Re: [PATCH v2 3/6] net: phy: DP83640: Add LED handling

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello Bastien,

On Tue, 27 Feb 2024 10:39:42 +0100
Bastien Curutchet <bastien.curutchet@xxxxxxxxxxx> wrote:

> The PHY have three LED : Activity LED, Speed LED and Link LED. The PHY
> offers three configuration modes for them. The driver does not handle them.
> 
> Add LED handling through the /sys/class/leds interface.
> On every mode the Speed LED indicates the speed (10Mbps or 100 Mbps) and
> the Link LED indicates whether the link is good or not. Link LED will also
> reflects link activity in mode 2 and 3. The Activity LED can reflect the
> link activity (mode 1), the link's duplex (mode 2) or collisions on the
> link (mode 3).
> Only the Activity LED can have its hardware configuration updated, it
> has an impact on Link LED as activity reflexion is added on it on modes
> 2 and 3
> 
> Signed-off-by: Bastien Curutchet <bastien.curutchet@xxxxxxxxxxx>

Regarding the LED management I don't have much knowledge on it,
however I do have comments on the code itself :)

> ---
>  drivers/net/phy/dp83640.c     | 176 ++++++++++++++++++++++++++++++++++
>  drivers/net/phy/dp83640_reg.h |  11 +++
>  2 files changed, 187 insertions(+)
> 
> diff --git a/drivers/net/phy/dp83640.c b/drivers/net/phy/dp83640.c
> index 5c42c47dc564..c46c81ef0ad0 100644
> --- a/drivers/net/phy/dp83640.c
> +++ b/drivers/net/phy/dp83640.c
> @@ -59,6 +59,22 @@
>  				   MII_DP83640_MISR_SPD_INT |\
>  				   MII_DP83640_MISR_LINK_INT)
>  
> +#define DP83640_ACTLED_IDX	0
> +#define DP83640_LNKLED_IDX	1
> +#define DP83640_SPDLED_IDX	2
> +/* LNKLED = ON for Good Link, OFF for No Link */
> +/* SPDLED = ON in 100 Mb/s, OFF in 10 Mb/s */
> +/* ACTLED = ON for Activity, OFF for No Activity */
> +#define DP83640_LED_MODE_1	1
> +/* LNKLED = ON for Good Link, Blink for Activity */
> +/* SPDLED = ON in 100 Mb/s, OFF in 10 Mb/s */
> +/* ACTLED = ON for Collision, OFF for No Collision */
> +#define DP83640_LED_MODE_2	2
> +/* LNKLED = ON for Good Link, Blink for Activity */
> +/* SPDLED = ON in 100 Mb/s, OFF in 10 Mb/s */
> +/* ACTLED = ON for Full-Duplex, OFF for Half-Duplex */
> +#define DP83640_LED_MODE_3	3
> +
>  /* phyter seems to miss the mark by 16 ns */
>  #define ADJTIME_FIX	16
>  
> @@ -1515,6 +1531,161 @@ static void dp83640_remove(struct phy_device *phydev)
>  	kfree(dp83640);
>  }
>  
> +static int dp83640_led_brightness_set(struct phy_device *phydev, u8 index,
> +				      enum led_brightness brightness)
> +{
> +	int val;
> +
> +	if (index > DP83640_SPDLED_IDX)
> +		return -EINVAL;
> +
> +	phy_write(phydev, PAGESEL, 0);
> +
> +	val = phy_read(phydev, LEDCR) & ~DP83640_LED_DIS(index);
> +	val |= DP83640_LED_DRV(index);
> +	if (brightness)
> +		val |= DP83640_LED_VAL(index);
> +	else
> +		val &= ~DP83640_LED_VAL(index);
> +	phy_write(phydev, LEDCR, val);

