[PATCH v18 2/3] leds: flash: mt6370: Add MediaTek MT6370 flashlight support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: ChiYuan Huang <cy_huang@xxxxxxxxxxx>

The MediaTek MT6370 is a highly-integrated smart power management IC,
which includes a single cell Li-Ion/Li-Polymer switching battery
charger, a USB Type-C & Power Delivery (PD) controller, dual Flash
LED current sources, a RGB LED driver, a backlight WLED driver,
a display bias driver and a general LDO for portable devices.

Add support for the MT6370 Flash LED driver. Flash LED in MT6370
has 2 channels and support torch/strobe mode.

Acked-by: Jacek Anaszewski <jacek.anaszewski@xxxxxxxxx>
Co-developed-by: Alice Chen <alice_chen@xxxxxxxxxxx>
Signed-off-by: Alice Chen <alice_chen@xxxxxxxxxxx>
Signed-off-by: ChiYuan Huang <cy_huang@xxxxxxxxxxx>
Signed-off-by: ChiaEn Wu <chiaen_wu@xxxxxxxxxxx>
---
v18:
- Unwrap each line by 100 chars limit.
- For joint flash, add more comments above the source code.
- Remove 'sentinel' comment in of_device_id table declaration.
---
 drivers/leds/flash/Kconfig             |  13 +
 drivers/leds/flash/Makefile            |   1 +
 drivers/leds/flash/leds-mt6370-flash.c | 573 +++++++++++++++++++++++++++++++++
 3 files changed, 587 insertions(+)
 create mode 100644 drivers/leds/flash/leds-mt6370-flash.c

diff --git a/drivers/leds/flash/Kconfig b/drivers/leds/flash/Kconfig
index d3eb689..49d8922 100644
--- a/drivers/leds/flash/Kconfig
+++ b/drivers/leds/flash/Kconfig
@@ -61,6 +61,19 @@ config LEDS_MT6360
 	  Independent current sources supply for each flash LED support torch
 	  and strobe mode.
 
+config LEDS_MT6370_FLASH
+	tristate "Flash LED Support for MediaTek MT6370 PMIC"
+	depends on LEDS_CLASS
+	depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
+	depends on MFD_MT6370
+	help
+	  Support 2 channels and torch/strobe mode.
+	  Say Y here to enable support for
+	  MT6370_FLASH_LED device.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called "leds-mt6370-flash".
+
 config LEDS_RT4505
 	tristate "LED support for RT4505 flashlight controller"
 	depends on I2C && OF
diff --git a/drivers/leds/flash/Makefile b/drivers/leds/flash/Makefile
index 0acbddc..4665e8e 100644
--- a/drivers/leds/flash/Makefile
+++ b/drivers/leds/flash/Makefile
@@ -1,6 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 
 obj-$(CONFIG_LEDS_MT6360)	+= leds-mt6360.o
+obj-$(CONFIG_LEDS_MT6370_FLASH)	+= leds-mt6370-flash.o
 obj-$(CONFIG_LEDS_AAT1290)	+= leds-aat1290.o
 obj-$(CONFIG_LEDS_AS3645A)	+= leds-as3645a.o
 obj-$(CONFIG_LEDS_KTD2692)	+= leds-ktd2692.o
diff --git a/drivers/leds/flash/leds-mt6370-flash.c b/drivers/leds/flash/leds-mt6370-flash.c
new file mode 100644
index 00000000..dc00c33
--- /dev/null
+++ b/drivers/leds/flash/leds-mt6370-flash.c
@@ -0,0 +1,573 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2023 Richtek Technology Corp.
