> -----Original Message----- > From: Hans Verkuil [mailto:hverkuil@xxxxxxxxx] > Sent: Monday, November 09, 2009 6:10 PM > To: Hiremath, Vaibhav > Cc: linux-media@xxxxxxxxxxxxxxx; Jadav, Brijesh R; Karicheri, > Muralidharan > Subject: Re: [PATCH 6/6] TVP514x:Switch to automode for > s_input/querystd > > Hi Vaibhav, > > See the review comments below. > > On Tuesday 13 October 2009 17:12:59 hvaibhav@xxxxxx wrote: > > From: Vaibhav Hiremath <hvaibhav@xxxxxx> > > > > Driver should switch to AutoSwitch mode on S_INPUT and QUERYSTD > ioctls. > > It has been observed that, if user configure the standard > explicitely > > then driver preserves the old settings. > > > > Reviewed by: Vaibhav Hiremath <hvaibhav@xxxxxx> > > Signed-off-by: Brijesh Jadav <brijesh.j@xxxxxx> > > --- > > drivers/media/video/tvp514x.c | 17 +++++++++++++++++ > > 1 files changed, 17 insertions(+), 0 deletions(-) > > > > diff --git a/drivers/media/video/tvp514x.c > b/drivers/media/video/tvp514x.c > > index 2443726..0b0412d 100644 > > --- a/drivers/media/video/tvp514x.c > > +++ b/drivers/media/video/tvp514x.c > > @@ -523,10 +523,18 @@ static int tvp514x_querystd(struct > v4l2_subdev *sd, v4l2_std_id *std_id) > > enum tvp514x_std current_std; > > enum tvp514x_input input_sel; > > u8 sync_lock_status, lock_mask; > > + int err; > > > > if (std_id == NULL) > > return -EINVAL; > > > > + err = tvp514x_write_reg(sd, REG_VIDEO_STD, > > + VIDEO_STD_AUTO_SWITCH_BIT); > > + if (err < 0) > > + return err; > > + > > + msleep(LOCK_RETRY_DELAY); > > + > > We have a problem here with the V4L2 spec. > > The spec says that the standard should not change unless set > explicitly by > the user. So switching to auto mode in querystd is not correct. > [Hiremath, Vaibhav] Hans, I have added this considering that; querystd means auto-detection of standard. V4L2 spec says that, Sense the video standard received by the current input. When user explicitly calls querystd, don't you think user should be aware of the fact that, driver is going to detect the standard automatically under this call. > Is it possible to detect the standard without switching to automode? > If it is, > then that's the preferred solution. > [Hiremath, Vaibhav] We can detect based on the TVP_VIDEO_STD_STATUS register, but will not be auto-detection. We will be reading the standard set by previous ioctls. > If it cannot be done, then we need to extend the API and add support > for a > proper way of enabling automode. > > This is actually a long standing issue that used to be pretty low > prio since > it is very rare to see 'spontaneous' switches from e.g. PAL to NTSC. > > But with the upcoming timings API for HDTV this will become much > more common. > (e.g. switching from 1080p to 720p). > > We need to define this quite carefully. In particular what will > happen if the > standard switches while streaming. How does that relate to a scaler > setup with > S_FMT? Do we know when this happens so that we can notify the > application? [Hiremath, Vaibhav] At-least in TVP5146 we have interrupt which we can enable on standard change from user on current input, but we are not using it. This could be another interesting point, how to add such support. > Can we lock the standard when starting capturing? [Hiremath, Vaibhav] I think this makes sense to me, we should not allow changing the standard once streaming is going on. I think event manager may play a major role here, on standard change we should be able to send event back to application. Now the question is how application is going to handle this, since currently there is not way application can specify AUTOMODE, he has to query the standard and set it again. Thanks, Vaibhav > > My gut feeling is that AUTO detect should only be allowed if the > application > can be notified when the standard changes, or if the standard can be > locked > when streaming starts. > > The second part that is needed is some way to set the receiver into > auto > switching mode. For SDTV that probably means adding a new AUTO > standard bit. > Although to be honest I'm not keen on having to add something to > v4l2_std_id. > > For the HDTV timings API we probably need to add an AUTO preset. > > Murali, can you think about this a bit and see how that will work > out? > > > /* get the current standard */ > > current_std = tvp514x_get_current_std(sd); > > if (current_std == STD_INVALID) > > @@ -643,6 +651,15 @@ static int tvp514x_s_routing(struct > v4l2_subdev *sd, > > /* Index out of bound */ > > return -EINVAL; > > > > + /* Since this api is goint to detect the input, it is required > > + to set the standard in the auto switch mode */ > > + err = tvp514x_write_reg(sd, REG_VIDEO_STD, > > + VIDEO_STD_AUTO_SWITCH_BIT); > > Huh? I don't see what s_routing has to do with auto switch mode. > > > + if (err < 0) > > + return err; > > + > > + msleep(LOCK_RETRY_DELAY); > > + > > input_sel = input; > > output_sel = output; > > > > -- > > 1.6.2.4 > > > > Regards, > > Hans > > > -- > Hans Verkuil - video4linux developer - sponsored by TANDBERG Telecom -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
