Re: [PATCH 2/5] Input: add driver for Focaltech FTS touchscreen

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Joel,

Some comments about the driver below,

On 3/12/23 11:32, Joel Selvaraj wrote:
The Focaltech FTS driver supports several variants of focaltech
touchscreens found in ~2018 era smartphones including variants found on
the PocoPhone F1 and the SHIFT6mq which are already present in mainline.
This driver is loosely based on the original driver from Focaltech
but has been simplified and largely reworked.

Co-developed-by: Caleb Connolly <caleb@xxxxxxxxxxxxx>
Signed-off-by: Caleb Connolly <caleb@xxxxxxxxxxxxx>
Signed-off-by: Joel Selvaraj <joelselvaraj.oss@xxxxxxxxx>
---
  MAINTAINERS                               |   8 +
  drivers/input/touchscreen/Kconfig         |  12 +
  drivers/input/touchscreen/Makefile        |   1 +
  drivers/input/touchscreen/focaltech_fts.c | 448 ++++++++++++++++++++++
  4 files changed, 469 insertions(+)
  create mode 100644 drivers/input/touchscreen/focaltech_fts.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 2892858cb040..deb561c356f2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7993,6 +7993,14 @@ L:	linux-input@xxxxxxxxxxxxxxx
  S:	Maintained
  F:	drivers/input/joystick/fsia6b.c
+FOCALTECH FTS TOUCHSCREEN DRIVER
+M:	Joel Selvaraj <joelselvaraj.oss@xxxxxxxxx>
+M:	Caleb Connolly <caleb@xxxxxxxxxxxxx>
+L:	linux-input@xxxxxxxxxxxxxxx
+S:	Maintained
+F:	Documentation/devicetree/bindings/input/touchscreen/focaltech,fts.yaml
+F:	drivers/input/touchscreen/focaltech_fts.c
+
  FOCUSRITE SCARLETT GEN 2/3 MIXER DRIVER
  M:	Geoffrey D. Bennett <g@xxxxx>
  L:	alsa-devel@xxxxxxxxxxxxxxxx (moderated for non-subscribers)
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 1a2049b336a6..320925bac3a1 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -388,6 +388,18 @@ config TOUCHSCREEN_EXC3000
  	  To compile this driver as a module, choose M here: the
  	  module will be called exc3000.
+config TOUCHSCREEN_FOCALTECH_FTS
+	tristate "Focaltech FTS Touchscreen"
+	depends on I2C
+	help
+	  Say Y here to enable support for I2C connected Focaltech FTS
+	  based touch panels, including the 5452 and 8917 panels.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called focaltech_fts.
+
  config TOUCHSCREEN_FUJITSU
  	tristate "Fujitsu serial touchscreen"
  	select SERIO
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index f2fd28cc34a6..83ea2e3ce754 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -45,6 +45,7 @@ obj-$(CONFIG_TOUCHSCREEN_ELO)		+= elo.o
  obj-$(CONFIG_TOUCHSCREEN_EGALAX)	+= egalax_ts.o
  obj-$(CONFIG_TOUCHSCREEN_EGALAX_SERIAL)	+= egalax_ts_serial.o
  obj-$(CONFIG_TOUCHSCREEN_EXC3000)	+= exc3000.o
+obj-$(CONFIG_TOUCHSCREEN_FOCALTECH_FTS)	+= focaltech_fts.o
  obj-$(CONFIG_TOUCHSCREEN_FUJITSU)	+= fujitsu_ts.o
  obj-$(CONFIG_TOUCHSCREEN_GOODIX)	+= goodix_ts.o
  obj-$(CONFIG_TOUCHSCREEN_HIDEEP)	+= hideep.o
diff --git a/drivers/input/touchscreen/focaltech_fts.c b/drivers/input/touchscreen/focaltech_fts.c
new file mode 100644
index 000000000000..d389c8b88944
--- /dev/null
+++ b/drivers/input/touchscreen/focaltech_fts.c
@@ -0,0 +1,448 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * FocalTech touchscreen driver.
+ *
+ * Copyright (c) 2010-2017, FocalTech Systems, Ltd., all rights reserved.
+ * Copyright (C) 2018 XiaoMi, Inc.
+ * Copyright (c) 2021 Caleb Connolly <caleb@xxxxxxxxxxxxx>
+ * Copyright (c) 2023 Joel Selvaraj <joelselvaraj.oss@xxxxxxxxx>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/input/touchscreen.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/i2c.h>
+#include <linux/regulator/consumer.h>
+#include <linux/delay.h>
+#include <linux/regmap.h>
+#include <linux/mutex.h>
Includes must be sorted alphabetically.