+ *
+ * Authors:
+ *   Alice Chen <alice_chen@xxxxxxxxxxx>
+ *   ChiYuan Huang <cy_huang@xxxxxxxxxxx>
+ */
+
+#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/led-class-flash.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+
+#include <media/v4l2-flash-led-class.h>
+
+enum {
+	MT6370_LED_FLASH1 = 0,
+	MT6370_LED_FLASH2,
+	MT6370_MAX_LEDS
+};
+
+/* Virtual definition for multicolor */
+
+#define MT6370_REG_FLEDEN		0x17E
+#define MT6370_REG_STRBTO		0x173
+#define MT6370_REG_CHGSTAT2		0x1D1
+#define MT6370_REG_FLEDSTAT1		0x1D9
+#define MT6370_REG_FLEDISTRB(_id)	(0x174 + 4 * (_id))
+#define MT6370_REG_FLEDITOR(_id)	(0x175 + 4 * (_id))
+#define MT6370_ITORCH_MASK		GENMASK(4, 0)
+#define MT6370_ISTROBE_MASK		GENMASK(6, 0)
+#define MT6370_STRBTO_MASK		GENMASK(6, 0)
+#define MT6370_TORCHEN_MASK		BIT(3)
+#define MT6370_STROBEN_MASK		BIT(2)
+#define MT6370_FLCSEN_MASK(_id)		BIT(MT6370_LED_FLASH2 - (_id))
+#define MT6370_FLCSEN_MASK_ALL		GENMASK(1, 0)
+#define MT6370_FLEDCHGVINOVP_MASK	BIT(3)
+#define MT6370_FLED1STRBTO_MASK		BIT(11)
+#define MT6370_FLED2STRBTO_MASK		BIT(10)
+#define MT6370_FLED1STRB_MASK		BIT(9)
+#define MT6370_FLED2STRB_MASK		BIT(8)
+#define MT6370_FLED1SHORT_MASK		BIT(7)
+#define MT6370_FLED2SHORT_MASK		BIT(6)
+#define MT6370_FLEDLVF_MASK		BIT(3)
+
+#define MT6370_LED_JOINT		2
+#define MT6370_RANGE_FLED_REG		4
+#define MT6370_ITORCH_MIN_uA		25000
+#define MT6370_ITORCH_STEP_uA		12500
+#define MT6370_ITORCH_MAX_uA		400000
+#define MT6370_ITORCH_DOUBLE_MAX_uA	800000
+#define MT6370_ISTRB_MIN_uA		50000
+#define MT6370_ISTRB_STEP_uA		12500
+#define MT6370_ISTRB_MAX_uA		1500000
+#define MT6370_ISTRB_DOUBLE_MAX_uA	3000000
+#define MT6370_STRBTO_MIN_US		64000
+#define MT6370_STRBTO_STEP_US		32000
+#define MT6370_STRBTO_MAX_US		2432000
+
+#define to_mt6370_led(ptr, member) container_of(ptr, struct mt6370_led, member)
+
+struct mt6370_led {
+	struct led_classdev_flash flash;
+	struct v4l2_flash *v4l2_flash;
+	struct mt6370_priv *priv;
+	u8 led_no;
+};
+
+struct mt6370_priv {
+	struct regmap *regmap;
+	struct mutex lock;
+	unsigned int fled_strobe_used;
+	unsigned int fled_torch_used;
+	unsigned int leds_active;
+	unsigned int leds_count;
+	struct mt6370_led leds[];
+};
+
+static int mt6370_torch_brightness_set(struct led_classdev *lcdev, enum led_brightness level)
+{
+	struct mt6370_led *led = to_mt6370_led(lcdev, flash.led_cdev);
+	struct mt6370_priv *priv = led->priv;
+	u32 led_enable_mask = led->led_no == MT6370_LED_JOINT ? MT6370_FLCSEN_MASK_ALL :
+			      MT6370_FLCSEN_MASK(led->led_no);
+	u32 enable_mask = MT6370_TORCHEN_MASK | led_enable_mask;
+	u32 val = level ? led_enable_mask : 0;
+	u32 curr;
+	int ret, i;
+
+	mutex_lock(&priv->lock);
+
+	/*
+	 * There is only one set of flash control logic, and this flag is used to check if 'strobe'
+	 * is currently being used.
+	 */
+	if (priv->fled_strobe_used) {
+		dev_warn(lcdev->dev, "Please disable strobe first [%d]\n", priv->fled_strobe_used);
+		ret = -EBUSY;
+		goto unlock;
+	}
+
+	if (level)
+		curr = priv->fled_torch_used | BIT(led->led_no);
+	else
+		curr = priv->fled_torch_used & ~BIT(led->led_no);
+
+	if (curr)
+		val |= MT6370_TORCHEN_MASK;
+
+	if (level) {
+		level -= 1;
+		if (led->led_no == MT6370_LED_JOINT) {
+			u32 flevel[MT6370_MAX_LEDS];
+
+			/*
+			 * There're two flash channels in MT6370. If joint flash output is used,
+			 * torch current will be averaged output from both channels.
