On 6/22/20 12:54 PM, Jacek Anaszewski wrote:
Hi Vishwanatha,
On 6/22/20 8:58 AM, Vishwanatha Subbanna wrote:
Thank you very much Jacek.
On 22-Jun-2020, at 3:12 AM, Jacek Anaszewski
<jacek.anaszewski@xxxxxxxxx> wrote:
Hi Vishwanatha,
On 6/20/20 7:25 PM, Vishwanatha Subbanna wrote:
Hi Jacek,
Thank you very much for the quick response. Greatly appreciate that.
You're welcome.
On 20-Jun-2020, at 3:27 AM, Jacek Anaszewski
<jacek.anaszewski@xxxxxxxxx> wrote:
Hi Vishwanatha,
Please refer to
Documentation/devicetree/bindings/leds/leds-pca955x.txt.
At first glance I don't get why you have gpio-leds node, which is for
leds-gpio driver.
Not sure I understood it right.. But if you are asking me why I have
"leds {" and “gpio-leds” in there, then it is to get the entries in
/sys/class/leds.
The GPIOs from PCA9552 are connected to LED. Also, that is how we
have had in the past, and that worked.
Example:
https://github.com/openbmc/linux/blob/dev-5.4/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts#L115
Thanks. Yeah, that looks OK, I had to take closer look at the driver.
The problem I am running into is for :
https://github.com/openbmc/linux/blob/dev-5.4/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
On 6/19/20 3:34 PM, Vishwanatha Subbanna wrote:
Hello,
I am Vishwanath, working with IBM and looking for your help on one
of the issues that I am running into. Would really appreciate help
on this. I run Linux 5.4.38
I have 2 number of PCA9552 chips, one on the Planar and other on
the card that is optionally pluggable. The optional card must be
plugged prior to booting and is not hot pluggable. In my
experiment, I am running *without* the optional card plugged in.
In the device tree, I have a "leds {" section that looks like
below for the PCA9552 that is on the planar and everything works
fine and I can see /sys/class/leds/fan0
leds {
compatible = "gpio-leds”;
fan0 {
retain-state-shutdown;
default-state = "keep";
gpios = <&pca0 0 GPIO_ACTIVE_LOW>;
};
};
&i2c7 {
status = "okay”;
pca0: pca9552@61 {
compatible = "nxp,pca9552";
reg = <0x61>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio@0 {
reg = <0>;
type = <PCA955X_TYPE_GPIO>;
};
};
};
Similarly, if I update the device tree entry for PCA9552 for the
card that is optionally pluggable, then I don’t see any leds
entries in /sys/class/leds.
Please share your DT node after the update.
Pasting the GPIO_0 entry only here for brevity.
leds {
compatible = "gpio-leds”;
fan0 {
retain-state-shutdown;
default-state = "keep";
gpios = <&pca0 0 GPIO_ACTIVE_LOW>;
};
nvmeslot0 {
retain-state-shutdown;
default-state = "keep";
gpios = <&pca1 0 GPIO_ACTIVE_LOW>;
};
};
&i2c7 {
status = "okay”;
pca0: pca9552@61 {
compatible = "nxp,pca9552";
reg = <0x61>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio@0 {
reg = <0>;
type = <PCA955X_TYPE_GPIO>;
};
};
};
&i2c13
{
pca1: pca9552@60 {
compatible = "nxp,pca9552";
reg = <0x60>;
#address-cells = <1>;
#size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio@0 {
reg = <0>;
type = <PCA955X_TYPE_GPIO>;
};
};
};
Thanks
!! Vishwa !!
I don’t even see “fan0” that is on the PCA9552 on planar also. I
was expecting that I should see “/sys/class/leds/fan0”.
However, I could see all the entries in “/proc/device-tree/leds”.
Data from the failure.
[ 7.895757] leds-pca955x 7-0061: leds-pca955x: Using pca9552
16-bit LED driver at slave address 0x61
[ 7.907659] leds-pca955x 7-0061: gpios 168...183
It is weird that you don't see "fan0" LED since this gpio seems to have
been properly registered according to this log.
This is exactly what I don’t understand. I would expect “fan0” to
appear in /sys/class/leds. Is there any reason why this might not be
appearing ?..
OK, now the reason is clear to me. If leds-gpio driver fails to register
any of the LEDs found in DT node it returns with an error from the
probe(), which results in unregistering any of the LEDs registered in
the previous iteration steps.
Look at the function gpio_leds_create() in
drivers/leds/leds-gpio.c.
Probably it is devm_fwnode_get_gpiod_from_child() that fails
while parsing nvmeslot0 node.
IOW you have to have two separate dts files for the arrangement
with the card and without it.
--
Best regards,
Jacek Anaszewski