Looks like you can use phy_modify here

> +
> +	return 0;
> +}
> +
> +/**
> + * dp83640_led_mode - Check the trigger netdev rules and compute the associated
> + *                    configuration mode
> + * @index: The targeted LED
> + * @rules: Rules to be checked
> + *
> + * Returns the mode that is to be set in LED_CFNG. If the rules are not
> + * supported by the PHY, returns -ENOTSUPP. If the rules are supported but don't
> + * impact the LED configuration, returns 0
> + */
> +static int dp83640_led_mode(u8 index, unsigned long rules)
> +{
> +	/* Only changes on ACTLED have an impact on LED Mode configuration */
> +	switch (index) {
> +	case DP83640_ACTLED_IDX:
> +		switch (rules) {
> +		case BIT(TRIGGER_NETDEV_TX) | BIT(TRIGGER_NETDEV_RX):
> +			return DP83640_LED_MODE_1;
> +		case BIT(TRIGGER_NETDEV_COLLISION):
> +			return DP83640_LED_MODE_2;
> +		case BIT(TRIGGER_NETDEV_FULL_DUPLEX) |
> +		     BIT(TRIGGER_NETDEV_HALF_DUPLEX):
> +			return DP83640_LED_MODE_3;
> +		default:
> +			return -EOPNOTSUPP;
> +		}
> +
> +	case DP83640_SPDLED_IDX:
> +		/* SPDLED has the same function in every mode */
> +		switch (rules) {
> +		case BIT(TRIGGER_NETDEV_LINK_10) | BIT(TRIGGER_NETDEV_LINK_100):
> +			return 0;
> +		default:
> +			return -EOPNOTSUPP;
> +		}
> +
> +	case DP83640_LNKLED_IDX:
> +		/* LNKLED has the same function in every mode */
> +		switch (rules) {
> +		case BIT(TRIGGER_NETDEV_LINK):
> +			return 0;
> +		default:
> +			return -EOPNOTSUPP;
> +		}
> +	default:
> +		return -EINVAL;
> +	}
> +}
> +
> +static int dp83640_led_hw_is_supported(struct phy_device *phydev, u8 index,
> +				       unsigned long rules)
> +{
> +	int ret;
> +
> +	ret = dp83640_led_mode(index, rules);
> +
> +	if (ret < 0)
> +		return ret;
> +
> +	return 0;
> +}

It looks like you can just return whatever dp83640_led_mode() returns
directly ?

> +
> +static int dp83640_led_hw_control_set(struct phy_device *phydev, u8 index,
> +				      unsigned long rules)
> +{
> +	int mode, val;
> +
> +	mode = dp83640_led_mode(index, rules);
> +	if (mode < 0)
> +		return mode;
> +
> +	if (mode) {
> +		phy_write(phydev, PAGESEL, 0);

Here the current page is written to 0, don't you need to restore the
page to the original one afterwards ? the broadcast_* functions in the
same driver are always restoring the page to the initial one, I think
you also need that, or unrelated register accesses in the same PHY
driver might write to the wrong page.

If you want that to be done automatically for you, you can implement the
.read_page and .write_page in the driver, then use the
phy_read/write/modify_paged accessors.

> +		val = phy_read(phydev, PHYCR) & ~(LED_CNFG_1 | LED_CNFG_0);
> +		switch (mode) {
> +		case DP83640_LED_MODE_1:
> +			val |= LED_CNFG_0;
> +		break;
> +		case DP83640_LED_MODE_2:
> +			/* Keeping LED_CNFG_1 and LED_CNFG_0 unset */
> +			break;
> +		case DP83640_LED_MODE_3:
> +			val |= LED_CNFG_1;
> +			break;
> +		default:
> +			return -EINVAL;
> +		}
> +		phy_write(phydev, PHYCR, val);
> +	}
> +
> +	val = phy_read(phydev, LEDCR);
> +	val &= ~(DP83640_LED_DIS(index) | DP83640_LED_DRV(index));
> +	phy_write(phydev, LEDCR, val);

You can use phy_modify here aswell

> +
> +	return 0;
> +}
> +
> +static int dp83640_led_hw_control_get(struct phy_device *phydev, u8 index,
> +				      unsigned long *rules)
> +{
> +	int val;
> +
> +	switch (index) {
> +	case DP83640_ACTLED_IDX:
> +		phy_write(phydev, PAGESEL, 0);

Same comment on the page selection here.

