On Sat, Jul 25, 2020 at 11:34:50AM +0200, Marek Behun wrote:
> On Sat, 25 Jul 2020 11:23:39 +0200
> Pavel Machek <pavel@xxxxxx> wrote:
>
> > Hi!
> >
> > > +static const struct marvell_led_mode_info marvell_led_mode_info[] = {
> > > + { "link", { 0x0, -1, 0x0, -1, -1, -1, }, 0 },
> > > + { "link/act", { 0x1, 0x1, 0x1, 0x1, 0x1, 0x1, }, 0 },
> > > + { "1Gbps/100Mbps/10Mbps", { 0x2, -1, -1, -1, -1, -1, }, 0 },
> >
> > is this "1Gbps-10Mbps"?
>
> Most of these modes mean "ON on event", eg
> "link" means ON when link up, else OFF. "
> "tx" means ON on when transmitting, else OFF
> "act" means ON when activity, else OFF
> "copper" means ON when copper link up, else OFF
> but some are blinking modes
> "blink-act" means BLINK when activity, else OFF
>
> Some modes can do ON and BLINK, these have one '/' in their name
> "link/act" means ON when link up, BLINK on activity, else OFF
> "link/rx" means ON when link up, BLINK on receive, else OFF
>
> there is one mode, "1Gbps/100Mbps/10Mbps", which behaves differently:
> blinks 3 times when linked on 1Gbps
> blinks 2 times when linked on 100Mbps
> blinks 1 time when linked on 10Mbps
> (and this blinking is repeating, ie blinks 3 times, pause, blinks 3 times,
> pause)
>
> Some modes are disjunctive:
> "100Mbps-fiber" means ON when linked on 100Mbps or via fiber, else OFF
Hi Marek
I would be good to added this to the sysfs documentation.
> > > + { "act", { 0x3, 0x3, 0x3, 0x3, 0x3, 0x3, }, 0 },
> > > + { "blink-act", { 0x4, 0x4, 0x4, 0x4, 0x4, 0x4, }, 0 },
> > > + { "tx", { 0x5, -1, 0x5, -1, 0x5, 0x5, }, 0 },
> > > + { "tx", { -1, -1, -1, 0x5, -1, -1, }, L3V5_TRANS },
> > > + { "rx", { -1, -1, -1, -1, 0x0, 0x0, }, 0 },
> > > + { "rx", { -1, 0x0, -1, -1, -1, -1, }, L1V0_RECV },
To be consistent these four probably should have the blink- prefix. Or
it could be /tx, /rx ?
> > > + { "copper", { 0x6, -1, -1, -1, -1, -1, }, 0 },
> > > + { "copper", { -1, 0x0, -1, -1, -1, -1, }, L1V0_COPPER },
> > > + { "1Gbps", { 0x7, -1, -1, -1, -1, -1, }, 0 },
> > > + { "link/rx", { -1, 0x2, -1, 0x2, 0x2, 0x2, }, 0 },
> > > + { "100Mbps-fiber", { -1, 0x5, -1, -1, -1, -1, }, L1V5_100_FIBER },
> > > + { "100Mbps-10Mbps", { -1, 0x5, -1, -1, -1, -1, }, L1V5_100_10 },
> > > + { "1Gbps-100Mbps", { -1, 0x6, -1, -1, -1, -1, }, 0 },
> > > + { "1Gbps-10Mbps", { -1, -1, 0x6, 0x6, -1, -1, }, 0 },
> > > + { "100Mbps", { -1, 0x7, -1, -1, -1, -1, }, 0 },
> > > + { "10Mbps", { -1, -1, 0x7, -1, -1, -1, }, 0 },
> > > + { "fiber", { -1, -1, -1, 0x0, -1, -1, }, L3V0_FIBER },
> > > + { "fiber", { -1, -1, -1, 0x7, -1, -1, }, L3V7_FIBER },
> > > + { "FullDuplex", { -1, -1, -1, 0x7, -1, -1, }, L3V7_DUPLEX },
> > > + { "FullDuplex", { -1, -1, -1, -1, 0x6, 0x6, }, 0 },
> > > + { "FullDuplex/collision", { -1, -1, -1, -1, 0x7, 0x7, }, 0 },
> > > + { "FullDuplex/collision", { -1, -1, 0x2, -1, -1, -1, }, L2V2_DUPLEX },
> > > + { "ptp", { -1, -1, 0x2, -1, -1, -1, }, L2V2_PTP },
> > > + { "init", { -1, -1, 0x2, -1, -1, -1, }, L2V2_INIT },
> > > + { "los", { -1, -1, -1, 0x0, -1, -1, }, L3V0_LOS },
> > > + { "hi-z", { 0xa, 0xa, 0xa, 0xa, 0xa, 0xa, }, 0 },
> > > + { "blink", { 0xb, 0xb, 0xb, 0xb, 0xb, 0xb, }, 0 },
> > > +};
> >
> > Certainly more documentation will be required here, what "ptp" setting
> > does, for example, is not very obvious to me.
>
> "ptp" means it will light up when the PTP functionality is enabled on
> the PHY and a PTP packet is received.
Does hi-z mean off? In the implementation i did, i did not list off
and on as triggers. I instead used them for untriggered
brightness. That allowed the software triggers to work, so i had the
PHY blinking the heartbeat etc. But i had to make it optional, since a
quick survey of datasheets suggested not all PHYs support simple
on/off control.
Something beyond the scope of this patchset is implementing etHool -p
-p --identify
Initiates adapter-specific action intended to enable an operator to
easily identify the adapter by sight. Typically this involves blink‐
ing one or more LEDs on the specific network port.
If we have software controlled on/off, then a software trigger seems
like i good way to do this.
Andrew
