From: Greg Ungerer <gerg@xxxxxxxxxxx>
If we make all UART addressing consistent across all ColdFire family members
then we will be able to remove the duplicated plaform data and use a single
setup for all.
So modify the ColdFire 5206 UART addressing so that:
. UARTs are numbered from 0 up
. base addresses are absolute (not relative to MBAR peripheral register)
. use a common name for IRQs used
Signed-off-by: Greg Ungerer <gerg@xxxxxxxxxxx>
---
arch/m68k/include/asm/m5206sim.h | 10 ++++++----
arch/m68k/platform/5206/config.c | 12 ++++++------
2 files changed, 12 insertions(+), 10 deletions(-)
diff --git a/arch/m68k/include/asm/m5206sim.h b/arch/m68k/include/asm/m5206sim.h
index 9015ead..6972236 100644
--- a/arch/m68k/include/asm/m5206sim.h
+++ b/arch/m68k/include/asm/m5206sim.h
@@ -100,11 +100,11 @@
#define MCFDMA_BASE1 (MCF_MBAR + 0x240) /* Base address DMA 1 */
#if defined(CONFIG_NETtel)
-#define MCFUART_BASE1 0x180 /* Base address of UART1 */
-#define MCFUART_BASE2 0x140 /* Base address of UART2 */
+#define MCFUART_BASE0 (MCF_MBAR + 0x180) /* Base address UART0 */
+#define MCFUART_BASE1 (MCF_MBAR + 0x140) /* Base address UART1 */
#else
-#define MCFUART_BASE1 0x140 /* Base address of UART1 */
-#define MCFUART_BASE2 0x180 /* Base address of UART2 */
+#define MCFUART_BASE0 (MCF_MBAR + 0x140) /* Base address UART0 */
+#define MCFUART_BASE1 (MCF_MBAR + 0x180) /* Base address UART1 */
#endif
/*
@@ -112,6 +112,8 @@
*/
#define MCF_IRQ_TIMER 30 /* Timer0, Level 6 */
#define MCF_IRQ_PROFILER 31 /* Timer1, Level 7 */
+#define MCF_IRQ_UART0 73 /* UART0 */
+#define MCF_IRQ_UART1 74 /* UART1 */
/*
* Generic GPIO
diff --git a/arch/m68k/platform/5206/config.c b/arch/m68k/platform/5206/config.c
index 6fa3f80..e21608c 100644
--- a/arch/m68k/platform/5206/config.c
+++ b/arch/m68k/platform/5206/config.c
@@ -22,12 +22,12 @@
static struct mcf_platform_uart m5206_uart_platform[] = {
{
- .mapbase = MCF_MBAR + MCFUART_BASE1,
- .irq = 73,
+ .mapbase = MCFUART_BASE0,
+ .irq = MCF_IRQ_UART0,
},
{
- .mapbase = MCF_MBAR + MCFUART_BASE2,
- .irq = 74,
+ .mapbase = MCFUART_BASE1,
+ .irq = MCF_IRQ_UART1,
},
{ },
};
@@ -48,11 +48,11 @@ static void __init m5206_uart_init_line(int line, int irq)
{
if (line == 0) {
writel(MCFSIM_ICR_LEVEL6 | MCFSIM_ICR_PRI1, MCF_MBAR + MCFSIM_UART1ICR);
- writeb(irq, MCFUART_BASE1 + MCFUART_UIVR);
+ writeb(irq, MCFUART_BASE0 + MCFUART_UIVR);
mcf_mapirq2imr(irq, MCFINTC_UART0);
} else if (line == 1) {
writel(MCFSIM_ICR_LEVEL6 | MCFSIM_ICR_PRI2, MCF_MBAR + MCFSIM_UART2ICR);
- writeb(irq, MCFUART_BASE2 + MCFUART_UIVR);
+ writeb(irq, MCFUART_BASE1 + MCFUART_UIVR);
mcf_mapirq2imr(irq, MCFINTC_UART1);
}
}
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-m68k" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
