Re: [PATCH 1/2] platform: Add Amlogic Meson AO CEC Controller driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 07/06/2017 12:55 PM, Hans Verkuil wrote:
> On 07/06/17 12:27, Neil Armstrong wrote:
>> The Amlogic SoC embeds a standalone CEC controller, this patch adds a driver
>> for such controller.
>> The controller does not need HPD to be active, and could support up to max
>> 5 logical addresses, but only 1 is handled since the Suspend firmware can
>> make use of this unique logical address to wake up the device.
>>
>> The Suspend firmware configuration will be added in an other patchset.
>>
>> Signed-off-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx>
>> ---
>>  drivers/media/platform/Kconfig        |  11 +
>>  drivers/media/platform/Makefile       |   2 +
>>  drivers/media/platform/meson/Makefile |   1 +
>>  drivers/media/platform/meson/ao-cec.c | 653 ++++++++++++++++++++++++++++++++++
>>  4 files changed, 667 insertions(+)
>>  create mode 100644 drivers/media/platform/meson/Makefile
>>  create mode 100644 drivers/media/platform/meson/ao-cec.c
>>
>> diff --git a/drivers/media/platform/Kconfig b/drivers/media/platform/Kconfig
>> index 1313cd5..1e67381 100644
>> --- a/drivers/media/platform/Kconfig
>> +++ b/drivers/media/platform/Kconfig
>> @@ -536,6 +536,17 @@ menuconfig CEC_PLATFORM_DRIVERS
>>  
>>  if CEC_PLATFORM_DRIVERS
>>  
>> +config VIDEO_MESON_AO_CEC
>> +	tristate "Amlogic Meson AO CEC driver"
>> +	depends on ARCH_MESON || COMPILE_TEST
>> +	select CEC_CORE
>> +	select CEC_NOTIFIER
>> +	---help---
>> +	  This is a driver for Amlogic Meson SoCs AO CEC interface. It uses the
>> +	  generic CEC framework interface.
>> +	  CEC bus is present in the HDMI connector and enables communication
>> +	  between compatible devices.
>> +
>>  config VIDEO_SAMSUNG_S5P_CEC
>>         tristate "Samsung S5P CEC driver"
>>         depends on PLAT_S5P || ARCH_EXYNOS || COMPILE_TEST
>> diff --git a/drivers/media/platform/Makefile b/drivers/media/platform/Makefile
>> index 9beadc7..a52d7b6 100644
>> --- a/drivers/media/platform/Makefile
>> +++ b/drivers/media/platform/Makefile
>> @@ -86,3 +86,5 @@ obj-$(CONFIG_VIDEO_MEDIATEK_MDP)	+= mtk-mdp/
>>  obj-$(CONFIG_VIDEO_MEDIATEK_JPEG)	+= mtk-jpeg/
>>  
>>  obj-$(CONFIG_VIDEO_QCOM_VENUS)		+= qcom/venus/
>> +
>> +obj-y					+= meson/
>> diff --git a/drivers/media/platform/meson/Makefile b/drivers/media/platform/meson/Makefile
>> new file mode 100644
>> index 0000000..597beb8
>> --- /dev/null
>> +++ b/drivers/media/platform/meson/Makefile
>> @@ -0,0 +1 @@
>> +obj-$(CONFIG_VIDEO_MESON_AO_CEC)	+= ao-cec.o
>> diff --git a/drivers/media/platform/meson/ao-cec.c b/drivers/media/platform/meson/ao-cec.c
>> new file mode 100644
>> index 0000000..26d7c3e8
>> --- /dev/null