+
+#define FTS_REG_CHIP_ID_H 0xA3
+#define FTS_REG_CHIP_ID_L 0x9F
+
+#define FTS_MAX_POINTS_SUPPORT 10
+#define FTS_ONE_TOUCH_LEN 6
+
+#define FTS_TOUCH_X_H_OFFSET 3
+#define FTS_TOUCH_X_L_OFFSET 4
+#define FTS_TOUCH_Y_H_OFFSET 5
+#define FTS_TOUCH_Y_L_OFFSET 6
+#define FTS_TOUCH_PRESSURE_OFFSET 7
+#define FTS_TOUCH_AREA_OFFSET 8
+#define FTS_TOUCH_TYPE_OFFSET 3
+#define FTS_TOUCH_ID_OFFSET 5
+
+#define FTS_TOUCH_DOWN 0
+#define FTS_TOUCH_UP 1
+#define FTS_TOUCH_CONTACT 2
+
+#define FTS_DRIVER_NAME "fts-i2c"
+#define INTERVAL_READ_REG 100 /* unit:ms */
+#define TIMEOUT_READ_REG 2000 /* unit:ms */
Instead of using those comments, it's better to use the _MS suffix.
+
+#define CHIP_TYPE_5452 0x5452
+#define CHIP_TYPE_8719 0x8719
+
+struct fts_ts_data {
+	struct i2c_client *client;
+	struct input_dev *input_dev;
+	struct touchscreen_properties prop;
+
+	struct regmap *regmap;
+	int irq;
+
+	struct regulator_bulk_data regulators[2];
+
+	/* Touch data */
+	u8 max_touch_number;
+	u8 *point_buf;
+	int point_buf_size;
+
+	/* DT data */
+	struct gpio_desc *reset_gpio;
+};
+
+static const struct regmap_config fts_ts_i2c_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+};
+
+static bool fts_chip_is_valid(struct fts_ts_data *data, u16 id)
+{
+	if (id != CHIP_TYPE_5452 && id != CHIP_TYPE_8719)
+		return false;
+
+	return true;
+}
+
+int fts_check_status(struct fts_ts_data *data)
+{
+	int count = 0;
+	unsigned int val, id;
+
+	do {
+		regmap_read(data->regmap, FTS_REG_CHIP_ID_H, &val);
+		id = val << 8;
+		regmap_read(data->regmap, FTS_REG_CHIP_ID_L, &val);
+		id |= val;
That register layout is surely... weird. Anyway, I'd probably do
```
        regmap_read(data->regmap, FTS_REG_CHIP_ID_L, &id);
        regmap_read(data->regmap, FTS_REG_CHIP_ID_H, &val);
        id |= val << 8;
```
to make it less actions. Also, this lacks error checking for the regmap calls.
+
+		if (fts_chip_is_valid(data, id)) {
+			dev_dbg(&data->client->dev, "TS Ready: Chip ID = 0x%x", id);
+			return 0;
+		}
+
+		count++;
+		msleep(INTERVAL_READ_REG);
+	} while ((count * INTERVAL_READ_REG) < TIMEOUT_READ_REG);
+
+	return -EIO;
+}
+
+static void fts_report_touch(struct fts_ts_data *data)
+{
+	struct input_dev *input_dev = data->input_dev;
+	int base;
+	unsigned int x, y, z, maj;
+	u8 slot, type;
+	int error, i = 0;
+
+	u8 *buf = data->point_buf;
+
+	memset(buf, 0, data->point_buf_size);
+
+	error = regmap_bulk_read(data->regmap, 0, buf, data->point_buf_size);
+	if (error) {
+		dev_err_ratelimited(&data->client->dev, "I2C read failed: %d\n",
+				    error);
Why is the _ratelimited variant necessary?
+		return;
+	}
+
+	for (i = 0; i < data->max_touch_number; i++) {
+		base = FTS_ONE_TOUCH_LEN * i;
+
+		slot = (buf[base + FTS_TOUCH_ID_OFFSET]) >> 4;
I believe parentheses aren't needed?
+		if (slot >= data->max_touch_number)
+			break;
+
+		x = ((buf[base + FTS_TOUCH_X_H_OFFSET] & 0x0F) << 8) +
+			 (buf[base + FTS_TOUCH_X_L_OFFSET] & 0xFF);
+		y = ((buf[base + FTS_TOUCH_Y_H_OFFSET] & 0x0F) << 8) +
+			 (buf[base + FTS_TOUCH_Y_L_OFFSET] & 0xFF);
+
+		z = buf[base + FTS_TOUCH_PRESSURE_OFFSET];
+		if (z <= 0)
+			z = 0x3f;
+
+		maj = buf[base + FTS_TOUCH_AREA_OFFSET] >> 4;
+		if (maj <= 0)
+			maj = 0x09;
+
+		type = buf[base + FTS_TOUCH_TYPE_OFFSET] >> 6;
+
+		input_mt_slot(input_dev, slot);
+		if (type == FTS_TOUCH_DOWN || type == FTS_TOUCH_CONTACT) {
+			input_mt_report_slot_state(input_dev, MT_TOOL_FINGER, true);
+			touchscreen_report_pos(data->input_dev, &data->prop, x, y, true);
+			input_report_abs(input_dev, ABS_MT_PRESSURE, z);
+			input_report_abs(input_dev, ABS_MT_TOUCH_MAJOR, maj);
+			input_report_key(data->input_dev, BTN_TOUCH, 1);
+		} else {
+			input_report_key(data->input_dev, BTN_TOUCH, 0);
+			input_mt_report_slot_inactive(input_dev);
+		}
+	}
Overall, I think it's better to cast the data type to a struct, which would make this seem with less random.
+	input_sync(input_dev);
+}
+
+static irqreturn_t fts_ts_interrupt(int irq, void *dev_id)
+{
+	struct fts_ts_data *data = dev_id;
+
+	fts_report_touch(data);
+
+	return IRQ_HANDLED;
+}
+
+static void fts_power_off(void *d)
+{
+	struct fts_ts_data *data = d;
+
+	regulator_bulk_disable(ARRAY_SIZE(data->regulators),
+			       data->regulators);
+}
+
+static int fts_start(struct fts_ts_data *data)
+{
+	int error;
+
+	error = regulator_bulk_enable(ARRAY_SIZE(data->regulators),
+				      data->regulators);
+	if (error) {
+		dev_err(&data->client->dev, "failed to enable regulators\n");
+		return error;
+	}
+
+	gpiod_set_value_cansleep(data->reset_gpio, 0);
+	msleep(200);
+
+	enable_irq(data->irq);
+
+	return 0;
+}
+
+static int fts_stop(struct fts_ts_data *data)
+{
+	disable_irq(data->irq);
+	gpiod_set_value_cansleep(data->reset_gpio, 1);
+	fts_power_off(data);
+
+	return 0;
+}
+
+static int fts_input_open(struct input_dev *dev)
+{
+	struct fts_ts_data *data = input_get_drvdata(dev);
+	int error;
+
+	error = fts_start(data);
+	if (error)
+		return error;
+
+	error = fts_check_status(data);
+	if (error) {
+		dev_err(&data->client->dev, "Failed to start or unsupported chip");
+		return error;
+	}
+
+	return 0;
+}
+
+static void fts_input_close(struct input_dev *dev)
+{
+	struct fts_ts_data *data = input_get_drvdata(dev);
+
+	fts_stop(data);
+}
+
+static int fts_input_init(struct fts_ts_data *data)
+{
+	struct device *dev = &data->client->dev;
+	struct input_dev *input_dev;
+	int error = 0;
+
+	input_dev = devm_input_allocate_device(dev);
+	if (!input_dev)
+		return -ENOMEM;
+
+	data->input_dev = input_dev;
+
+	/* Init and register Input device */
+	input_dev->name = FTS_DRIVER_NAME;
+	input_dev->id.bustype = BUS_I2C;
+	input_dev->dev.parent = dev;
+	input_dev->open = fts_input_open;
+	input_dev->close = fts_input_close;
+
+	input_set_drvdata(input_dev, data);
+
+	__set_bit(EV_SYN, input_dev->evbit);
+	__set_bit(EV_ABS, input_dev->evbit);
+	__set_bit(INPUT_PROP_DIRECT, input_dev->propbit);
+
+	input_mt_init_slots(input_dev, data->max_touch_number,
+			    INPUT_MT_DIRECT);
+	input_set_capability(input_dev, EV_ABS, ABS_MT_POSITION_X);
+	input_set_capability(input_dev, EV_ABS, ABS_MT_POSITION_Y);
+	input_set_abs_params(input_dev, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0);
+	input_set_abs_params(input_dev, ABS_MT_PRESSURE, 0, 255, 0, 0);
+
+	touchscreen_parse_properties(input_dev, true, &data->prop);
+	if (!data->prop.max_x || !data->prop.max_y) {
+		dev_err(dev,
+			"touchscreen-size-x and/or touchscreen-size-y not set in dts\n");
+		return -EINVAL;
+	}
+
+	data->point_buf_size = (data->max_touch_number * FTS_ONE_TOUCH_LEN) + 3;
+	data->point_buf = devm_kzalloc(dev, data->point_buf_size, GFP_KERNEL);
+	if (!data->point_buf) {
+		dev_err(dev, "Failed to alloc memory for point buffer\n");
+		return -ENOMEM;
+	}
+
+	error = input_register_device(input_dev);
+	if (error) {
+		dev_err(dev, "Failed to register input device\n");
+		return error;
+	}
+
+	return 0;
+}
+
+static int fts_parse_dt(struct fts_ts_data *data)
+{
+	int error = 0;
+	struct device *dev = &data->client->dev;
+	struct device_node *np = dev->of_node;
+	u32 val;
+
+	error = of_property_read_u32(np, "focaltech,max-touch-number", &val);
+	if (error) {
+		dev_err(dev, "Unable to read property 'focaltech,max-touch-number'");
+		return -EINVAL;
+	}
+	if (val < 2 || val > FTS_MAX_POINTS_SUPPORT) {
+		dev_err(dev, "'focaltech,max-touch-number' out of range [2, %d]",