> +		val = phy_read(phydev, PHYCR);
> +		if (val & LED_CNFG_0) {
> +			/* Mode 1 */
> +			*rules = BIT(TRIGGER_NETDEV_TX) | BIT(TRIGGER_NETDEV_RX);
> +		} else if (val & LED_CNFG_1) {
> +			/* Mode 3 */
> +			*rules = BIT(TRIGGER_NETDEV_FULL_DUPLEX) |
> +				 BIT(TRIGGER_NETDEV_HALF_DUPLEX);
> +		} else {
> +			/* Mode 2 */
> +			*rules = BIT(TRIGGER_NETDEV_COLLISION);
> +		}
> +		break;
> +
> +	case DP83640_LNKLED_IDX:
> +		*rules = BIT(TRIGGER_NETDEV_LINK);
> +		break;
> +
> +	case DP83640_SPDLED_IDX:
> +		*rules = BIT(TRIGGER_NETDEV_LINK_10) |
> +			 BIT(TRIGGER_NETDEV_LINK_100);
> +		break;
> +	default:
> +		return -EINVAL;
> +	}
> +
> +	return 0;
> +}
> +
>  static struct phy_driver dp83640_driver = {
>  	.phy_id		= DP83640_PHY_ID,
>  	.phy_id_mask	= 0xfffffff0,
> @@ -1526,6 +1697,11 @@ static struct phy_driver dp83640_driver = {
>  	.config_init	= dp83640_config_init,
>  	.config_intr    = dp83640_config_intr,
>  	.handle_interrupt = dp83640_handle_interrupt,
> +
> +	.led_brightness_set = dp83640_led_brightness_set,
> +	.led_hw_is_supported = dp83640_led_hw_is_supported,
> +	.led_hw_control_set = dp83640_led_hw_control_set,
> +	.led_hw_control_get = dp83640_led_hw_control_get,
>  };
>  
>  static int __init dp83640_init(void)
> diff --git a/drivers/net/phy/dp83640_reg.h b/drivers/net/phy/dp83640_reg.h
> index daae7fa58fb8..09dd2d2527c7 100644
> --- a/drivers/net/phy/dp83640_reg.h
> +++ b/drivers/net/phy/dp83640_reg.h
> @@ -6,6 +6,8 @@
>  #define HAVE_DP83640_REGISTERS
>  
>  /* #define PAGE0                  0x0000 */
> +#define LEDCR                     0x0018 /* PHY Control Register */
> +#define PHYCR                     0x0019 /* PHY Control Register */
>  #define PHYCR2                    0x001c /* PHY Control Register 2 */
>  
>  #define PAGE4                     0x0004
> @@ -50,6 +52,15 @@
>  #define PTP_GPIOMON               0x001e /* PTP GPIO Monitor Register */
>  #define PTP_RXHASH                0x001f /* PTP Receive Hash Register */
>  
> +/* Bit definitions for the LEDCR register */
> +#define DP83640_LED_DIS(x)        BIT((x) + 9) /* Disable LED */
> +#define DP83640_LED_DRV(x)        BIT((x) + 3) /* Force LED val to output */
> +#define DP83640_LED_VAL(x)        BIT((x))     /* LED val */
> +
> +/* Bit definitions for the PHYCR register */
> +#define LED_CNFG_0	          BIT(5)  /* LED configuration, bit 0 */
> +#define LED_CNFG_1	          BIT(6)  /* LED configuration, bit 1 */
> +
>  /* Bit definitions for the PHYCR2 register */
>  #define BC_WRITE                  (1<<11) /* Broadcast Write Enable */
>  

Thanks,

Maxime




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux OMAP]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux