On 08/11/2023 16:56, Jiri Valek - 2N wrote: > Add support for advanced sensitivity settings and signal guard feature. > > Signed-off-by: Jiri Valek - 2N <jiriv@xxxxxxxx> > --- > .../bindings/input/microchip,cap11xx.yaml | 76 ++++++++++++++++++- > 1 file changed, 73 insertions(+), 3 deletions(-) > > diff --git a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml > index 5b5d4f7d3482..aa97702c43ef 100644 > --- a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml > +++ b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml > @@ -45,13 +45,13 @@ properties: > Enables the Linux input system's autorepeat feature on the input device. > > linux,keycodes: > - minItems: 6 > - maxItems: 6 > + minItems: 3 > + maxItems: 8 > description: | > Specifies an array of numeric keycode values to > be used for the channels. If this property is > omitted, KEY_A, KEY_B, etc are used as defaults. > - The array must have exactly six entries. > + The number of entries must correspond to the number of channels. > > microchip,sensor-gain: > $ref: /schemas/types.yaml#/definitions/uint32 > @@ -70,6 +70,55 @@ properties: > open drain. This property allows using the active > high push-pull output. > > + microchip,sensitivity-delta-sense: > + $ref: /schemas/types.yaml#/definitions/uint32 > + default: 32 > + enum: [1, 2, 4, 8, 16, 32, 64, 128] > + description: > + Optional parameter. Controls the sensitivity multiplier of a touch detection. > + At the more sensitive settings, touches are detected for a smaller delta Which values are more sensitive? > + capacitance corresponding to a “lighter” touch. Looks like you use some non-ASCII characters for ". > + > + microchip,signal-guard: > + $ref: /schemas/types.yaml#/definitions/uint32-array > + minItems: 3 > + maxItems: 8 > + items: > + minimum: 0 > + maximum: 1 > + description: | > + Optional parameter supported only for CAP129x. > + 0 - off > + 1 - on > + The signal guard isolates the signal from virtual grounds. > + If enabled then the behavior of the channel is changed to signal guard. > + The number of entries must correspond to the number of channels. > + > + microchip,input-treshold: typo: threshold > + $ref: /schemas/types.yaml#/definitions/uint32-array > + minItems: 3 > + maxItems: 8 > + items: > + minimum: 0 > + maximum: 127 > + description: > + Optional parameter. Specifies the delta threshold that is used to Drop everywhere the "optional parameter". It's redundant. required: block tells what is / is not optional. > + determine if a touch has been detected. In what units are the values? > + The number of entries must correspond to the number of channels. > + > + microchip,calib-sensitivity: > + $ref: /schemas/types.yaml#/definitions/uint32-array > + minItems: 3 > + maxItems: 8 > + items: > + minimum: 1 > + maximum: 4 > + description: > + Optional parameter supported only for CAP129x. Specifies an array of > + numeric values that controls the gain used by the calibration routine to > + enable sensor inputs to be more sensitive for proximity detection. Gain is usually in dB, isn't it? > + The number of entries must correspond to the number of channels. > + > patternProperties: > "^led@[0-7]$": Best regards, Krzysztof
