Hi! I have problems to get my Asustek P1731 Dual working. I have install v4l-dvb and the firmware dvb-fe-tda10046.fw. The module saa7134-dvb loads fine, but dmesg shows: tda827xo_set_params: could not write to tuner at addr: 0xc2 saa7134[0]/dvb: could not access tda8290 I2C gate saa7134[0]/dvb: could not access tda8290 I2C gate saa7134[0]/dvb: could not access tda8290 I2C gate Also, w_scan cant tune: w_scan version 20080105 Info: using DVB adapter auto detection. Found DVB-T frontend. Using adapter /dev/dvb/adapter0/frontend0 -_-_-_-_ Getting frontend capabilities-_-_-_-_ frontend Philips TDA10046H DVB-T supports INVERSION_AUTO QAM_AUTO TRANSMISSION_MODE_AUTO GUARD_INTERVAL_AUTO HIERARCHY_AUTO not supported, trying HIERARCHY_NONE. FEC_AUTO -_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_ 177500: 184500: 191500: 198500: ........... .................... .................... ERROR: Sorry - i couldn't get any working frequency/transponder Nothing to scan!! dumping lists (0 services) Done. dmesg while loading with modprobe saa7134 card=112 tuner=54 gpio_tracking=1 i2c_scan=1 is the same: saa7130/34: v4l2 driver version 0.2.14 loaded saa7134[0]: found at 0000:03:04.0, rev: 1, irq: 16, latency: 64, mmio: 0xbffff000 saa7134[0]: subsystem: 1043:4860, board: ASUSTeK P7131 Dual [card=78,insmod option] saa7134[0]: board init: gpio is 0 saa7134[0]: gpio: mode=0x0000000 in=0x0000000 out=0x0000000 [pre-init] input: saa7134 IR (ASUSTeK P7131 Dual) as /class/input/input10 saa7134[0]: i2c eeprom 00: 43 10 60 48 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7134[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 20: 01 40 01 03 03 02 03 04 08 ff 00 4c ff ff ff ff saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 40: ff 1d 00 c2 86 10 01 01 0d 01 ff ff ff ff ff ff saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c scan: found device @ 0x10 [???] saa7134[0]: i2c scan: found device @ 0xa0 [eeprom] saa7134[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television] saa7134[0]: registered device video0 [v4l2] saa7134[0]: registered device vbi0 saa7134[0]: registered device radio0 dvb_init() allocating 1 frontend DVB: registering new adapter (saa7134[0]) DVB: registering adapter 0 frontend 0 (Philips TDA10046H DVB-T)... tda1004x: setting up plls for 48MHz sampling clock tda1004x: found firmware revision 20 -- ok saa7134[0]/dvb: could not access tda8290 I2C gate saa7134[0]/dvb: could not access tda8290 I2C gate It's seems there's a problems while writen in the EEPROM. -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