+			FTS_MAX_POINTS_SUPPORT);
+		return -EINVAL;
+	}
+	data->max_touch_number = val;
+
+	data->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(data->reset_gpio)) {
+		error = PTR_ERR(data->reset_gpio);
+		dev_err(dev, "Failed to request reset gpio, error %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int fts_ts_probe(struct i2c_client *client)
+{
+	int error = 0;
+	struct fts_ts_data *data;
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+		dev_err(&client->dev, "I2C not supported");
+		return -ENODEV;
+	}
+
+	if (!client->irq) {
+		dev_err(&client->dev, "No irq specified\n");
+		return -EINVAL;
+	}
+
+	data = devm_kzalloc(&client->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->client = client;
+
+	error = fts_parse_dt(data);
+	if (error)
+		return error;
+
+	i2c_set_clientdata(client, data);
+
+	data->regmap = devm_regmap_init_i2c(client, &fts_ts_i2c_regmap_config);
+	if (IS_ERR(data->regmap)) {
+		dev_err(&client->dev, "regmap allocation failed\n");
+		return PTR_ERR(data->regmap);
+	}
+
+	/*
+	 * AVDD is the analog voltage supply (2.6V to 3.3V)
+	 * VDDIO is the digital voltage supply (1.8V)
+	 */
+	data->regulators[0].supply = "avdd";
+	data->regulators[1].supply = "vddio";
+	error = devm_regulator_bulk_get(&client->dev, ARRAY_SIZE(data->regulators),
+				      data->regulators);
+	if (error) {
+		dev_err(&client->dev, "Failed to get regulators %d\n", error);
+		return error;
+	}
+
+	error = devm_add_action_or_reset(&client->dev, fts_power_off, data);
+	if (error) {
+		dev_err(&client->dev, "failed to install power off handler\n");
+		return error;
+	}
+
+	error = devm_request_threaded_irq(&client->dev, client->irq, NULL,
+					fts_ts_interrupt, IRQF_ONESHOT,
+					client->name, data);
+	if (error) {
+		dev_err(&client->dev, "Failed to request IRQ: %d\n", error);
+		return error;
+	}
+
+	error = fts_input_init(data);
+	if (error)
+		return error;
+
+	return 0;
+}
+
+static int fts_pm_suspend(struct device *dev)
+{
+	struct fts_ts_data *data = dev_get_drvdata(dev);
+
+	mutex_lock(&data->input_dev->mutex);
+
+	if (input_device_enabled(data->input_dev))
+		fts_stop(data);
+
+	mutex_unlock(&data->input_dev->mutex);
+
+	return 0;
+}
+
+static int fts_pm_resume(struct device *dev)
+{
+	struct fts_ts_data *data = dev_get_drvdata(dev);
+	int error = 0;
+
+	mutex_lock(&data->input_dev->mutex);
+
+	if (input_device_enabled(data->input_dev))
+		error = fts_start(data);
+
+	mutex_unlock(&data->input_dev->mutex);
+
+	return error;
+}
+
+static const struct dev_pm_ops fts_dev_pm_ops = {
+	.suspend = fts_pm_suspend,
+	.resume = fts_pm_resume,
+};
+
+static const struct of_device_id fts_match_table[] = {
+	{ .compatible = "focaltech,fts5452", },
+	{ .compatible = "focaltech,fts8719", },
+	{ /* sentinel */ },
+};
+
+MODULE_DEVICE_TABLE(of, fts_match_table);
+
+static struct i2c_driver fts_ts_driver = {
+	.probe_new = fts_ts_probe,
+	.driver = {
+		.name = FTS_DRIVER_NAME,
+		.pm = &fts_dev_pm_ops,
+		.of_match_table = fts_match_table,
+	},
+};
+module_i2c_driver(fts_ts_driver);
+
+MODULE_AUTHOR("Joel Selvaraj <joelselvaraj.oss@xxxxxxxxx>");
+MODULE_AUTHOR("Caleb Connolly <caleb@xxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("FocalTech touchscreen Driver");
+MODULE_LICENSE("GPL");
- Markuss



[Index of Archives]     [Linux Media Devel]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Linux Wireless Networking]     [Linux Omap]

  Powered by Linux