+			 */
+			flevel[0] = level / 2;
+			flevel[1] = level - flevel[0];
+			for (i = 0; i < MT6370_MAX_LEDS; i++) {
+				ret = regmap_update_bits(priv->regmap, MT6370_REG_FLEDITOR(i),
+							 MT6370_ITORCH_MASK, flevel[i]);
+				if (ret)
+					goto unlock;
+			}
+		} else {
+			ret = regmap_update_bits(priv->regmap, MT6370_REG_FLEDITOR(led->led_no),
+						 MT6370_ITORCH_MASK, level);
+			if (ret)
+				goto unlock;
+		}
+	}
+
+	ret = regmap_update_bits(priv->regmap, MT6370_REG_FLEDEN, enable_mask, val);
+	if (ret)
+		goto unlock;
+
+	priv->fled_torch_used = curr;
+
+unlock:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int mt6370_flash_brightness_set(struct led_classdev_flash *fl_cdev, u32 brightness)
+{
+	/*
+	 * Because of the current spikes when turning on the flash, the brightness should be kept
+	 * by the LED framework. This empty function is used to prevent checking failure when
+	 * led_classdev_flash registers ops.
+	 */
+	return 0;
+}
+
+static int _mt6370_flash_brightness_set(struct led_classdev_flash *fl_cdev, u32 brightness)
+{
+	struct mt6370_led *led = to_mt6370_led(fl_cdev, flash);
+	struct mt6370_priv *priv = led->priv;
+	struct led_flash_setting *setting = &fl_cdev->brightness;
+	u32 val = (brightness - setting->min) / setting->step;
+	int ret, i;
+
+	if (led->led_no == MT6370_LED_JOINT) {
+		u32 flevel[MT6370_MAX_LEDS];
+
+		/*
+		 * There're two flash channels in MT6370. If joint flash output is used, storbe
+		 * current will be averaged output from both channels.
+		 */
+		flevel[0] = val / 2;
+		flevel[1] = val - flevel[0];
+		for (i = 0; i < MT6370_MAX_LEDS; i++) {
+			ret = regmap_update_bits(priv->regmap, MT6370_REG_FLEDISTRB(i),
+						 MT6370_ISTROBE_MASK, flevel[i]);
+			if (ret)
+				break;
+		}
+	} else
+		ret = regmap_update_bits(priv->regmap, MT6370_REG_FLEDISTRB(led->led_no),
+					 MT6370_ISTROBE_MASK, val);
+
+	return ret;
+}
+
+static int mt6370_strobe_set(struct led_classdev_flash *fl_cdev, bool state)
+{
+	struct mt6370_led *led = to_mt6370_led(fl_cdev, flash);
+	struct mt6370_priv *priv = led->priv;
+	struct led_classdev *lcdev = &fl_cdev->led_cdev;
+	struct led_flash_setting *s = &fl_cdev->brightness;
+	u32 led_enable_mask = led->led_no == MT6370_LED_JOINT ? MT6370_FLCSEN_MASK_ALL :
+			      MT6370_FLCSEN_MASK(led->led_no);
+	u32 enable_mask = MT6370_STROBEN_MASK | led_enable_mask;
+	u32 val = state ? led_enable_mask : 0;
+	u32 curr;
+	int ret;
+
+	mutex_lock(&priv->lock);
+
+	/*
+	 * There is only one set of flash control logic, and this flag is used to check if 'torch'
+	 * is currently being used.
+	 */
+	if (priv->fled_torch_used) {
+		dev_warn(lcdev->dev, "Please disable torch first [0x%x]\n", priv->fled_torch_used);
+		ret = -EBUSY;
+		goto unlock;
+	}
+
+	if (state)
+		curr = priv->fled_strobe_used | BIT(led->led_no);
+	else
+		curr = priv->fled_strobe_used & ~BIT(led->led_no);
+
+	if (curr)
+		val |= MT6370_STROBEN_MASK;
+
+	ret = regmap_update_bits(priv->regmap, MT6370_REG_FLEDEN, enable_mask, val);
+	if (ret) {
+		dev_err(lcdev->dev, "[%d] control current source %d fail\n", led->led_no, state);
+		goto unlock;
+	}
+
+	/*
+	 * If the flash needs to turn on, configure the flash current to ramp up to the setting
+	 * value. Otherwise, always revert to the minimum one.
+	 */
+	ret = _mt6370_flash_brightness_set(fl_cdev, state ? s->val : s->min);
+	if (ret) {
+		dev_err(lcdev->dev, "[%d] Failed to set brightness\n", led->led_no);
+		goto unlock;
+	}
+
+	/*
+	 * For the flash to turn on/off, we must wait for HW ramping up/down time 5ms/500us to
+	 * prevent the unexpected problem.
