The commit bf4289cba02b8cf770ecd7959ca70839f0dd9d3c removed the use of CONFIG_MTD_NAND_ATMEL_ECC_NONE and CONFIG_MTD_NAND_ATMEL_ECC_HW but the Kconfig file was forgotten. This patch remove those inoperative options. Signed-off-by: Richard Genoud <richard.genoud@xxxxxxxxx> --- arch/arm/configs/afeb9260_defconfig | 1 - arch/arm/configs/at91sam9263_defconfig | 1 - arch/arm/configs/qil-a9260_defconfig | 1 - arch/arm/configs/usb-a9260_defconfig | 1 - drivers/mtd/nand/Kconfig | 40 -------------------------------- 5 files changed, 0 insertions(+), 44 deletions(-) diff --git a/arch/arm/configs/afeb9260_defconfig b/arch/arm/configs/afeb9260_defconfig index 2afdf67..c285a9d 100644 --- a/arch/arm/configs/afeb9260_defconfig +++ b/arch/arm/configs/afeb9260_defconfig @@ -39,7 +39,6 @@ CONFIG_MTD_BLOCK=y CONFIG_MTD_DATAFLASH=y CONFIG_MTD_NAND=y CONFIG_MTD_NAND_ATMEL=y -CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_SIZE=8192 CONFIG_ATMEL_SSC=y diff --git a/arch/arm/configs/at91sam9263_defconfig b/arch/arm/configs/at91sam9263_defconfig index 1cf9626..585e7e0 100644 --- a/arch/arm/configs/at91sam9263_defconfig +++ b/arch/arm/configs/at91sam9263_defconfig @@ -61,7 +61,6 @@ CONFIG_MTD_DATAFLASH=y CONFIG_MTD_BLOCK2MTD=y CONFIG_MTD_NAND=y CONFIG_MTD_NAND_ATMEL=y -CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y CONFIG_MTD_UBI=y CONFIG_MTD_UBI_GLUEBI=y CONFIG_BLK_DEV_LOOP=y diff --git a/arch/arm/configs/qil-a9260_defconfig b/arch/arm/configs/qil-a9260_defconfig index 9160f3b..2bb100b 100644 --- a/arch/arm/configs/qil-a9260_defconfig +++ b/arch/arm/configs/qil-a9260_defconfig @@ -50,7 +50,6 @@ CONFIG_MTD_BLOCK=y CONFIG_MTD_DATAFLASH=y CONFIG_MTD_NAND=y CONFIG_MTD_NAND_ATMEL=y -CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y CONFIG_BLK_DEV_LOOP=y # CONFIG_MISC_DEVICES is not set CONFIG_SCSI=y diff --git a/arch/arm/configs/usb-a9260_defconfig b/arch/arm/configs/usb-a9260_defconfig index 2e39f38..a1501e1 100644 --- a/arch/arm/configs/usb-a9260_defconfig +++ b/arch/arm/configs/usb-a9260_defconfig @@ -49,7 +49,6 @@ CONFIG_MTD_BLOCK=y CONFIG_MTD_DATAFLASH=y CONFIG_MTD_NAND=y CONFIG_MTD_NAND_ATMEL=y -CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y CONFIG_BLK_DEV_LOOP=y # CONFIG_MISC_DEVICES is not set CONFIG_SCSI=y diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index 31bb7e5..0d93407 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -406,46 +406,6 @@ config MTD_NAND_ATMEL help Enables support for NAND Flash / Smart Media Card interface on Atmel AT91 and AVR32 processors. -choice - prompt "ECC management for NAND Flash / SmartMedia on AT91 / AVR32" - depends on MTD_NAND_ATMEL - -config MTD_NAND_ATMEL_ECC_HW - bool "Hardware ECC" - depends on ARCH_AT91SAM9263 || ARCH_AT91SAM9260 || AVR32 - help - Use hardware ECC instead of software ECC when the chip - supports it. - - The hardware ECC controller is capable of single bit error - correction and 2-bit random detection per page. - - NB : hardware and software ECC schemes are incompatible. - If you switch from one to another, you'll have to erase your - mtd partition. - - If unsure, say Y - -config MTD_NAND_ATMEL_ECC_SOFT - bool "Software ECC" - help - Use software ECC. - - NB : hardware and software ECC schemes are incompatible. - If you switch from one to another, you'll have to erase your - mtd partition. - -config MTD_NAND_ATMEL_ECC_NONE - bool "No ECC (testing only, DANGEROUS)" - depends on DEBUG_KERNEL - help - No ECC will be used. - It's not a good idea and it should be reserved for testing - purpose only. - - If unsure, say N - -endchoice config MTD_NAND_PXA3xx tristate "Support for NAND flash devices on PXA3xx" -- 1.7.2.5 -- To unsubscribe from this list: send the line "unsubscribe kernel-janitors" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
