Steve, Jack, All, On Fri, Jun 17, 2016 at 12:01:41PM -0700, Steve Longerbeam wrote: > > On 06/17/2016 08:18 AM, Gary Bisson wrote: > > Steve, All, > > > > On Thu, Jun 16, 2016 at 10:32:31AM +0200, Gary Bisson wrote: > > > Steve, All, > > > > > > On Tue, Jun 14, 2016 at 03:49:15PM -0700, Steve Longerbeam wrote: > > > > Defines the host video capture device node and an OV5642 camera sensor > > > > node on i2c2. The host capture device connects to the OV5642 via the > > > > parallel-bus mux input on the ipu1_csi0_mux. > > > > > > > > Note there is a pin conflict with GPIO6. This pin functions as a power > > > > input pin to the OV5642, but ENET requires it to wake-up the ARM cores > > > > on normal RX and TX packet done events (see 6261c4c8). So by default, > > > > capture is disabled, enable by uncommenting __OV5642_CAPTURE__ macro. > > > > Ethernet will still work just not quite as well. > > > Actually the following patch fixes this issue and has already been > > > applied on Shawn's tree: > > > https://patchwork.kernel.org/patch/9153523/ > > > > > > Also, this follow-up patch declared the HW workaround for SabreLite: > > > https://patchwork.kernel.org/patch/9153525/ > > > > > > So ideally, once those two patches land on your base tree, you could get > > > rid of the #define and remove the HW workaround declaration. > > > > > > Finally, I'll test the series on Sabre-Lite this week. > > I've applied this series on top of Shawn tree (for-next branch) in order > > not to worry about the GPIO6 workaround. > > > > Although the camera seems to get enumerated properly, I can't seem to > > get anything from it. See log: > > http://pastebin.com/xnw1ujUq > > Hi Gary, the driver does not implement vidioc_cropcap, it has > switched to the new selection APIs and v4l2src should be using > vidioc_g_selection instead of vidioc_cropcap. I confirm this was the issue, your patch fixes it. > > In your cover letter, you said that you have not run through > > v4l2-compliance. How have you tested the capture? > > I use v4l2-ctl, and have used v4l2src in the past, but that was before > switching to the selection APIs. Try the attached hack that adds > vidioc_cropcap back in, and see how far you get on SabreLite with > v4l2src. I tried the following on SabreAuto: > > gst-launch-1.0 v4l2src io_mode=4 ! > "video/x-raw,format=RGB16,width=640,height=480" ! fbdevsink I confirm that works with OV5642 on SabreLite: Tested-by: Gary Bisson <gary.bisson@xxxxxxxxxxxxxxxxxxx> > > Also, why isn't the OV5640 MIPI camera declared on the SabreLite device > > tree? > > See Jack Mitchell's patch at http://ix.io/TTg. Thanks Jack! I will work on > incorporating it. I've tried that patch have a some comments: - When applied, no capture shows up any more, instead I have two m2m v4l2 devices [1]. - OV5640 Mipi is assigned the same address as OV5642, therefore both can't work at the same time right now. There's a register in the camera that allows to modify its I2C address, see this patch [2]. - How is the mclk working in this patch? It should be using the PWM3 output to generate a ~22MHz clock. I would expect the use of a pwm-clock node [3]. Also another remark on both OV5642 and OV5640 patches, is it recommended to use 0x80000000 pin muxing value? This leaves it to the bootloader to properly setup the I/O. It sounds safer to properly set them up in the device tree in my opinion in order not to be dependent on the bootloader. All the above remarks said, thanks for this work on i.MX camera support, that feature will be highly appreciated. Regards, Gary [1] http://pastebin.com/i5MrhB1h [2] https://github.com/boundarydevices/linux-imx6/commit/f915806d [3] http://lxr.free-electrons.com/source/Documentation/devicetree/bindings/clock/pwm-clock.txt -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