>> +++ b/drivers/media/platform/meson/ao-cec.c
>> @@ -0,0 +1,653 @@
>> +/*
>> + * Driver for Amlogic Meson AO CEC Controller
>> + *
>> + * Copyright (C) 2015 Amlogic, Inc. All rights reserved
>> + * Copyright (C) 2017 BayLibre, SAS
>> + * Author: Neil Armstrong <narmstrong@xxxxxxxxxxxx>
>> + *
>> + * SPDX-License-Identifier: GPL-2.0+
>> + */
>> +
>> +#include <linux/bitfield.h>
>> +#include <linux/clk.h>
>> +#include <linux/device.h>
>> +#include <linux/io.h>
>> +#include <linux/delay.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_platform.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/types.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/reset.h>
>> +#include <media/cec.h>
>> +#include <media/cec-notifier.h>
>> +
>> +/* CEC Registers */
>> +
>> +/*
>> + * [2:1] cntl_clk
>> + *  - 0 = Disable clk (Power-off mode)
>> + *  - 1 = Enable gated clock (Normal mode)
>> + *  - 2 = Enable free-run clk (Debug mode)
>> + */
>> +#define CEC_GEN_CNTL_REG		0x00
>> +
>> +#define CEC_GEN_CNTL_RESET		BIT(0)
>> +#define CEC_GEN_CNTL_CLK_DISABLE	0
>> +#define CEC_GEN_CNTL_CLK_ENABLE		1
>> +#define CEC_GEN_CNTL_CLK_ENABLE_DBG	2
>> +#define CEC_GEN_CNTL_CLK_CTRL_MASK	GENMASK(2, 1)
>> +
>> +/*
>> + * [7:0] cec_reg_addr
>> + * [15:8] cec_reg_wrdata
>> + * [16] cec_reg_wr
>> + *  - 0 = Read
>> + *  - 1 = Write
>> + * [23] bus free
>> + * [31:24] cec_reg_rddata
>> + */
>> +#define CEC_RW_REG			0x04
>> +
>> +#define CEC_RW_ADDR			GENMASK(7, 0)
>> +#define CEC_RW_WR_DATA			GENMASK(15, 8)
>> +#define CEC_RW_WRITE_EN			BIT(16)
>> +#define CEC_RW_BUS_BUSY			BIT(23)
>> +#define CEC_RW_RD_DATA			GENMASK(31, 24)
>> +
>> +/*
>> + * [1] tx intr
>> + * [2] rx intr
>> + */
>> +#define CEC_INTR_MASKN_REG		0x08
>> +#define CEC_INTR_CLR_REG		0x0c
>> +#define CEC_INTR_STAT_REG		0x10
>> +
>> +#define CEC_INTR_TX			BIT(1)
>> +#define CEC_INTR_RX			BIT(2)
>> +
>> +/* CEC Commands */
>> +
>> +#define CEC_TX_MSG_0_HEADER		0x00
>> +#define CEC_TX_MSG_1_OPCODE		0x01
>> +#define CEC_TX_MSG_2_OP1		0x02
>> +#define CEC_TX_MSG_3_OP2		0x03
>> +#define CEC_TX_MSG_4_OP3		0x04
>> +#define CEC_TX_MSG_5_OP4		0x05
>> +#define CEC_TX_MSG_6_OP5		0x06
>> +#define CEC_TX_MSG_7_OP6		0x07
>> +#define CEC_TX_MSG_8_OP7		0x08
>> +#define CEC_TX_MSG_9_OP8		0x09
>> +#define CEC_TX_MSG_A_OP9		0x0A
>> +#define CEC_TX_MSG_B_OP10		0x0B
>> +#define CEC_TX_MSG_C_OP11		0x0C
>> +#define CEC_TX_MSG_D_OP12		0x0D
>> +#define CEC_TX_MSG_E_OP13		0x0E
>> +#define CEC_TX_MSG_F_OP14		0x0F
>> +#define CEC_TX_MSG_LENGTH		0x10
>> +#define CEC_TX_MSG_CMD			0x11
>> +#define CEC_TX_WRITE_BUF		0x12
>> +#define CEC_TX_CLEAR_BUF		0x13
>> +#define CEC_RX_MSG_CMD			0x14
>> +#define CEC_RX_CLEAR_BUF		0x15
>> +#define CEC_LOGICAL_ADDR0		0x16
>> +#define CEC_LOGICAL_ADDR1		0x17