+	 */
+	if (!priv->fled_strobe_used && curr)
+		usleep_range(5000, 6000);
+	else if (priv->fled_strobe_used && !curr)
+		usleep_range(500, 600);
+
+	priv->fled_strobe_used = curr;
+
+unlock:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int mt6370_strobe_get(struct led_classdev_flash *fl_cdev, bool *state)
+{
+	struct mt6370_led *led = to_mt6370_led(fl_cdev, flash);
+	struct mt6370_priv *priv = led->priv;
+
+	mutex_lock(&priv->lock);
+	*state = !!(priv->fled_strobe_used & BIT(led->led_no));
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
+static int mt6370_timeout_set(struct led_classdev_flash *fl_cdev, u32 timeout)
+{
+	struct mt6370_led *led = to_mt6370_led(fl_cdev, flash);
+	struct mt6370_priv *priv = led->priv;
+	struct led_flash_setting *s = &fl_cdev->timeout;
+	u32 val = (timeout - s->min) / s->step;
+
+	return regmap_update_bits(priv->regmap, MT6370_REG_STRBTO, MT6370_STRBTO_MASK, val);
+}
+
+static int mt6370_fault_get(struct led_classdev_flash *fl_cdev, u32 *fault)
+{
+	struct mt6370_led *led = to_mt6370_led(fl_cdev, flash);
+	struct mt6370_priv *priv = led->priv;
+	u16 fled_stat;
+	unsigned int chg_stat, strobe_timeout_mask, fled_short_mask;
+	u32 rfault = 0;
+	int ret;
+
+	ret = regmap_read(priv->regmap, MT6370_REG_CHGSTAT2, &chg_stat);
+	if (ret)
+		return ret;
+
+	ret = regmap_raw_read(priv->regmap, MT6370_REG_FLEDSTAT1, &fled_stat, sizeof(fled_stat));
+	if (ret)
+		return ret;
+
+	switch (led->led_no) {
+	case MT6370_LED_FLASH1:
+		strobe_timeout_mask = MT6370_FLED1STRBTO_MASK;
+		fled_short_mask = MT6370_FLED1SHORT_MASK;
+		break;
+
+	case MT6370_LED_FLASH2:
+		strobe_timeout_mask = MT6370_FLED2STRBTO_MASK;
+		fled_short_mask = MT6370_FLED2SHORT_MASK;
+		break;
+
+	case MT6370_LED_JOINT:
+		strobe_timeout_mask = MT6370_FLED1STRBTO_MASK | MT6370_FLED2STRBTO_MASK;
+		fled_short_mask = MT6370_FLED1SHORT_MASK | MT6370_FLED2SHORT_MASK;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (chg_stat & MT6370_FLEDCHGVINOVP_MASK)
+		rfault |= LED_FAULT_INPUT_VOLTAGE;
+
+	if (fled_stat & strobe_timeout_mask)
+		rfault |= LED_FAULT_TIMEOUT;
+
+	if (fled_stat & fled_short_mask)
+		rfault |= LED_FAULT_SHORT_CIRCUIT;
+
+	if (fled_stat & MT6370_FLEDLVF_MASK)
+		rfault |= LED_FAULT_UNDER_VOLTAGE;
+
+	*fault = rfault;
+	return ret;
+}
+
+static const struct led_flash_ops mt6370_flash_ops = {
+	.flash_brightness_set = mt6370_flash_brightness_set,
+	.strobe_set = mt6370_strobe_set,
+	.strobe_get = mt6370_strobe_get,
+	.timeout_set = mt6370_timeout_set,
+	.fault_get = mt6370_fault_get,
+};
+
+#if IS_ENABLED(CONFIG_V4L2_FLASH_LED_CLASS)
+static int mt6370_flash_external_strobe_set(struct v4l2_flash *v4l2_flash,
+					    bool enable)
+{
+	struct led_classdev_flash *flash = v4l2_flash->fled_cdev;
+	struct mt6370_led *led = to_mt6370_led(flash, flash);
+	struct mt6370_priv *priv = led->priv;
+	u32 mask = led->led_no == MT6370_LED_JOINT ? MT6370_FLCSEN_MASK_ALL :
+		   MT6370_FLCSEN_MASK(led->led_no);
+	u32 val = enable ? mask : 0;
+	int ret;
+
+	mutex_lock(&priv->lock);
+
+	ret = regmap_update_bits(priv->regmap, MT6370_REG_FLEDEN, mask, val);
+	if (ret)
+		goto unlock;
+
+	if (enable)
+		priv->fled_strobe_used |= BIT(led->led_no);
+	else
+		priv->fled_strobe_used &= ~BIT(led->led_no);
+
+unlock:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static const struct v4l2_flash_ops v4l2_flash_ops = {
+	.external_strobe_set = mt6370_flash_external_strobe_set,
+};
+
+static void mt6370_init_v4l2_flash_config(struct mt6370_led *led, struct v4l2_flash_config *cfg)
+{
+	struct led_classdev *lcdev;
+	struct led_flash_setting *s = &cfg->intensity;
+
+	lcdev = &led->flash.led_cdev;
+
+	s->min = MT6370_ITORCH_MIN_uA;
+	s->step = MT6370_ITORCH_STEP_uA;
+	s->val = s->max = s->min + (lcdev->max_brightness - 1) * s->step;
+
+	cfg->has_external_strobe = 1;
+	strscpy(cfg->dev_name, dev_name(lcdev->dev), sizeof(cfg->dev_name));
+
+	cfg->flash_faults = LED_FAULT_SHORT_CIRCUIT | LED_FAULT_TIMEOUT |
+			    LED_FAULT_INPUT_VOLTAGE | LED_FAULT_UNDER_VOLTAGE;
+}
+#else
+static const struct v4l2_flash_ops v4l2_flash_ops;
+static void mt6370_init_v4l2_flash_config(struct mt6370_led *led, struct v4l2_flash_config *cfg)
+{
+}
+#endif
+
+static void mt6370_v4l2_flash_release(void *v4l2_flash)
+{
+	v4l2_flash_release(v4l2_flash);
+}
+
+static int mt6370_led_register(struct device *parent, struct mt6370_led *led,
+			       struct fwnode_handle *fwnode)
+{
+	struct led_init_data init_data = { .fwnode = fwnode };
+	struct v4l2_flash_config v4l2_config = {};
+	int ret;
+
+	ret = devm_led_classdev_flash_register_ext(parent, &led->flash, &init_data);
+	if (ret)
+		return dev_err_probe(parent, ret, "Couldn't register flash %d\n", led->led_no);
+
+	mt6370_init_v4l2_flash_config(led, &v4l2_config);
+	led->v4l2_flash = v4l2_flash_init(parent, fwnode, &led->flash, &v4l2_flash_ops,
+					  &v4l2_config);
+	if (IS_ERR(led->v4l2_flash))
+		return dev_err_probe(parent, PTR_ERR(led->v4l2_flash),
+				     "Failed to register %d v4l2 sd\n", led->led_no);
+
+	return devm_add_action_or_reset(parent, mt6370_v4l2_flash_release, led->v4l2_flash);
+}
+
+static u32 mt6370_clamp(u32 val, u32 min, u32 max, u32 step)
+{
+	u32 retval;
+
+	retval = clamp_val(val, min, max);
+	if (step > 1)
+		retval = rounddown(retval - min, step) + min;
+
+	return retval;
+}
+
+static int mt6370_init_flash_properties(struct device *dev, struct mt6370_led *led,
+					struct fwnode_handle *fwnode)
+{
+	struct led_classdev_flash *flash = &led->flash;
+	struct led_classdev *lcdev = &flash->led_cdev;
+	struct mt6370_priv *priv = led->priv;
+	struct led_flash_setting *s;
+	u32 sources[MT6370_MAX_LEDS];
+	u32 max_ua, val;
+	int i, ret, num;
+
+	num = fwnode_property_count_u32(fwnode, "led-sources");
+	if (num < 1)
+		return dev_err_probe(dev, -EINVAL,
+				     "Not specified or wrong number of led-sources\n");
+
+	ret = fwnode_property_read_u32_array(fwnode, "led-sources", sources, num);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < num; i++) {
+		if (sources[i] >= MT6370_MAX_LEDS)
+			return -EINVAL;
+		if (priv->leds_active & BIT(sources[i]))
+			return -EINVAL;
+		priv->leds_active |= BIT(sources[i]);
+	}
+
+	/* If both channels are specified in 'led-sources', joint flash output mode is used */
+	led->led_no = num == 2 ? MT6370_LED_JOINT : sources[0];
+
