The test patterns are almost same in three sequential tests. Make the unified helper function for improving the readability. Link: https://lore.kernel.org/all/20210127154939.13288-1-tiwai@xxxxxxx/ Signed-off-by: Takashi Iwai <tiwai@xxxxxxx> --- .../selftests/firmware/fw_filesystem.sh | 106 +++++------------- 1 file changed, 30 insertions(+), 76 deletions(-) diff --git a/tools/testing/selftests/firmware/fw_filesystem.sh b/tools/testing/selftests/firmware/fw_filesystem.sh index 3ac09b401a83..4a574be8b862 100755 --- a/tools/testing/selftests/firmware/fw_filesystem.sh +++ b/tools/testing/selftests/firmware/fw_filesystem.sh @@ -437,6 +437,32 @@ test_request_partial_firmware_into_buf() echo "OK" } +do_tests () +{ + mode="$1" + suffix="$2" + + for i in $(seq 1 5); do + test_batched_request_firmware$suffix $i $mode + done + + for i in $(seq 1 5); do + test_batched_request_firmware_into_buf$suffix $i $mode + done + + for i in $(seq 1 5); do + test_batched_request_firmware_direct$suffix $i $mode + done + + for i in $(seq 1 5); do + test_request_firmware_nowait_uevent$suffix $i $mode + done + + for i in $(seq 1 5); do + test_request_firmware_nowait_custom$suffix $i $mode + done +} + # Only continue if batched request triggers are present on the # test-firmware driver test_config_present @@ -444,25 +470,7 @@ test_config_present # test with the file present echo echo "Testing with the file present..." -for i in $(seq 1 5); do - test_batched_request_firmware $i normal -done - -for i in $(seq 1 5); do - test_batched_request_firmware_into_buf $i normal -done - -for i in $(seq 1 5); do - test_batched_request_firmware_direct $i normal -done - -for i in $(seq 1 5); do - test_request_firmware_nowait_uevent $i normal -done - -for i in $(seq 1 5); do - test_request_firmware_nowait_custom $i normal -done +do_tests normal # Partial loads cannot use fallback, so do not repeat tests. test_request_partial_firmware_into_buf 0 10 @@ -474,25 +482,7 @@ test_request_partial_firmware_into_buf 2 10 # a hung task, which would require a hard reset. echo echo "Testing with the file missing..." -for i in $(seq 1 5); do - test_batched_request_firmware_nofile $i -done - -for i in $(seq 1 5); do - test_batched_request_firmware_into_buf_nofile $i -done - -for i in $(seq 1 5); do - test_batched_request_firmware_direct_nofile $i -done - -for i in $(seq 1 5); do - test_request_firmware_nowait_uevent_nofile $i -done - -for i in $(seq 1 5); do - test_request_firmware_nowait_custom_nofile $i -done +do_tests nofile _nofile # Partial loads cannot use fallback, so do not repeat tests. test_request_partial_firmware_into_buf_nofile 0 10 @@ -508,49 +498,13 @@ $RUN_XZ -k $FW_INTO_BUF config_set_name $NAME echo echo "Testing with both plain and xz files present..." -for i in $(seq 1 5); do - test_batched_request_firmware $i both -done - -for i in $(seq 1 5); do - test_batched_request_firmware_into_buf $i both -done - -for i in $(seq 1 5); do - test_batched_request_firmware_direct $i both -done - -for i in $(seq 1 5); do - test_request_firmware_nowait_uevent $i both -done - -for i in $(seq 1 5); do - test_request_firmware_nowait_custom $i both -done +do_tests both # test with only xz file present mv "$FW" "${FW}-orig" mv "$FW_INTO_BUF" "${FW_INTO_BUF}-orig" echo echo "Testing with only xz file present..." -for i in $(seq 1 5); do - test_batched_request_firmware $i xzonly -done - -for i in $(seq 1 5); do - test_batched_request_firmware_into_buf $i xzonly -done - -for i in $(seq 1 5); do - test_batched_request_firmware_direct $i xzonly -done - -for i in $(seq 1 5); do - test_request_firmware_nowait_uevent $i xzonly -done - -for i in $(seq 1 5); do - test_request_firmware_nowait_custom $i xzonly -done +do_tests xzonly exit 0 -- 2.31.1