>> +#define CEC_LOGICAL_ADDR2		0x18
>> +#define CEC_LOGICAL_ADDR3		0x19
>> +#define CEC_LOGICAL_ADDR4		0x1A
>> +#define CEC_CLOCK_DIV_H			0x1B
>> +#define CEC_CLOCK_DIV_L			0x1C
>> +#define CEC_QUIESCENT_25MS_BIT7_0	0x20
>> +#define CEC_QUIESCENT_25MS_BIT11_8	0x21
>> +#define CEC_STARTBITMINL2H_3MS5_BIT7_0	0x22
>> +#define CEC_STARTBITMINL2H_3MS5_BIT8	0x23
>> +#define CEC_STARTBITMAXL2H_3MS9_BIT7_0	0x24
>> +#define CEC_STARTBITMAXL2H_3MS9_BIT8	0x25
>> +#define CEC_STARTBITMINH_0MS6_BIT7_0	0x26
>> +#define CEC_STARTBITMINH_0MS6_BIT8	0x27
>> +#define CEC_STARTBITMAXH_1MS0_BIT7_0	0x28
>> +#define CEC_STARTBITMAXH_1MS0_BIT8	0x29
>> +#define CEC_STARTBITMINTOT_4MS3_BIT7_0	0x2A
>> +#define CEC_STARTBITMINTOT_4MS3_BIT9_8	0x2B
>> +#define CEC_STARTBITMAXTOT_4MS7_BIT7_0	0x2C
>> +#define CEC_STARTBITMAXTOT_4MS7_BIT9_8	0x2D
>> +#define CEC_LOGIC1MINL2H_0MS4_BIT7_0	0x2E
>> +#define CEC_LOGIC1MINL2H_0MS4_BIT8	0x2F
>> +#define CEC_LOGIC1MAXL2H_0MS8_BIT7_0	0x30
>> +#define CEC_LOGIC1MAXL2H_0MS8_BIT8	0x31
>> +#define CEC_LOGIC0MINL2H_1MS3_BIT7_0	0x32
>> +#define CEC_LOGIC0MINL2H_1MS3_BIT8	0x33
>> +#define CEC_LOGIC0MAXL2H_1MS7_BIT7_0	0x34
>> +#define CEC_LOGIC0MAXL2H_1MS7_BIT8	0x35
>> +#define CEC_LOGICMINTOTAL_2MS05_BIT7_0	0x36
>> +#define CEC_LOGICMINTOTAL_2MS05_BIT9_8	0x37
>> +#define CEC_LOGICMAXHIGH_2MS8_BIT7_0	0x38
>> +#define CEC_LOGICMAXHIGH_2MS8_BIT8	0x39
>> +#define CEC_LOGICERRLOW_3MS4_BIT7_0	0x3A
>> +#define CEC_LOGICERRLOW_3MS4_BIT8	0x3B
>> +#define CEC_NOMSMPPOINT_1MS05		0x3C
>> +#define CEC_DELCNTR_LOGICERR		0x3E
>> +#define CEC_TXTIME_17MS_BIT7_0		0x40
>> +#define CEC_TXTIME_17MS_BIT10_8		0x41
>> +#define CEC_TXTIME_2BIT_BIT7_0		0x42
>> +#define CEC_TXTIME_2BIT_BIT10_8		0x43
>> +#define CEC_TXTIME_4BIT_BIT7_0		0x44
>> +#define CEC_TXTIME_4BIT_BIT10_8		0x45
>> +#define CEC_STARTBITNOML2H_3MS7_BIT7_0	0x46
>> +#define CEC_STARTBITNOML2H_3MS7_BIT8	0x47
>> +#define CEC_STARTBITNOMH_0MS8_BIT7_0	0x48
>> +#define CEC_STARTBITNOMH_0MS8_BIT8	0x49
>> +#define CEC_LOGIC1NOML2H_0MS6_BIT7_0	0x4A
>> +#define CEC_LOGIC1NOML2H_0MS6_BIT8	0x4B
>> +#define CEC_LOGIC0NOML2H_1MS5_BIT7_0	0x4C
>> +#define CEC_LOGIC0NOML2H_1MS5_BIT8	0x4D
>> +#define CEC_LOGIC1NOMH_1MS8_BIT7_0	0x4E
>> +#define CEC_LOGIC1NOMH_1MS8_BIT8	0x4F
>> +#define CEC_LOGIC0NOMH_0MS9_BIT7_0	0x50
>> +#define CEC_LOGIC0NOMH_0MS9_BIT8	0x51
>> +#define CEC_LOGICERRLOW_3MS6_BIT7_0	0x52
>> +#define CEC_LOGICERRLOW_3MS6_BIT8	0x53
>> +#define CEC_CHKCONTENTION_0MS1		0x54
>> +#define CEC_PREPARENXTBIT_0MS05_BIT7_0	0x56
>> +#define CEC_PREPARENXTBIT_0MS05_BIT8	0x57
>> +#define CEC_NOMSMPACKPOINT_0MS45	0x58
>> +#define CEC_ACK0NOML2H_1MS5_BIT7_0	0x5A
>> +#define CEC_ACK0NOML2H_1MS5_BIT8	0x5B
>> +#define CEC_BUGFIX_DISABLE_0		0x60
>> +#define CEC_BUGFIX_DISABLE_1		0x61
>> +#define CEC_RX_MSG_0_HEADER		0x80
>> +#define CEC_RX_MSG_1_OPCODE		0x81
>> +#define CEC_RX_MSG_2_OP1		0x82
>> +#define CEC_RX_MSG_3_OP2		0x83
>> +#define CEC_RX_MSG_4_OP3		0x84
>> +#define CEC_RX_MSG_5_OP4		0x85
>> +#define CEC_RX_MSG_6_OP5		0x86
>> +#define CEC_RX_MSG_7_OP6		0x87
>> +#define CEC_RX_MSG_8_OP7		0x88
>> +#define CEC_RX_MSG_9_OP8		0x89
>> +#define CEC_RX_MSG_A_OP9		0x8A
>> +#define CEC_RX_MSG_B_OP10		0x8B
>> +#define CEC_RX_MSG_C_OP11		0x8C
>> +#define CEC_RX_MSG_D_OP12		0x8D
>> +#define CEC_RX_MSG_E_OP13		0x8E
>> +#define CEC_RX_MSG_F_OP14		0x8F
>> +#define CEC_RX_MSG_LENGTH		0x90
>> +#define CEC_RX_MSG_STATUS		0x91
>> +#define CEC_RX_NUM_MSG			0x92
>> +#define CEC_TX_MSG_STATUS		0x93
>> +#define CEC_TX_NUM_MSG			0x94
>> +
>> +
>> +/* CEC_TX_MSG_CMD definition */
>> +#define TX_NO_OP	0  /* No transaction */
>> +#define TX_REQ_CURRENT	1  /* Transmit earliest message in buffer */
>> +#define TX_ABORT	2  /* Abort transmitting earliest message */
>> +#define TX_REQ_NEXT	3  /* Overwrite earliest msg, transmit next */
>> +
>> +/* tx_msg_status definition */
>> +#define TX_IDLE		0  /* No transaction */
>> +#define TX_BUSY		1  /* Transmitter is busy */
>> +#define TX_DONE		2  /* Message successfully transmitted */
>> +#define TX_ERROR	3  /* Message transmitted with error */
>> +
>> +/* rx_msg_cmd */
>> +#define RX_NO_OP	0  /* No transaction */
>> +#define RX_ACK_CURRENT	1  /* Read earliest message in buffer */
>> +#define RX_DISABLE	2  /* Disable receiving latest message */
>> +#define RX_ACK_NEXT	3  /* Clear earliest msg, read next */
>> +
>> +/* rx_msg_status */
>> +#define RX_IDLE		0  /* No transaction */
>> +#define RX_BUSY		1  /* Receiver is busy */
>> +#define RX_DONE		2  /* Message has been received successfully */
>> +#define RX_ERROR	3  /* Message has been received with error */
>> +
>> +/* RX_CLEAR_BUF options */
>> +#define CLEAR_START	1
>> +#define CLEAR_STOP	0
>> +
>> +/* CEC_LOGICAL_ADDRx options */
>> +#define LOGICAL_ADDR_MASK	0xf
>> +#define LOGICAL_ADDR_VALID	BIT(4)
>> +#define LOGICAL_ADDR_DISABLE	0
>> +
>> +#define CEC_CLK_RATE		32768
>> +
>> +struct meson_ao_cec_device {
>> +	struct platform_device		*pdev;
>> +	void __iomem			*base;
>> +	struct clk			*core;
>> +	spinlock_t			cec_reg_lock;
>> +	struct cec_notifier		*notify;
>> +	struct cec_adapter		*adap;
>> +	struct cec_msg			rx_msg;
>> +};
>> +
>> +#define writel_bits_relaxed(mask, val, addr) \
>> +	writel_relaxed((readl_relaxed(addr) & ~(mask)) | (val), addr)
>> +
>> +static inline void meson_ao_cec_wait_busy(struct meson_ao_cec_device *ao_cec)
>> +{
>> +	while (readl_relaxed(ao_cec->base + CEC_RW_REG) &
>> +			CEC_RW_BUS_BUSY)
>> +		;
> 
> Perhaps add some timeout here in case something locks up?

Ok, any suggestions on what to use here ?