+	max_ua = num == 2 ? MT6370_ITORCH_DOUBLE_MAX_uA : MT6370_ITORCH_MAX_uA;
+	val = MT6370_ITORCH_MIN_uA;
+	ret = fwnode_property_read_u32(fwnode, "led-max-microamp", &val);
+	if (!ret)
+		val = mt6370_clamp(val, MT6370_ITORCH_MIN_uA, max_ua, MT6370_ITORCH_STEP_uA);
+
+	lcdev->max_brightness = (val - MT6370_ITORCH_MIN_uA) / MT6370_ITORCH_STEP_uA + 1;
+	lcdev->brightness_set_blocking = mt6370_torch_brightness_set;
+	lcdev->flags |= LED_DEV_CAP_FLASH;
+
+	max_ua = num == 2 ? MT6370_ISTRB_DOUBLE_MAX_uA : MT6370_ISTRB_MAX_uA;
+	val = MT6370_ISTRB_MIN_uA;
+	ret = fwnode_property_read_u32(fwnode, "flash-max-microamp", &val);
+	if (!ret)
+		val = mt6370_clamp(val, MT6370_ISTRB_MIN_uA, max_ua, MT6370_ISTRB_STEP_uA);
+
+	s = &flash->brightness;
+	s->min = MT6370_ISTRB_MIN_uA;
+	s->step = MT6370_ISTRB_STEP_uA;
+	s->val = s->max = val;
+
+	/* Always configure to the minimum level when off to prevent flash current spikes. */
+	ret = _mt6370_flash_brightness_set(flash, s->min);
+	if (ret)
+		return ret;
+
+
+	val = MT6370_STRBTO_MIN_US;
+	ret = fwnode_property_read_u32(fwnode, "flash-max-timeout-us", &val);
+	if (!ret)
+		val = mt6370_clamp(val, MT6370_STRBTO_MIN_US, MT6370_STRBTO_MAX_US,
+				   MT6370_STRBTO_STEP_US);
+
+	s = &flash->timeout;
+	s->min = MT6370_STRBTO_MIN_US;
+	s->step = MT6370_STRBTO_STEP_US;
+	s->val = s->max = val;
+
+	flash->ops = &mt6370_flash_ops;
+
+	return 0;
+}
+
+static int mt6370_led_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct mt6370_priv *priv;
+	struct fwnode_handle *child;
+	size_t count;
+	int i = 0, ret;
+
+	count = device_get_child_node_count(dev);
+	if (!count || count > MT6370_MAX_LEDS)
+		return dev_err_probe(dev, -EINVAL,
+		       "No child node or node count over max led number %zu\n", count);
+
+	priv = devm_kzalloc(dev, struct_size(priv, leds, count), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->leds_count = count;
+	mutex_init(&priv->lock);
+
+	priv->regmap = dev_get_regmap(dev->parent, NULL);
+	if (!priv->regmap)
+		return dev_err_probe(dev, -ENODEV, "Failed to get parent regmap\n");
+
+	device_for_each_child_node(dev, child) {
+		struct mt6370_led *led = priv->leds + i;
+
+		led->priv = priv;
+
+		ret = mt6370_init_flash_properties(dev, led, child);
+		if (ret) {
+			fwnode_handle_put(child);
+			return ret;
+		}
+
+		ret = mt6370_led_register(dev, led, child);
+		if (ret) {
+			fwnode_handle_put(child);
+			return ret;
+		}
+
+		i++;
+	}
+
+	return 0;
+}
+
+static const struct of_device_id mt6370_led_of_id[] = {
+	{ .compatible = "mediatek,mt6370-flashlight" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, mt6370_led_of_id);
+
+static struct platform_driver mt6370_led_driver = {
+	.driver = {
+		.name = "mt6370-flashlight",
+		.of_match_table = mt6370_led_of_id,
+	},
+	.probe = mt6370_led_probe,
+};
+module_platform_driver(mt6370_led_driver);
+
+MODULE_AUTHOR("Alice Chen <alice_chen@xxxxxxxxxxx>");
+MODULE_AUTHOR("ChiYuan Huang <cy_huang@xxxxxxxxxxx>");
+MODULE_DESCRIPTION("MT6370 FLASH LED Driver");
+MODULE_LICENSE("GPL");
-- 
2.7.4




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux OMAP]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux