> > >series he shared on dropbox iirc...)
> > >
> > >Thanks
> > > j
> > >---
> > > drivers/media/i2c/ov5640.c | 91 ++++++++++++++++++++++++++++++++++++----------
> > > 1 file changed, 71 insertions(+), 20 deletions(-)
> > >
> > >diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c
> > >index 1ecbb7a..7bbd1d7 100644
> > >--- a/drivers/media/i2c/ov5640.c
> > >+++ b/drivers/media/i2c/ov5640.c
> > >@@ -286,10 +286,10 @@ static const struct reg_value ov5640_init_setting_30fps_VGA[] = {
> > > {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
> > > {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x3000, 0x00, 0, 0},
> > > {0x3002, 0x1c, 0, 0}, {0x3004, 0xff, 0, 0}, {0x3006, 0xc3, 0, 0},
> > >- {0x300e, 0x45, 0, 0}, {0x302e, 0x08, 0, 0}, {0x4300, 0x3f, 0, 0},
> > >+ {0x302e, 0x08, 0, 0}, {0x4300, 0x3f, 0, 0},
> > > {0x501f, 0x00, 0, 0}, {0x4713, 0x03, 0, 0}, {0x4407, 0x04, 0, 0},
> > > {0x440e, 0x00, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
> > >- {0x4837, 0x0a, 0, 0}, {0x4800, 0x04, 0, 0}, {0x3824, 0x02, 0, 0},
> > >+ {0x4837, 0x0a, 0, 0}, {0x3824, 0x02, 0, 0},
> > > {0x5000, 0xa7, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x5180, 0xff, 0, 0},
> > > {0x5181, 0xf2, 0, 0}, {0x5182, 0x00, 0, 0}, {0x5183, 0x14, 0, 0},
> > > {0x5184, 0x25, 0, 0}, {0x5185, 0x24, 0, 0}, {0x5186, 0x09, 0, 0},
> > >@@ -1102,12 +1102,18 @@ static int ov5640_set_stream_mipi(struct ov5640_dev *sensor, bool on)
> > > {
> > > int ret;
> > >
> > >- ret = ov5640_mod_reg(sensor, OV5640_REG_MIPI_CTRL00, BIT(5),
> > >- on ? 0 : BIT(5));
> > >- if (ret)
> > >- return ret;
> > >- ret = ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT00,
> > >- on ? 0x00 : 0x70);
> > >+ /*
> > >+ * Enable/disable the MIPI interface
> > >+ *
> > >+ * 0x300e = on ? 0x45 : 0x40
> > >+ * [7:5] = 001 : 2 data lanes mode
> > >+ * [4] = 0 : Power up MIPI HS Tx
> > >+ * [3] = 0 : Power up MIPI LS Rx
> > >+ * [2] = 1/0 : MIPI interface enable/disable
> > >+ * [1:0] = 01/00: FIXME: 'debug'
> > >+ */
> > >+ ret = ov5640_write_reg(sensor, OV5640_REG_IO_MIPI_CTRL00,
> > >+ on ? 0x45 : 0x40);
> > > if (ret)
> > > return ret;
> > >
> > >@@ -1786,23 +1792,68 @@ static int ov5640_set_power(struct ov5640_dev *sensor, bool on)
> > > if (ret)
> > > goto power_off;
> > >
> > >+ /* We're done here for DVP bus, while CSI-2 needs setup. */
> > >+ if (sensor->ep.bus_type != V4L2_MBUS_CSI2)
> > >+ return 0;
> > >+
> > >+ /*
> > >+ * Power up MIPI HS Tx and LS Rx; 2 data lanes mode
> > >+ *
> > >+ * 0x300e = 0x40
> > >+ * [7:5] = 001 : 2 data lanes mode
> > >+ * [4] = 0 : Power up MIPI HS Tx
> > >+ * [3] = 0 : Power up MIPI LS Rx
> > >+ * [2] = 0 : MIPI interface disabled
> > >+ */
> > >+ ret = ov5640_write_reg(sensor,
> > >+ OV5640_REG_IO_MIPI_CTRL00, 0x40);
> > >+ if (ret)
> > >+ goto power_off;
> > >+
> > >+ /*
> > >+ * Gate clock and set LP11 in 'no packets mode' (idle)
> > >+ *
> > >+ * 0x4800 = 0x24
> > >+ * [5] = 1 : Gate clock when 'no packets'
> > >+ * [2] = 1 : MIPI bus in LP11 when 'no packets'
> > >+ */
> > >+ ret = ov5640_write_reg(sensor,
> > >+ OV5640_REG_MIPI_CTRL00, 0x24);
> > >+ if (ret)
> > >+ goto power_off;
> > >+
> > >+ /*
> > >+ * Set data lanes and clock in LP11 when 'sleeping'
> > >+ *
> > >+ * 0x3019 = 0x70
> > >+ * [6] = 1 : MIPI data lane 2 in LP11 when 'sleeping'
> > >+ * [5] = 1 : MIPI data lane 1 in LP11 when 'sleeping'
> > >+ * [4] = 1 : MIPI clock lane in LP11 when 'sleeping'
> > >+ */
> > >+ ret = ov5640_write_reg(sensor,
> > >+ OV5640_REG_PAD_OUTPUT00, 0x70);
> > >+ if (ret)
> > >+ goto power_off;
> > >+
> > >+ /* Give lanes some time to coax into LP11 state. */
> > >+ usleep_range(500, 1000);
> > >+
> > >+ } else {
> > > if (sensor->ep.bus_type == V4L2_MBUS_CSI2) {
> > >- /*
> > >- * start streaming briefly followed by stream off in
> > >- * order to coax the clock lane into LP-11 state.
> > >- */
> > >- ret = ov5640_set_stream_mipi(sensor, true);
> > >- if (ret)
> > >- goto power_off;
> > >- usleep_range(1000, 2000);
> > >- ret = ov5640_set_stream_mipi(sensor, false);
> > >- if (ret)
> > >- goto power_off;
> > >+ /* Reset MIPI bus settings to their default values. */
> > >+ ov5640_write_reg(sensor,
> > >+ OV5640_REG_IO_MIPI_CTRL00, 0x58);
> > >+ ov5640_write_reg(sensor,
> > >+ OV5640_REG_MIPI_CTRL00, 0x04);
> > >+ ov5640_write_reg(sensor,
> > >+ OV5640_REG_PAD_OUTPUT00, 0x00);
> > > }
> > >
> > >- return 0;
> > >+ ov5640_set_power_off(sensor);
> > > }
> > >
> > >+ return 0;
> > >+
> > > power_off:
> > > ov5640_set_power_off(sensor);
> > > return ret;
> > >--
> > >2.7.4
> > >
> >
Attachment:
signature.asc
Description: PGP signature