> 
>> +}
>> +
>> +static u8 meson_ao_cec_read(struct meson_ao_cec_device *ao_cec,
>> +			    unsigned long address)
>> +{
>> +	unsigned long flags;
>> +	u32 reg = FIELD_PREP(CEC_RW_ADDR, address);
>> +	u8 data;
>> +
>> +	spin_lock_irqsave(&ao_cec->cec_reg_lock, flags);
>> +
>> +	meson_ao_cec_wait_busy(ao_cec);
>> +
>> +	writel_relaxed(reg, ao_cec->base + CEC_RW_REG);
>> +
>> +	meson_ao_cec_wait_busy(ao_cec);
>> +
>> +	data = FIELD_GET(CEC_RW_RD_DATA,
>> +			 readl_relaxed(ao_cec->base + CEC_RW_REG));
>> +
>> +	spin_unlock_irqrestore(&ao_cec->cec_reg_lock, flags);
>> +
>> +	return data;
>> +}
>> +
>> +static void meson_ao_cec_write(struct meson_ao_cec_device *ao_cec,
>> +			       unsigned long address, u8 data)
>> +{
>> +	unsigned long flags;
>> +	u32 reg = FIELD_PREP(CEC_RW_ADDR, address) |
>> +		  FIELD_PREP(CEC_RW_WR_DATA, data) |
>> +		  CEC_RW_WRITE_EN;
>> +
>> +	spin_lock_irqsave(&ao_cec->cec_reg_lock, flags);
>> +
>> +	meson_ao_cec_wait_busy(ao_cec);
>> +
>> +	writel_relaxed(reg, ao_cec->base + CEC_RW_REG);
>> +
>> +	spin_unlock_irqrestore(&ao_cec->cec_reg_lock, flags);
>> +}
>> +
>> +static inline void meson_ao_cec_irq_setup(struct meson_ao_cec_device *ao_cec,
>> +				      bool enable)
>> +{
>> +	u32 cfg = CEC_INTR_TX | CEC_INTR_RX;
>> +
>> +	writel_bits_relaxed(cfg, enable ? cfg : 0,
>> +			    ao_cec->base + CEC_INTR_MASKN_REG);
>> +}
>> +
>> +static inline void meson_ao_cec_clear(struct meson_ao_cec_device *ao_cec)
>> +{
>> +	meson_ao_cec_write(ao_cec, CEC_RX_MSG_CMD, RX_DISABLE);
>> +	meson_ao_cec_write(ao_cec, CEC_TX_MSG_CMD, TX_ABORT);
>> +	meson_ao_cec_write(ao_cec, CEC_RX_CLEAR_BUF, 1);
>> +	meson_ao_cec_write(ao_cec, CEC_TX_CLEAR_BUF, 1);
>> +
>> +	udelay(100);
>> +
>> +	meson_ao_cec_write(ao_cec, CEC_RX_CLEAR_BUF, 0);
>> +	meson_ao_cec_write(ao_cec, CEC_TX_CLEAR_BUF, 0);
>> +
>> +	udelay(100);
>> +
>> +	meson_ao_cec_write(ao_cec, CEC_RX_MSG_CMD, RX_NO_OP);
>> +	meson_ao_cec_write(ao_cec, CEC_TX_MSG_CMD, TX_NO_OP);
>> +}
>> +
>> +static void meson_ao_cec_arbit_bit_time_set(struct meson_ao_cec_device *ao_cec,
>> +					 unsigned int bit_set,
>> +					 unsigned int time_set)
>> +{
>> +	switch (bit_set) {
>> +	case 3:
> 
> Use CEC_SIGNAL_FREE_TIME_RETRY and friends instead of hardcoding these numbers.

Ok

> 
>> +		meson_ao_cec_write(ao_cec, CEC_TXTIME_4BIT_BIT7_0,
>> +				   time_set & 0xff);
>> +		meson_ao_cec_write(ao_cec, CEC_TXTIME_4BIT_BIT10_8,
>> +				   (time_set >> 8) & 0x7);
>> +		break;
>> +
>> +	case 5:
>> +		meson_ao_cec_write(ao_cec, CEC_TXTIME_2BIT_BIT7_0,
>> +				   time_set & 0xff);
>> +		meson_ao_cec_write(ao_cec, CEC_TXTIME_2BIT_BIT10_8,
>> +				   (time_set >> 8) & 0x7);
>> +		break;
>> +
>> +	case 7:
>> +		meson_ao_cec_write(ao_cec, CEC_TXTIME_17MS_BIT7_0,
>> +				   time_set & 0xff);
>> +		meson_ao_cec_write(ao_cec, CEC_TXTIME_17MS_BIT10_8,
>> +				   (time_set >> 8) & 0x7);
>> +		break;
>> +	}
>> +}
>> +
>> +static irqreturn_t meson_ao_cec_irq(int irq, void *data)
>> +{
>> +	struct meson_ao_cec_device *ao_cec = data;
>> +	u32 stat = readl_relaxed(ao_cec->base + CEC_INTR_STAT_REG);
>> +
>> +	if (stat)
>> +		return IRQ_WAKE_THREAD;
>> +
>> +	return IRQ_NONE;
>> +}
>> +
>> +static void meson_ao_cec_irq_tx(struct meson_ao_cec_device *ao_cec)
>> +{
>> +	unsigned long tx_status = 0;
>> +	u8 stat = meson_ao_cec_read(ao_cec, CEC_TX_MSG_STATUS);
>> +
>> +	switch (stat) {
>> +	case TX_DONE:
>> +		tx_status = CEC_TX_STATUS_OK;
>> +		break;
>> +
>> +	case TX_BUSY:
>> +		tx_status = CEC_TX_STATUS_ARB_LOST;
>> +		break;
>> +
>> +	case TX_IDLE:
>> +		tx_status = CEC_TX_STATUS_LOW_DRIVE;
>> +		break;
>> +
>> +	case TX_ERROR:
>> +	default:
>> +		tx_status = CEC_TX_STATUS_NACK;
> 
> Add a break here.

Ok

> 
>> +	}
>> +
>> +	/* Clear Interruption */
>> +	writel_relaxed(CEC_INTR_TX, ao_cec->base + CEC_INTR_CLR_REG);
>> +
>> +	/* Stop TX */
>> +	meson_ao_cec_write(ao_cec, CEC_TX_MSG_CMD, TX_NO_OP);
>> +
>> +	cec_transmit_attempt_done(ao_cec->adap, tx_status);
>> +}
>> +
>> +static void meson_ao_cec_irq_rx(struct meson_ao_cec_device *ao_cec)
>> +{
>> +	u8 stat = meson_ao_cec_read(ao_cec, CEC_RX_MSG_STATUS);
>> +	int i;
>> +
>> +	/* RX Error */
>> +	if (stat != RX_DONE ||
>> +	    meson_ao_cec_read(ao_cec, CEC_RX_NUM_MSG) != 1)
>> +		goto rx_out;
>> +
>> +	ao_cec->rx_msg.len = meson_ao_cec_read(ao_cec, CEC_RX_MSG_LENGTH) + 1;
>> +	if (ao_cec->rx_msg.len > CEC_MAX_MSG_SIZE)
>> +		ao_cec->rx_msg.len = CEC_MAX_MSG_SIZE;
>> +
>> +	for (i = 0; i < ao_cec->rx_msg.len; i++)
>> +		ao_cec->rx_msg.msg[i] =
>> +			meson_ao_cec_read(ao_cec, CEC_RX_MSG_0_HEADER + i);
>> +
>> +	cec_received_msg(ao_cec->adap, &ao_cec->rx_msg);
>> +
>> +rx_out:
>> +	/* Clear Interruption */
>> +	writel_relaxed(CEC_INTR_RX, ao_cec->base + CEC_INTR_CLR_REG);
>> +
>> +	/* Ack RX message */
>> +	meson_ao_cec_write(ao_cec, CEC_RX_MSG_CMD, RX_ACK_CURRENT);
>> +	meson_ao_cec_write(ao_cec, CEC_RX_MSG_CMD, RX_NO_OP);
>> +
>> +	/* Clear RX buffer */
>> +	meson_ao_cec_write(ao_cec, CEC_RX_CLEAR_BUF, CLEAR_START);
>> +	meson_ao_cec_write(ao_cec, CEC_RX_CLEAR_BUF, CLEAR_STOP);
>> +}
>> +
>> +static irqreturn_t meson_ao_cec_irq_thread(int irq, void *data)
>> +{
>> +	struct meson_ao_cec_device *ao_cec = data;
>> +	u32 stat = readl_relaxed(ao_cec->base + CEC_INTR_STAT_REG);
>> +
>> +	if (stat & CEC_INTR_TX)
>> +		meson_ao_cec_irq_tx(ao_cec);
>> +
>> +	meson_ao_cec_irq_rx(ao_cec);
>> +
>> +	return IRQ_HANDLED;
>> +}
>> +
>> +static int meson_ao_cec_set_log_addr(struct cec_adapter *adap, u8 logical_addr)
>> +{
>> +	struct meson_ao_cec_device *ao_cec = adap->priv;
>> +
>> +	meson_ao_cec_write(ao_cec, CEC_LOGICAL_ADDR0, LOGICAL_ADDR_DISABLE);
>> +
>> +	meson_ao_cec_clear(ao_cec);
>> +
>> +	if (logical_addr == CEC_LOG_ADDR_INVALID)
>> +		return 0;
>> +
>> +	meson_ao_cec_write(ao_cec, CEC_LOGICAL_ADDR0,
>> +			   logical_addr & LOGICAL_ADDR_MASK);
>> +
>> +	udelay(100);
>> +
>> +	meson_ao_cec_write(ao_cec, CEC_LOGICAL_ADDR0,
>> +			   (logical_addr & LOGICAL_ADDR_MASK) |
>> +			   LOGICAL_ADDR_VALID);
>> +
>> +	return 0;
>> +}
>> +
>> +static int meson_ao_cec_transmit(struct cec_adapter *adap, u8 attempts,
>> +				 u32 signal_free_time, struct cec_msg *msg)
>> +{
>> +	struct meson_ao_cec_device *ao_cec = adap->priv;
>> +	u8 reg;
>> +	int i;
>> +
>> +	reg = meson_ao_cec_read(ao_cec, CEC_TX_MSG_STATUS);
>> +	if (reg == TX_BUSY) {
>> +		dev_err(&ao_cec->pdev->dev, "%s: busy TX\n", __func__);
>> +		meson_ao_cec_write(ao_cec, CEC_TX_MSG_CMD, TX_ABORT);
>> +	}
>> +
>> +	for (i = 0; i < msg->len; i++)
>> +		meson_ao_cec_write(ao_cec, CEC_TX_MSG_0_HEADER + i,
>> +				   msg->msg[i]);
>> +
>> +	meson_ao_cec_write(ao_cec, CEC_TX_MSG_LENGTH, msg->len - 1);
>> +	meson_ao_cec_write(ao_cec, CEC_TX_MSG_CMD, TX_REQ_CURRENT);
>> +
>> +	return 0;
>> +}
>> +
>> +static int meson_ao_cec_adap_enable(struct cec_adapter *adap, bool enable)
>> +{
>> +	struct meson_ao_cec_device *ao_cec = adap->priv;
>> +
>> +	meson_ao_cec_irq_setup(ao_cec, false);
>> +
>> +	writel_bits_relaxed(CEC_GEN_CNTL_RESET, CEC_GEN_CNTL_RESET,
>> +			    ao_cec->base + CEC_GEN_CNTL_REG);
>> +
>> +	if (!enable)
>> +		return 0;
>> +
>> +	/* Enable gated clock (Normal mode). */
>> +	writel_bits_relaxed(CEC_GEN_CNTL_CLK_CTRL_MASK,
>> +			    FIELD_PREP(CEC_GEN_CNTL_CLK_CTRL_MASK,
>> +				       CEC_GEN_CNTL_CLK_ENABLE),
>> +			    ao_cec->base + CEC_GEN_CNTL_REG);
>> +
>> +	udelay(100);
>> +
>> +	/* Release Reset */
>> +	writel_bits_relaxed(CEC_GEN_CNTL_RESET, 0,
>> +			    ao_cec->base + CEC_GEN_CNTL_REG);
>> +
>> +	/* Clear buffers */
>> +	meson_ao_cec_clear(ao_cec);
>> +
>> +	/* CEC arbitration 3/5/7 bit time set. */
>> +	meson_ao_cec_arbit_bit_time_set(ao_cec, 3, 0x118);
>> +	meson_ao_cec_arbit_bit_time_set(ao_cec, 5, 0x000);
>> +	meson_ao_cec_arbit_bit_time_set(ao_cec, 7, 0x2aa);
> 
> Use CEC_SIGNAL_FREE_TIME_RETRY etc. defines.

Ok

> 
>> +
>> +	meson_ao_cec_irq_setup(ao_cec, true);
>> +
>> +	return 0;
>> +}
>> +
>> +static const struct cec_adap_ops meson_ao_cec_ops = {
>> +	.adap_enable = meson_ao_cec_adap_enable,
>> +	.adap_log_addr = meson_ao_cec_set_log_addr,
>> +	.adap_transmit = meson_ao_cec_transmit,
>> +};
>> +
>> +static int meson_ao_cec_probe(struct platform_device *pdev)
>> +{
>> +	struct meson_ao_cec_device *ao_cec;
>> +	struct platform_device *hdmi_dev;
>> +	struct device_node *np;
>> +	struct resource *res;
>> +	int ret, irq;
>> +
>> +	np = of_parse_phandle(pdev->dev.of_node, "hdmi-phandle", 0);
>> +	if (!np) {
>> +		dev_err(&pdev->dev, "Failed to find hdmi node\n");
>> +		return -ENODEV;
>> +	}
>> +
>> +	hdmi_dev = of_find_device_by_node(np);
>> +	if (hdmi_dev == NULL)
>> +		return -EPROBE_DEFER;
>> +
>> +	ao_cec = devm_kzalloc(&pdev->dev, sizeof(*ao_cec), GFP_KERNEL);
>> +	if (!ao_cec)
>> +		return -ENOMEM;
>> +
>> +	spin_lock_init(&ao_cec->cec_reg_lock);
>> +
>> +	ao_cec->notify = cec_notifier_get(&hdmi_dev->dev);
>> +	if (!ao_cec->notify)
>> +		return -ENOMEM;
>> +
>> +	ao_cec->adap = cec_allocate_adapter(&meson_ao_cec_ops, ao_cec,
>> +					    "meson_ao_cec",
>> +					    CEC_CAP_LOG_ADDRS |
>> +					    CEC_CAP_TRANSMIT |
>> +					    CEC_CAP_RC,
> 
> Add CEC_CAP_PASSTHROUGH as well.

Ok

> 
> Is MONITOR_ALL functionality supported? If so, then I would recommend that
> that is implemented.

Seems not, I found no sign of it.

> 
>> +					    1); /* Use 1 for now */
>> +	if (IS_ERR(ao_cec->adap)) {
>> +		ret = PTR_ERR(ao_cec->adap);
>> +		goto out_probe_notify;
>> +	}
>> +
>> +	ao_cec->adap->owner = THIS_MODULE;
>> +
>> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +	ao_cec->base = devm_ioremap_resource(&pdev->dev, res);
>> +	if (IS_ERR(ao_cec->base)) {
>> +		ret = PTR_ERR(ao_cec->base);
>> +		goto out_probe_adapter;
>> +	}
>> +
>> +	irq = platform_get_irq(pdev, 0);
>> +	ret = devm_request_threaded_irq(&pdev->dev, irq,
>> +					meson_ao_cec_irq,
>> +					meson_ao_cec_irq_thread,
>> +					0, NULL, ao_cec);
>> +	if (ret) {
>> +		dev_err(&pdev->dev, "irq request failed\n");
>> +		goto out_probe_adapter;
>> +	}
>> +
>> +	ao_cec->core = devm_clk_get(&pdev->dev, "core");
>> +	if (IS_ERR(ao_cec->core)) {
>> +		dev_err(&pdev->dev, "core clock request failed\n");
>> +		ret = PTR_ERR(ao_cec->core);
>> +		goto out_probe_adapter;
>> +	}
>> +
>> +	ret = clk_prepare_enable(ao_cec->core);
>> +	if (ret) {
>> +		dev_err(&pdev->dev, "core clock enable failed\n");
>> +		goto out_probe_adapter;
>> +	}
>> +
>> +	ret = clk_set_rate(ao_cec->core, CEC_CLK_RATE);
>> +	if (ret) {
>> +		dev_err(&pdev->dev, "core clock set rate failed\n");
>> +		goto out_probe_clk;
>> +	}
>> +
>> +	device_reset_optional(&pdev->dev);
>> +
>> +	ao_cec->pdev = pdev;
>> +	platform_set_drvdata(pdev, ao_cec);
>> +
>> +	ret = cec_register_adapter(ao_cec->adap, &pdev->dev);
>> +	if (ret < 0) {
>> +		cec_notifier_put(ao_cec->notify);
>> +		goto out_probe_clk;
>> +	}
>> +
>> +	/* Setup Hardware */
>> +	writel_relaxed(CEC_GEN_CNTL_RESET,
>> +		       ao_cec->base + CEC_GEN_CNTL_REG);
>> +
>> +	cec_register_cec_notifier(ao_cec->adap, ao_cec->notify);
>> +
>> +	return 0;
>> +
>> +out_probe_clk:
>> +	clk_disable_unprepare(ao_cec->core);
>> +
>> +out_probe_adapter:
>> +	cec_delete_adapter(ao_cec->adap);
>> +
>> +out_probe_notify:
>> +	cec_notifier_put(ao_cec->notify);
>> +
>> +	dev_err(&pdev->dev, "CEC controller registration failed\n");
>> +
>> +	return ret;
>> +}
>> +
>> +static int meson_ao_cec_remove(struct platform_device *pdev)
>> +{
>> +	struct meson_ao_cec_device *ao_cec = platform_get_drvdata(pdev);
>> +
>> +	clk_disable_unprepare(ao_cec->core);
>> +
>> +	cec_unregister_adapter(ao_cec->adap);
>> +
>> +	cec_notifier_put(ao_cec->notify);
>> +
>> +	return 0;
>> +}
>> +
>> +static const struct of_device_id meson_ao_cec_of_match[] = {
>> +	{ .compatible = "amlogic,meson-gx-ao-cec", },
>> +	{ /* sentinel */ }
>> +};
>> +MODULE_DEVICE_TABLE(of, meson_ao_cec_of_match);
>> +
>> +static struct platform_driver meson_ao_cec_driver = {
>> +	.probe   = meson_ao_cec_probe,
>> +	.remove  = meson_ao_cec_remove,
>> +	.driver  = {
>> +		.name = "meson-ao-cec",
>> +		.of_match_table = of_match_ptr(meson_ao_cec_of_match),
>> +	},
>> +};
>> +
>> +module_platform_driver(meson_ao_cec_driver);
>> +
>> +MODULE_DESCRIPTION("Meson AO CEC Controller driver");
>> +MODULE_AUTHOR("Neil Armstrong <narmstrong@xxxxxxxxxxxx>");
>> +MODULE_LICENSE("GPL");
>>
> 
> Regards,
> 
> 	Hans
> 

Thanks,
Neil




[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux